Telkom SS-10 3G Manuale utente

DOC. NO: SS-10 3G-14 (Rev. 01) Page 1 of 20

SS-10 3G

FIXED CELLULAR TERMINAL

USER MANUAL

DOC. NO: SS-10 3G-14 (Rev. 01) Page 2 of 20

Revision History:

Revision 01 Original document 12 August 2010

CONTENTS

1 INTRODUCTION.................................................................................................3

2 FEATURES.........................................................................................................4

2.1 PHYSICAL FEATURES .............................................................................................. 4

2.2 SOFTWARE FEATURES.............................................................................................4

2.3 MAINTENANCE FEATURES .....................................................................................4

3 DESCRIPTION....................................................................................................6

3.1 FRONT VIEW .............................................................................................................. 6

3.2 REAR VIEW ................................................................................................................6

4 SETUP ................................................................................................................7

5 SETTABLE PARAMETERS ...............................................................................8

5.1 BASIC SETUP..............................................................................................................8

5.2 REPORTING SETUP ...................................................................................................9

5.3 SIM & NETWORK..................................................................................................... 10

5.4 AUTHORIZED USER ................................................................................................ 11

5.5 HARDWARE SETTINGS .......................................................................................... 11

5.6 POWER DOWN TIME ............................................................................................... 11

5.7 CALL BARRING ....................................................................................................... 12

5.8 MISCELLANEOUS.................................................................................................... 12

5.9 CALL BACK .............................................................................................................. 12

5.10 SETUP INFORMATION ............................................................................................ 13

6 SERIAL PORT COMMANDS............................................................................13

6.1 SIMPLIFIED SERIAL PORT COMMANDS.............................................................. 13

7 SETUP OF THE UNIT BY USING THE SS-10 TOOL.......................................14

7.1 MAIN WINDOW........................................................................................................ 14

7.2 CALL PARAMETERS ............................................................................................... 15

7.3 CALL BACK .............................................................................................................. 16

7.4 CALL BARRING ....................................................................................................... 17

7.5 SMS OPTIONS........................................................................................................... 18

7.6 NETWORK ................................................................................................................ 19

8 UPGRADE OF THE SS-10 3G FIRMWARE.....................................................20

9 TECHNICAL SPECIFICATIONS.......................................................................20

10 CONTACT DETAILS ..............................................Error! Bookmark not defined.

DOC. NO: SS-10 3G-14 (Rev. 01) Page 3 of 20

1 INTRODUCTION

The purpose of the SS-10 3G Fixed Cellular Terminal (FCT) is to provide a means of

making telephone calls where there is no fixed line infrastructure or where it may be

more cost effective to use the GSM/3G infrastructure for carrying the call.

ARCHITECTURE

DOC. NO: SS-10 3G-14 (Rev. 01) Page 4 of 20

2 FEATURES

2.1 PHYSICAL FEATURES

Matches to complex line impedance

Power saving feed-bridge

Signal level indicator LEDs

Busy indicator

Network indicator

SMA antenna connector

Module On/Off switch allows Network Detach

Power supply 300mA at 12 VDC

RJ11 connector for telephone

DB9 connector for programming

900/1800 MHz operation in 2G GSM mode

900/2100 MHz operation in 3G UMTS mode (additional 850MHz optional)

2.2 SOFTWARE FEATURES

Comfort Tone

CLI restriction

Settable digit count

Settable dial timeout

Automatic call termination

Transmit & receive levels adjustable

Optional reversal

Optional line current break

Optional periodic module reboot

Full rate, enhanced full rate & half rate operation

Supports Adaptive Multi-rate (AMR)

Preferred network selection (Network locking)

2G, 3G or automatic network selection

Dial-In modem functionality (2G mode only)

4 minute timer to reset module if not registered on the network

128 Programmable Call Back numbers

Settable SIM Pin Number

Supports International SIM card operation

2.3 MAINTENANCE FEATURES

Routine periodic SMS reports

oFeed bridge voltages

oNumber of forcedly cut calls

oNumber of unanswered calls

oNumber of answered calls

oTotal duration of answered calls

SMS report on zero traffic (no calls made for specified interval)

Request reports

Request setting information

Change set-up information by SMS

2 authorized maintainers

DOC. NO: SS-10 3G-14 (Rev. 01) Page 5 of 20

Programmable by serial port, telephone or SMS

DOC. NO: SS-10 3G-14 (Rev. 01) Page 6 of 20

3 DESCRIPTION

3.1 FRONT VIEW

ON/OFF button

Holding in the On/Off button while the

unit is powered up enables setup mode

Power Indica

tor

Busy Indicator

Network Indicator

SIM card

tray

Press for

opening

SIM tray

Signal strength

indicator

SMA antenna

connector

3.2 REAR VIEW

Line Connector

RJ-11 Connector

(Only pins 2 & 3

are used)

PC Connector

DB9 Female - Used for

setup purposes

Use a standard PC

serial cable for

connecting the unit to

a PC

DC Connector

Connects a DC voltage

between 12V and 18V to

the unit

Description

Inside

DC positive volta

Outside

GROUND

DOC. NO: SS-10 3G-14 (Rev. 01) Page 7 of 20

4 SETUP

Setup of the SS-10 3G can be done by using one of the following

methods:

SMS Setup Method: Sending SMS commands to the unit;

Telephone Setup Method: Using a telephone connected to the SS-10 3G;

PC Serial Port Setup Method: Sending commands to the unit by connecting it

to a PC and use a Comms package like HyperTerminal, or

PC Serial Port Setup Method: Connect the unit to a PC using the SS-10 Tool

package;

Sending SMS

commands

Using a

Telephone

Using

Toolkit

Load the SS-10 Tool and refer to the notes

“Setup of the unit by using the SS-10

3G Tool’

The format of the commands

using SMS is as follows:

**<n>*<val>

where <n> is a command number and

<val> is a value.

Setup Mode must be enabled.

Holding in the On/Off button

while the unit is powered up

enables setup mode on the SS-

10 3G.

Dial the following:

<nn>*<ddd>#

Where nn is the parameter

number and ddd is the

required setting.

Sending

Commands using

a Comms package

From the serial port the format is:

**<nn>*<ddd><enter>

**<nn>,<ddd><enter>

Where nn is the parameter number and

ddd is the required setting

DOC. NO: SS-10 3G-14 (Rev. 01) Page 8 of 20

5 SETTABLE PARAMETERS

5.1 BASIC SETUP

Parameter

Description Notes

Total Digit Count

Sets the total number of digits required before dialing.

It is recommended that this parameter is set to 10.

Dial Timeout

Set dial timeout in 10ths of a second. Normally 4 seconds

This is the time taken before the call proceeds when numbers shorter

than the total digit count are dialed.

03 Call Progress Tones

Enable (1), disable (0)

Polarity Reversal Signalling

Set reversal time in 10ths of a second. To enable reversal on answer

add 100 to the number input. E.g. 04*20 sets the time to 2.0 seconds

without reversal on answer and setting 04*120 sets it to 2.0 seconds

WITH reversal on answer.

Break Pulse Signaling

Set the break time in 10ths of a second. Some PABX systems require a

current break to indicate that the call has terminated. The SS-10 3G

can provide such a break. If it is not required then set this parameter

to 0.

06 Call Line Identification

Restrict CLI (1) or allow CLI (0).

Transmit

evels

Set transmit lev

els 0

255 (64 normal)

Relative Level Value Description

-12 dB 32 Softer

-6 dB 64 Factory Setting

0 dB 128 Louder

+6 dB 255 Loudest

Receive Levels

Set receive levels 0

255 (64 normal)

Relative Level Value Description

-12 dB 32 Softer

-6 dB 64 Factory Setting

0 dB 128 Louder

+6 dB 255 Loudest

DOC. NO: SS-10 3G-14 (Rev. 01) Page 9 of 20

5.2 REPORTING SETUP

Parameter

Description Notes

No Call SMS Report

Set the interval, in minutes, after which a report may be sent by SMS if

no calls have taken place.

Set to 0 to disable ‘no call reporting’.

Routine Reports

Set the interval, in minutes, between routine reports that will be sent

by SMS to the pre-programmed destination.

Set to 0 to disable routine reporting.

SMS

eport

estination

Sets the destination number for SMS report. Please include country

code. Eg. +27828221381

SS-10 3G Identity

This command is only available from the serial port. It is used to set a

16 character ID so that the SS-10 3G can identify itself in SMS

messages that are sent.

DOC. NO: SS-10 3G-14 (Rev. 01) Page 10 of 20

5.3 SIM & NETWORK

Parameter

Description Notes

Sets the PIN

Sets the PIN (SimPin1). It is only needed if the SIM card has its PIN

set.

Using a PIN locked SIM

The SIM can be loaded into the SS-10 3G using the command:

**30*nnnn<enter>

where nnnn is the PIN number. It is important to make sure that the

PIN is entered correctly. If the PIN is not correct then the SS-10 3G

will output a message on the serial port indicating this. It will also flash

the IN USE and NETWORK LED’s in an alternating pattern until it is

powered down. Note that after 3 attempts the SIM will be blocked and

the PUK will have to be used to unblock the SIM. This will need to be

done using a normal GSM handset or the SS-10 Tool.

Using a BLANK SIM

If the SIM card is setup without a PIN, no further action needs to be

taken, as the SS-10 3G will recognize that no PIN is required and it

will automatically log onto the network.

Set Network Operator

5 digit network code - use space for automatic network selection.

Vodacom

MTN

Cell C

65501

6551

65507

Select Network Band (GSM/3G)

The unit can be made to only log onto the 2G GSM network (0) or only

the 3G UMTS network (2). Alternatively the unit can be set to

automatically select the network type with the best signal (1).

Enable

International Callback

This feature is for use with the eMobile International Callback SIM. (1)

enables the feature, (0) disables the feature. NB. Please remember to

set the Dialled Digit Count (see above) to a higher value (16

recommended) to support the length of international numbers. Line

current will be disconnected for +-10 sec if a call is terminated during

setup. This allows time for proper call clearing on the network.

Indice

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente