TELETRAC NAVMAN Qtanium 400 Manuale utente

Qtanium 400

INSTALLATION MANUAL

Qtanium 400 | Installation Manual 
 ii 
Contents 
1OVERVIEW ................................................................................................................. 5 
2HARDWARE ............................................................................................................... 6 
1 OTHER COMPONENTS REQUIRED .......................................................................................6 
2 POWER CABLE OPTIONS ..................................................................................................6 
3 I/O CABLES FOR (OPTIONAL)ADDITIONAL CONNECTIONS.......................................................6 
3MOUNTING LOCATIONS............................................................................................. 7 
1 ANTENNA MOUNTAIN LOCATION.......................................................................................7 
2 QTANIUM 400 MOUNTING LOCATION ...............................................................................7 
4INSTALLATION............................................................................................................ 9 
1 BEFORE STARTING ..........................................................................................................9 
2 START THE INSTALLATION .................................................................................................9 
3 MOUNT THE QTANIUM 400...........................................................................................10 
4 CABLING.....................................................................................................................10 
5 CONNECT THE POWER CABLE ..........................................................................................11 
6 CONNECT THE POWER CABLE/BUILT-IN IPS UNIT ...............................................................12 
7 CONNECT THE EXTERNAL BATTERY BACKUP OR SOLAR PANEL (OPTIONAL) ...............................13 
8 CONNECT ANY OPTIONAL EQUIPMENT..............................................................................14 
8.1 Digital Inputs.......................................................................................................14 
8.2 Digital Outputs....................................................................................................16 
8.3 Multi I/O-1 & I/O-2..............................................................................................17 
8.4 Connect the 7-Way Cable (Optional) ..................................................................18 
8.5 Teletrac Navman Temperature Probes...............................................................18 
8.6 Connect an 18-Way Cable (Optional) .................................................................18 
8.7 Connection to a Quake Satellite Modem ............................................................19 
9 POWER UP THE QTANIUM 400.......................................................................................19 
10 TEST THE INSTALLATION WITH ONLINEAVL2/DIRECTOR ....................................................20 
11 APPLY THE TAMPER-EVIDENT SEAL...................................................................................21 
5TROUBLESHOOTING................................................................................................. 22 
1 RECOMMENDED PROCEDURE ..........................................................................................22 
2 PERFORM A COLD RESET ................................................................................................22 
6DIMENSIONS............................................................................................................ 24 
7SPECIFICATIONS....................................................................................................... 25 

Qtanium 400 | Installation Manual

iii

Qtanium 400 | Installation Manual

Disclaimer

It is the Owner’s sole responsibility to install and use the Qtanium 400 (the Product) in a manner that will

not cause accidents, personal injury or property damage. For the purpose of this notice, “Owner”, “you”

and “your” means the party (including any person authorized by that party to use and/or install the

Product) that has either: (a) purchased the Product; (b) leased or rented the Product from Teletrac

Navman or its related companies; or (c) subscribes to Teletrac Navman’s subscription service and such

subscription incorporates the use of the Qtanium 400 product.

The Owner of this Product is solely responsible for observing safe driving practices.

The choice, location and installation of all components of the Product is critical. If installation is not

correct, the Product may not perform at its designed potential or specifications. If in doubt, consult your

Teletrac Navman dealer.

The Qtanium 400 is sealed in the factory and tested for watertight integrity. Unauthorized opening of the

unit will compromise the IP-67 rating, will invalidate the warranty, and may result in failure due to ingress

of water or other substances.

TO THE MAXIMUM EXTENT PERMITTED BY LAW, ALL REPRESENTATIONS AND WARRANTIES (EXCEPT ANY

WHICH MAY NOT LAWFULLY BE EXCLUDED) ARE, EXPRESSLY EXCLUDED, INCLUDING WITHOUT PREJUDICE

TO THE, GENERALITY OF THE FOREGOING, THE IMPLIED WARRANTIES OR MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. TO THE MAXIMUM EXTENT PERMITTED BY LAW TELETRAC

NAVMAN DISCLAIMS ALL LIABILITY ARISING OUT OF OR IN CONNECTION WITH THE PRODUCT (INCLUDING

ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS, DAMAGE OR VIOLATE THE LAW).

As Teletrac Navman is continuously improving this Product, Teletrac Navman may make changes to the

Product at any time which may not be reflected in this document. Please contact your nearest Teletrac

Navman office if you require any further assistance.

TELETRAC NAVMAN DISCLAIMS ALL LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE

ACCIDENTS, DAMAGE OR VIOLATE THE LAW.

EMC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

respective owners.

Qtanium 400 | Installation Manual

1 Overview

The Qtanium 400 is a ruggedized Automatic Vehicle Location (AVL) unit that is installed into

heavy duty vehicles (assets) such as those used for construction. It communicates with a

server and allows information about the asset to be stored and monitored.

The Qtanium 400 is a combined GPS (Global Positioning System) and communications

product that contains:

a GPS receiver to provide accurate location data

a cellular antenna that enables data to be transferred between the asset and the

server

an on-board microprocessor for data processing and storage, and external

communications

6 Digital I/O and 2 Multi I/O

an internal battery that is charged from a permanent external power supply, such as

the asset’s battery, through the power cable. When fully charged, the internal

battery has the capacity to report one event per day for up to three months. It takes

approximately 25 hours to charge the internal battery following a full discharge,

although this time can vary depending on the external temperature

In addition, the Qtanium 400 can optionally be connected to:

an external lead-acid backup battery, to avoid full discharge of the internal battery

a solar panel for trickle charging the internal battery

a maximum of 6 Teletrac Navman temperature probes

an MDT, M-Nav, or other serial device

other auxiliary devices

Note This installation manual is written for professional vehicle technicians.

Qtanium 400 | Installation Manual

2 Hardware

The box contains:

1 Qtanium 400

4 mounting magnets

Qtanium 400 Quick Install Card

2.1 Other Components Required

You also need the following components before starting the installation:

a power cable (see the following section for options)

a cellular antenna

a GPS antenna

WIFI antenna (with WIFI option)

You may also need any or all of the following components, depending on your installation:

I/O cable(s) to connect digital or other types of auxiliary devices and sensors

2.2 Power Cable Options

There are two choices of power cable:

3 m (9.8 ft.) heavy duty 16-gauge wire, plastic armored sheath with choke

6 m (19.6 ft.) heavy duty 16-gauge wire, plastic armored sheath with choke

2.3 I/O Cables for (Optional) Additional Connections

There are three choices of ruggedized cable for optional additional connections:

7-Way cable (SAP Code 10001345) for digital sensors or devices I/O

18-Way cable (SAP Code 10001346) for auxiliary or serial devices I/O

18-Way satellite modem cable (SAP Code 10001384) for connection to a Quake

Satellite Modem and/or auxiliary or serial devices

Note If desired, you can mount the Qtanium 400 using high-powered magnets such as

M5 or equivalent (not supplied).

Note The power cable and two antennas are the minimal requirement for tracking

only.

Qtanium 400 | Installation Manual

3 Mounting Locations

3.1 Antenna Mountain Location

Ensure that the antenna location provides a good view of the sky for optimum GPS

performance. You must use a Teletrac Navman-approved antenna. This must be IP-67 rated

if the antenna will be mounted in an exposed location with little or no protection from the

weather.

3.2 Qtanium 400 Mounting Location

The installation is considered to be permanent because the firmware can be updated

without removing the Qtanium 400 from the asset.

When selecting a mounting location, consider the length of the cables and proximity to all

connection points. Mount the Qtanium 400 and associated cabling in a location that does

not contain moving parts or obstruct serviceable areas.

Although the Qtanium 400 has an IP-67 rating, Teletrac Navman recommends that you

mount it in a location that will provide maximum protection from dust, water, and vibration.

The Qtanium 400 is rated up to 70°C but Teletrac Navman recommends that you choose a

mounting location that minimises exposure to extreme temperatures. Also be aware that,

Important The antenna must be located at least 20 cm (8”) from any person to meet

FCC radio frequency exposure requirements.

Note Use of an antenna that is not approved by Teletrac Navman, or an antenna that

is installed contrary to recommendations, may result in poor GPS or cellular

performance and may invalidate your warranty.

Important The Qtanium 400 contains an accelerometer that detects movement. It is

critical that the Qtanium 400 is mounted securely on a rigid surface where it cannot

move independently of the asset and / or vibrate off its mounting location. The final

orientation of the Qtanium 400 after installation is not important.

Qtanium 400 | Installation Manual

due to the battery chemistry, battery operation will be impaired at high temperatures; in

particular, it will not charge when the temperature reaches, or exceeds, 45°C. need to check

ratings.

Qtanium 400 | Installation Manual

4 Installation

This section describes the process of installing the Qtanium 400 on a vehicle.

4.1 Before Starting

1. Check that you have all the components needed to complete your installation.

2. Identify the best mounting location for the Qtanium 400 and the antennas. Make

sure that the proposed location for the Qtanium 400 provides sufficient space for

easy access to its connectors.

3. Test the proposed antenna locations, if possible, to check whether they provide the

best performance.

4. Decide on the most suitable mounting method for your chosen location (screws /

nuts and bolts / magnets).

5. On the asset, identify where you will connect:

To asset’s chassis/after ground isolator switch (brown wire)

To asset’s battery negative/before ground isolator switch (black wire)

To asset’s +12/24V uninterrupted supply (red wire)

To asset’s ignition/run signal (pink wire).

6. Check that the power cable is long enough to reach between the power source and

your chosen location for the Qtanium 400.

7. Check that the antenna cables are long enough to reach between your chosen

locations for the Qtanium 400 and the antennas.

8. Check that any other cables are long enough to connect the Qtanium 400 to any

other optional devices or sensors.

4.2 Start the Installation

1. Disable the asset (turn the battery switch OFF or disconnect a battery post).

2. Mount the antenna and run the antenna cable but do NOT cut it. Where possible,

choose a location where the antenna has a clear view of the sky and is protected

from physical damage. (GPS performance will be impaired if the antenna cannot get

a clear view of the sky).

3. Run the Qtanium 400 power cable.

Qtanium 400 | Installation Manual

4.3 Mount the Qtanium 400

After you have run the Qtanium 400 power cable, mount the Qtanium 400 securely on - or

in - the asset using 4 self-tapping screws or 4 nuts and bolts.

Place the screws or bolts through the two slots along both sides of the Qtanium 400.

If you are mounting the Qtanium with magnets, we recommend magnetic mounts sized for

M5 screws.

The Qtanium 400 must be attached securely at all four corners.

4.4 Cabling

We recommend that you leave a service loop in each cable, near to the Qtanium 400, with

enough slack to allow working room and strain relief.

Ensure that all cabling is:

tidy and secure so that it is not a hazard to the users of the asset

protected from heat sources and from chaffing on sharp edges

connected to manufacturer’s approved points and run along factory harnesses

located where it will not be pinched or damaged.

Important Ensure that any holes drilled for the installation will not weaken the

structure of the asset or compromise the safety of the asset or its occupants. If in

doubt, consult the manufacturer. If mounting holes are required, use grommets to

ensure that the asset remains waterproof.

Important Individually insulate any unused bare wires and cover all unused ports

with end-caps. Use ONLY weatherproof sealable heatshrink ring terminals and butt

connectors for all electrical connections. Failure to use these may void the warranty

and damage the Qtanium 400 and / or other equipment. Do NOT use nylon or vinyl

connectors.

Indice

Altri manuali TELETRAC NAVMAN GPS

TELETRAC NAVMAN

TELETRAC NAVMAN Qube300 Guida all'installazione

TELETRAC NAVMAN

TELETRAC NAVMAN iFace Manuale utente

TELETRAC NAVMAN

TELETRAC NAVMAN TM470 Series Guida all'installazione

TELETRAC NAVMAN

TELETRAC NAVMAN iFace Manuale utente

TELETRAC NAVMAN

TELETRAC NAVMAN Qtanium 100 Manuale utente

TELETRAC NAVMAN

TELETRAC NAVMAN Qtanium200 Manuale utente

TELETRAC NAVMAN

TELETRAC NAVMAN Qtanium 100 Manuale utente

Manuali GPS popolari di altre marche

Raven

Raven Cruizer II Manuale

Hama

Hama 53118 Manuale utente

Garmin

Garmin SOUNDER 125 Manuale utente

Garmin

Garmin DEZL 580 Manuale utente

Jigabot

Jigabot EX Manuale utente

Pointer

Pointer Cellocator CelloTrack XT LTE Guida all'installazione

Queclink

Queclink GV55LITE Manuale utente

Voxson

Voxson Voxtrack GPS500 Manuale di istruzioni

Garmin

Garmin ECHOMAP PLUS Manuale utente

Starcom Systems

Starcom Systems Kylos Compact Manuale utente

Garmin

Garmin 15 H Series Manuale utente

Cobra

Cobra Marine MC 600Ci Manuale utente

Cellocator

Cellocator CelloTrack T Manuale utente

Enfora

Enfora Mini-MT GSM2228UG001 Manuale utente

Magellan

Magellan eXplorist 100 Manuale utente

LTE

LTE G50B Manuale utente

Garmin

Garmin DEZL OTR500 Manuale utente

SkyGolf

SkyGolf SkyCaddie SG1 Manuale utente