Teletek electronics TFT Istruzioni per il montaggio

Attention:

This manual contains information on limitations regarding product use and

function and information on the limitations as to liability of the manufacturer.

The entire manual should be carefully read.

The information in this manual is a subject to change without notice!

ver. 1.0.8

IRIS/SIMPO

Repeater

Addressable Fire Alarm Repeater Panel

Model: TFT

Installation &

Programming Manual

IRIS/SIMPO Repeater TFT - Addressable Fire Alarm Repeater Panel –Installation & Programming Manual 
 

 
Table of Contents 
 
INTRODUCTION........................................................................................................................................................ 4 
1. General Description ................................................................................................................................... 4 
2. General Specifications............................................................................................................................... 4 
3. Technical Specifications ............................................................................................................................ 4 
4. Functional Features ................................................................................................................................... 4 
INSTALLATION.......................................................................................................................................................... 5 
1. Wall Mounting ............................................................................................................................................ 5 
2. Initial Power-up .......................................................................................................................................... 7 
3. Sound Signalization ................................................................................................................................... 7 
ELECTRICAL CONNECTIONS ................................................................................................................................. 7 
1. PCB Elements............................................................................................................................................ 7 
2. Main Power Supply.................................................................................................................................... 8 
3. Redundant Network RS485 ....................................................................................................................... 8 
4. LAN Network.............................................................................................................................................. 9 
5. Hardware Restore Defaults........................................................................................................................ 9 
INSTALLER PROGRAMMING MENUS .................................................................................................................... 10 
1. Common Information.................................................................................................................................. 10 
1.1. Functional Buttons for Operation ............................................................................................................ 10 
1.2. General Information for Text Introducing................................................................................................ 10 
1.3. General Information for Digits Introducing.............................................................................................. 11 
1.4. Quick Logging Out of the Installer Programming Menus........................................................................ 11 
2. Programming Menus.................................................................................................................................. 12 
2.1. Panel Settings............................................................................................................................ 12 
2.1.1. Setting Access Codes and Levels for Operation....................................................... 12 
2.1.2. Setting of Network Parameters.................................................................................. 14 
2.1.2.1 Network Settings......................................................................................... 14 
2.1.2.2. Panels........................................................................................................ 15 
2.1.3. Disable the Internal Buzzer........................................................................................ 17 
2.1.4. Changing the Language............................................................................................. 17 
2.1.5. “Screen-Saver” – Company Logo Setting.................................................................. 17 
2.2. Restore Defaults ........................................................................................................................ 18 
2.3. Save the Configuration .............................................................................................................. 18 
3. Maintenance Menus................................................................................................................................... 18 
3.1. Setting Time............................................................................................................................... 19 
3.2. Setting Date ............................................................................................................................... 19 
3.3. Setting the Display..................................................................................................................... 19 
3.3.1. Coordinates Calibration ............................................................................................. 20 
3.3.2. Colors Review............................................................................................................ 21 
3.3.3. Setting the Screen Backlight...................................................................................... 21 
3.4. Software Revision and Firmware Update .................................................................................. 21 
3.5. Review the Log Memory for Events........................................................................................... 22 
3.6. Clear the Log Memory for Events .............................................................................................. 23 
APPENDIX А.................................................................................................................................................................. 23 
APPENDIX B.................................................................................................................................................................. 26 
 
 
 
 
 
 
 
 
 
 
 
 

IRIS/SIMPO Repeater TFT - Addressable Fire Alarm Repeater Panel –Installation & Programming Manual

GUARANTEE

The guarantee terms are determined by the serial number (barcode) of the electronic device!

During the guarantee period the manufacturer shall, at its sole discretion, replace or repair any defective product when it is returned to the factory. All

parts replaced and/or repaired shall be covered for the remainder of the original guarantee, or 6 months, whichever period is longer. The original

purchaser shall immediately send manufacturer a written notice of the defective parts or workmanship.

INTERNATIONAL GUARANTEE

Foreign customers shall possess the same guarantee rights as those any customer in Bulgaria, except that manufacturer shall not be liable for any

related customs duties, taxes or VAT, which may be payable.

GUARANTEE PROCEDURE

The guarantee will be granted when the appliance in question is returned. The guarantee period and the period for repair are determined in advance.

The manufacturer shall not accept any product, of which no prior notice has been received via the RAN form at: http://teletek-electronics.com/en/ran-

form

The setup and programming included in the technical documentation shall not be regarded as defects. Teletek Electronics bears no responsibility for

the loss of programming information in the device being serviced.

CONDITIONS FOR WAIVING THE GUARANTEE

This guarantee shall apply to defects in products resulting only from improper materials or workmanship, related to its normal use. It shall not cover:

•Devices with destroyed serial number (barcode);

•Damages resulting from improper transportation and handling;

•Damages caused by natural calamities, such as fire, floods, storms, earthquakes or lightning;

•Damages caused by incorrect voltage, accidental breakage or water; beyond the control of the manufacturer;

•Damages caused by unauthorized system incorporation, changes, modifications or surrounding objects;

•Damages caused by peripheral appliances unless such peripheral appliances have been supplied by the manufacturer;

•Defects caused by inappropriate surrounding of installed products;

•Damages caused by failure to use the product for its normal purpose;

•Damages caused by improper maintenance;

•Damages resulting from any other cause, bad maintenance or product misuse.

In the case of a reasonable number of unsuccessful attempts to repair the product, covered by this guarantee, the manufacturer’s liability shall be

limited to the replacement of the product as sole compensation for breach of the guarantee. Under no circumstances shall the manufacturer be liable

for any special, accidental or consequential damages, on the grounds of breach of guarantee, breach of agreement, negligence, or any other legal

notion.

WAIVER

This Guarantee shall contain the entire guarantee and shall be prevailing over any and all other guarantees, explicit or implicit (including any implicit

guarantees on behalf of the dealer, or adaptability to specific purposes), and over any other responsibilities or liabilities on behalf of the manufacturer.

The manufacturer does neither agree, nor empower, any person, acting on his own behalf, to modify, service or alter this Guarantee, nor to replace it

with another guarantee, or another liability with regard to this product.

UNWARRANTED SERVICES

The manufacturer shall repair or replace unwarranted products, which have been returned to its factory, at its sole discretion under the conditions

below. The manufacturer shall accept no products for which no prior notice has been received via the RAN form at: http://teletek-

electronics.com/en/ran-form.

The products, which the manufacturer deems repairable, will be repaired and returned. The manufacturer has prepared a price list and those

products, which can be repaired, shall be paid for by the Customer. The devices with unwarranted services carry 6 months guarantee for the replaced

parts.

The closest equivalent product, available at the time, shall replace the products, the manufacturer deems un-repairable. The current market price shall

be charged for every replaced product.

STANDARDS AND CONFORMITY

Conforms and approved in accordance with CPR (Construction Products Regulation).

DOCUMENTATION FEEDBACK

If you have any comments or suggestions on our products’ manuals or installation instructions you can email us on: info@teletek-electronics.bg

Your feedback on product documentation will help us to improve the contents of our manuals and stickers and keep them up-to-date.

Please, include in your feedback email the product name, the revision of the manual or instruction (8-digit number with Revision and date of issue)

and the page number.

1293

DoP No: 138

Teletek Electronics JSC

Bulgaria, Sofia 1407, 14А Srebarna Str., Tel.: +359 2 9694 800, Fax: +359 2 962 52 13

e-mail: info@teletek-electronics.bg

IRIS/SIMPO Repeater

Intended for use in fire detection and fire alarm systems in and around buildings.

IRIS/SIMPO Repeater TFT - Addressable Fire Alarm Repeater Panel –Installation & Programming Manual

1. INTRODUCTION

1.1. General Description

IRIS/SIMPO Repeater TFT is a control panel for remote indication of fire alarm, fault, trouble, warning and other type of

events, reported from iRIS8, SIMPO and other Repeater panels connected into one common network. The IRIS/SIMPO

Repeater can operate only as a part of a network. It repeats the status of the connected fire panels and informs for

events.

Up to 64 panels can operate in a single network, including IRIS/SIMPO Repeater, iRIS8 and SIMPO fire alarm panels.

The connection in the network between the panels can be realised via LAN or RS232 communication protocol. Only one

type of connection can be used in a single network.

1.2. General Specifications

The front panel of Repeater TFT has a color graphic LCD touch screen display (800/480 TFT) performing user-friendly

operation with menus. Separate user, maintenance and installer passwords provide access to the functions of the

panel. The panel has a built-in real time clock and calendar, supported with built-in battery in case of main and backup

power supply failure.

Events like FIRE, RESET, FAULTS, etc., including for the rest of the panels in the network, are saved in the memory,

thereby creating an event log-file. It contains the time and date, the fire panel number, the address of the device, the

type (module, detector, sounder or periphery device), the name of the device, the zone, the name of the zone, etc.

1.3. Technical Specifications

•Main Power Supply*...................................................24±4V DC

•Frequency ..................................................................50/60Hz

•Maximal Consumption................................................0.4A

•Cross Section of the Connection Wires .....................0.5-2.5mm2

•Maximum distance between two panels ....................up to 1000m

•Operating Temperature..............................................from -5°C to +50°C

•Relative Humidity Resistance ....................................up to 95% (without condense)

•Dimensions.................................................................200x330x48mm

•Weight........................................................................0.90kg

* Note: 24V DC External power supply with backup batteries. It is possible to power on the Repeater panel from an

addressable Fire alarm panel (AUX output of iRIS8 or SIMPO panel), but this is not recommended for big system

configurations.

Attention: The earth connection has to be realized in accordance with the rules for the electrical safety with the total

resistance in the circuit lower than 10Ω. It is mandatory to connect the earth connector of the main power supply cable

to the middle input of the Repeater panel terminal and check the connection to be tight and stable - see item 3.2.

1.4. Functional Features

•Operation in a common network with iRIS8, SIMPO and other Repeater panels.

•TTE Communication Protocol

•Up to 64 panels in a redundant network.

•Ring or Line network type topology

•RS485 interface

•LAN interface

•Micro USB port for software and firmware update

•Memory log for 10000 events

•TFT color screen touch display

•Multilanguage support of the menus

•Built-in battery supporting real-time clock and date in case of main and backup power supply failure

•Built-in buzzer for sound indication of events

IRIS/SIMPO Repeater TFT - Addressable Fire Alarm Repeater Panel –Installation & Programming Manual

2. INSTALLATION

Attention:

Do not install the Repeater panel near power electromagnetic fields (radio equipment, electric motors, etc.)!

The panel should be installed by qualified specialists only.

The electronic components of the panel are vulnerable to electrostatic discharge.

2.1. Wall Mounting

•The Repeater panel must be installed in a clean dry place and must not be subjected

to impacts or vibrations. It must be situated far from heating appliances. The

temperature must be within -5ºСand +50ºC.

The recommended mounting height is 1500 –1600 mm up from the floor surface.

The TFT screen must be well visible from the users and situated approximately at eye

level.

Leave enough space from all wall corners, at least 300 mm. The right side of the

Repeater must be free for access because of the micro USB for software and firmware

updates.

Attention: The Repeater panel is not water-proof!

• The main elements of the enclosure box are presented in Figure 2.

Figure 2

1–TFT color touch screen.

2–Front cover.

3–Left and Right side covers.

4–Clips on the box bottom holding the side covers.

• The left and right side covers, are mounted to the box bottom via clips. To remove the side covers, press the clip at the

box bottom (1) and pull the cover upward (2) –Figure 3.

Figure 3

Figure 1

IRIS/SIMPO Repeater TFT - Addressable Fire Alarm Repeater Panel –Installation & Programming Manual

• The left and right side covers, are specific and cannot be exchanged with one another. The covers have marks at the

back side, showing the position (left or right) for mounting.

To proceed with wall mounting, the installer must remove the front cover from the bottom –Figure 4.

1–Left side cover. It has a mark “1” at the back side.

2–Right side cover. It has a mark “2” at the back side.

3–Use a crossed slot screwdriver to undo the screws

holding the front cover to the box bottom.

Attention: Be careful not to damage the TFT touch

screen while dismounting the front cover!

Figure 4

• For running the cables for main power supply and network connection, make appropriate holes at the box bottom

being careful not to damage the PCB and TFT screen of the Repeater panel.

• Mount the box bottom at the installation place using appropriate fixtures according the mounting surface. Note that, not

all of the mounting holes at the box bottom are available for use. Lever horizontally the box, before tighten the screws.

Attention: Do not remove the PCB from the box bottom!

Figure 5

• Run the cables and make the network and electrical connections, BUT DO NOT power on the panel on this step.

• Place the front cover back and tighten the screws.

• Mount the Left and Right side covers to the box bottom as observe their correct place –look for the marks at the back

side –Figure 6. Press the side cover downwards until a click is heard.

Figure 6

IRIS/SIMPO Repeater TFT - Addressable Fire Alarm Repeater Panel –Installation & Programming Manual

2.2. Initial Power-up

When turned on, the Repeater panel always conducts a procedure of loading the parameters, which usually takes about

30 sec. A long sound signal is heard. There is no access to the menus of the Repeater panel during that procedure.

Access Level 1 is loaded. Upon the initial start-up, the Repeater does not hold any configurations.

Next, the installer has to perform settings for the network and the parameters of the Repeater as described at item 4.

2.3. Sound Signalization

The IRIS/SIMPO Repeater panel is equipped with internal buzzer for sound signalization in case of events.

Signalization

Description

Button

Single short beep indicating the pressing of a button.

Reset or Event

Single long beep indicating reset of the Repeater or receiving of message for Disable, Test or

Warning event.

Technical trouble

Short beeps in case of receiving of messages for Fault event (for the Repeater itself or for other fire

alarm panels in the network). The beeps can be stopped from Access Level 2 and 3 after

performing Silencing Buzzer from the Main Screen menu.

The beeps will stop when the technical trouble is restored and the fault event is cleared

automatically from the Faults list.

Fire Alarm

Continuous sound signal for activated Fire Alarm from zone or Evacuation. The sound can be

stopped from Access Level 2 and 3 after performing Silencing Buzzer from the Main Screen menu.

3. ELECTRICAL CONNECTIONS

3.1. PCB Elements

Attention: Do not remove the PCB from the box bottom!

Figure 7

1–Main power supply terminal. See item 3.2.

2–RS485 interface. Used for realizing network with other panels via RS485 communication

protocol. See item 3.3.

3 –LED Indication for the status of the network via RS485 interface. See item 3.3.

4 –LAN interface connector. See item 3.4.

5 –Micro USB port for software and firmware update. See also item 4.3.4.

6 –Jumper for hardware restore defaults. See item 3.5.

7 –Built-in 3V backup battery for the real-time clock and jumper BTR for battery activation. The

jumper BTR is factory set and must not be removed.

8 –Built-in sound buzzer (on the back side of the PCB).

TFT Touch Screen

IRIS/SIMPO Repeater TFT - Addressable Fire Alarm Repeater Panel –Installation & Programming Manual

3.2. Main Power Supply

Connect the external power supply unit 24V DC as observe the polarity of the connection. It is recommended to use

power supply unit with backup batteries to guarantee the operation of the Repeater in case of mains power supply

failure.

3.3. Redundant Network RS485

The Repeater panel is designed with option for connection in a redundant network with other SIMPO, iRIS8 and

Repeater panels (up to 64). The redundant network is based on RS485 interface.

The RS485 interface is built-in the Repeater panel. For operation in a common redundant network with other fire panels

they must be equipped with Redundant Network Module –Figure 8. The Redundant network module is connected to

“NETWORK” interface connector on the fire panel PCB (interface module in iRIS8).

Note: The RS485 interface terminals are accessible after removing the left side cover of the enclosure box.

Figure 8

The following table represents the correspondence of Tx/Rx terminal connections for IN and OUT communication lines.

Observe the polarity of

the RS485 interface

connection!

Repeater TFT

OUT

Redundant

Network

Module

OUT

In installer’s menu (Access Level 3) enter SYSTEM –PROGRAMMING –PANEL –NETWORK –NETWORK

SETTINGS, and set option “RS485” for Network type –see item 4.2.1.2.1.

Fire Panel

iRIS8/

SIMPO

Redundant

Network

Module

Repeater

TFT

Indication

LEDs

Indication

LEDs

External power

supply unit

The LED indication for RS485 interface in both

Repeater and Redundant module has same meaning:

•OUT - Output communication

•Central Commun. - Panel-Module

communication

•IN - Input communication

In normal operation mode the LEDs are blinking.

In case of trouble with the communication line the

LES are lighting on.

IRIS/SIMPO Repeater TFT - Addressable Fire Alarm Repeater Panel –Installation & Programming Manual

The maximum cable length between two network modules and/ or repeater panel is 1000m.

Figure 9

Up to 64 panels can be connected in a common redundant network.

Figure 10

3.4. LAN Network

The realization of LAN network is possible only for Repeaters and other iRIS8 addressable fire alarm panels (up to 64).

The LAN connection can be direct panel-to-panel or by means of a HUB via TCP/IP protocol.

Note: The LAN connector is accessible after removing the left and right side covers and the front panel of the enclosure

box –see item 2.1 and Figures 4 and 5.

In installer’s menu (Access Level 3) enter SYSTEM – PROGRAMMING –PANEL –NETWORK –NETWORK

SETTINGS, and set for Network type option “LAN” –see item 4.2.1.2.1.

3.5. Hardware Restore Defaults

This is an option for restoring the factory set parameters of the Repeater panel.

It is recommended, before making a Restore Defaults of the Repeater, to save its current system configuration

as TDF file using ProsTE specialized programming software. After hardware resetting, load the TDF back to the

Repeater and save time for introduce settings in menus. For details about ProsTE specialized programming software

ask your local distributer of the equipment.

To perform hardware, restore defaults do as follows:

1. Turn off the main and backup power supply of the Repeater panel.

2. Remove the right side cover as shown on Figure 3.

3. Put a jumper on Restore Defaults terminals on the PCB of the Repeater –Figure 7, position 6.

4. Turn on the main and backup power supply of the Repeater. A long sound signal is heard. The screen enters into

procedure for hardware calibration of the display. Perform the calibration as follow the detailed description how to do

that in item 4.3.3.1 .

5. Remove the Restore Defaults jumper.

6. Close the right side cover of the enclosure box.

Maximum 64 panels

iRIS8 Fire panel

SIMPO Fire panel

Repeater TFT

Redundant network

Module 1

Redundant network

Module 2

iRIS8 Fire panel

SIMPO

Fire panel

Repeater TFT

Power

supply

24V DC

Redundant

Module

Redundant

Module

Redundant

Module

IRIS/SIMPO Repeater TFT - Addressable Fire Alarm Repeater Panel –Installation & Programming Manual

4. INSTALLER PROGRAMMING MENUS

4.1. Common Information

At Access Level 3 the Installer has full rights for entire programming of the Repeater.

To enter the Installer Programming menus, press ACCESS button from the Main Screen and introduce the code for

Access Level 3 –3333 is the default factory set combination.

Press ACCESS button to change the Access Level.

Enter code for Access Level 3 entry (3333 –by default)

and confirm with OK button.

4.1.1. Functional Buttons for Operation

Button

Description

Confirmation and saving of the entered parameters.

Step back in programming menus. Cancelling the introduced changes.

Enter in additional submenu.

Quick button for exit the programming menus and returning back to Main Screen.

4.1.2. General Information for Text Introducing

The text introducing is via virtual keyboard, presenting access to different type of letters, symbols and numbers. The

virtual keyboard is shown on the screen after pressing an active text field. Up to 40 symbols, including space intervals,

can be entered for a name or other description in the system.

After pressing an active text field in a menu, the screen displays the virtual keyboard.

Latin Letters screen keyboard.

Use the special buttons to switch to different type of letters

or symbols. After entering the text and confirming with

ENTER button you must also save the text with APPLY

button on the respective programming menu.

Press EXIT to reject the entered text and go back to

programming menus.

- Switch to Cyrillic Letters

- Switch to Latin Letters

- Switch to Special Letters

- Switch to Symbols

- Switch to Digits

- Switch between Capital and Small Letters

- Enter (confirmation) button.

- Backspace (delete) button.

Altri manuali per TFT

Indice

Altri manuali Teletek electronics Ripetitore

Teletek electronics

Teletek electronics TFT Guida all'installazione

Manuali Ripetitore popolari di altre marche

Gigaset

Gigaset 108 Manuale utente

Ace TECHNOLOGY

Ace TECHNOLOGY USR-1900A Manuale utente

Kenwood

Kenwood TKR-750-850 Manuale elenco delle parti

Asus

Asus RP-AC51 Manuale utente

Exibel

Exibel HRP0101 Manuale utente

Kidde

Kidde Vega Manuale utente

Telcosat

Telcosat RBB 850 Guida all'installazione

York

York Universal LINC485 Manuale utente

MIKOM

MIKOM MRx01B Power Series Manuale utente

Simrad

Simrad RD 301 Manuale utente

Tait

Tait TB7304 Manuale utente

R-tron

R-tron RSN-CDMA-37-C Manuale utente

Inventronics

Inventronics DALI REPEATER SO Manuale utente

XFP

XFP 16 Manuale utente

Andrew

Andrew MRx18 Manuale utente

COMBA

COMBA RXA3748 Manuale utente

ADRF

ADRF SDR-ICS-43 Manuale utente

Teltonika

Teltonika WRP100 Manuale utente