Tellabs 8860 Guida utente

Revision A

System Installation

76.8860IM31-A

Tellabs®8860 Multi-service Switch Router

FCC Notification

Statement Federal Communications Commission (FCC) Rules require that you be notified

of the following:

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the

interference at his own expense.

Changes or modifications not expressly approved by Tellabs Operations, Inc., in

writing can void the user’s authority to operate the equipment.

Industry Canada

Notification Statement Industry Canada interference-causing equipment regulations require that you be

notified of the following:

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du

Canada.

and international copyright laws, conventions, and treaties. Your right to use this

manual is subject to limitations and restrictions imposed by applicable licenses

and copyright laws. Unauthorized reproduction, modification, distribution, display

or other use of this manual may result in criminal and civil penalties.

Trademark Notice The following trademarks and service marks are owned by Tellabs Operations,

Inc., or its affiliates in the United States and/or other countries: AUDIO PLUS®,

CABLESPAN®, CEC-128™, DYNAMIC SIGNAL TRANSFER™, DXX®,

DXX logo®, EC DUO®, ENHANCED AUDIO PLUS®, EXPRESS/PATH®,

FOCUS™, MARTIS®, MARTISDXX®, MARTIS logo®, MARTISDXX logo®,

METROVANTAGE™,METROWATCH™, NETREACH®, NETWISE®,

SCULPTURED SOUND™, TELLABS®, TELLABS and T symbol®, T symbol,

TELLABS PROPARTNER™, TEL/MAP™, TEL/MOR®, THE WORLD

COMMUNICATES THROUGH TELLABS™, TITAN®, VERITY™, YOUR

NETWORKING PARTNER®.

Any other company or product names may be trademarks of their respective

companies.

Contact Information In an effort to improve the quality of this document, please notify Tellabs

Technical Assistance at 1.800.443.5555 in North America or 1.630.378.1192

outside North America if any anomalous conditions are observed.

Tellabs 8860 Multi-service Switch Router System Installation iii

Table of Contents

CHAPTER 1 Installation Overview

Overall Installation Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1. Unpack and Inspect the 8860 MSR and Components . . . . . . . . . . . . 1-2

2. Prepare Power Source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

3. Position, Load, and Cable the 8860 MSR . . . . . . . . . . . . . . . . . . . . . . . 1-2

4. Initialize the 8860 MSR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Installation Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

CHAPTER 2 Unpacking and Site Preparation

Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Unpacking the 8860 MSR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Uncrate and Inspect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

8860 MSR Crate Inspection and Disassembly . . . . . . . . . . . . . . . . . 2-3

Accessory Box Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Circuit Pack Crate Inspection and Disassembly . . . . . . . . . . . . . . . 2-5

Verify Receipt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Contacting Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

PN 76.8860IM31-A Tellabs 8860 Multi-service Switch Router System Installation

Returning Products to Tellabs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Tools and Supplies Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Rack Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Power Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

Optical Network PLM Description and Cable Connection. . . . . . . . . . . . . 2-11

Fast Ethernet PLM Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

DS3 Clear Channel and Channelized PLM Details. . . . . . . . . . . . . . . . . . . . 2-14

CHAPTER 3 Equipment Overview

8860 MSR Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Card Cage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

System Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Environmental Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Alarm LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Craft Display Panel and Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

ACO Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Card Status LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

Fan Tray Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

Cable Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

8860 MSR Rear Connector Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

Intershelf Cabling Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13

Serial Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13

Ethernet Management Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13

External Alarm Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13

T1 BITS External Timing Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

DC Power Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

Switch and Control Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

Using the Shutdown Button on the SCC . . . . . . . . . . . . . . . . . . . . . . . . 3-17

Universal Line Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18

Physical Line Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

Blank Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

CHAPTER 4 Installation

Rack-Mount the 8860 MSR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Adjusting Mounting Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Positioning and Securing 8860 MSR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

PN 76.8860IM31-A Tellabs 8860 Multi-service Switch Router System InstallationTel-

Connect Power and Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Ground the 8860 MSR Chassis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

Tri-Power Grounding and Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

Load the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

SCC and ULC Installation Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

Install the Switch and Control Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

SCC Slot Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

Loading SCCs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

Install the Universal Line Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13

ULC Slot Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13

Loading ULCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13

Install an OC-192c/STM-64c PLM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16

Install a 10 Gigabit Ethernet PLM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17

Install PLMs into the ULCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17

Inserting a PLM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17

Install Blank Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18

Install Card Slot Blank Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18

Install PLM Blank Panels into ULCs. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20

Connect PLMs to the Optical Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21

Connect T1 BITS Clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22

Connect 8860 MSR Alarm Outputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23

Connect a Local Console to the 8860 MSR. . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24

Apply and Verify Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25

Let the System Boot Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26

Log Into the 8860 MSR Console Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27

If you need to log out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27

Change the Default Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28

Set a Static Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29

Connect the Ethernet Management Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29

Connect to the IP Management Network. . . . . . . . . . . . . . . . . . . . . . . . 4-30

APPENDIX A 8860 MSR Specifications

8860 MSR Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

8860 MSR System Management and Alarm Specifications. . . . . . . . . . . . . . A-3

8860 MSR System Power Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4

Optical PLMs and Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5

OC-3 PLMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6

OC-12 PLMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-7

OC-48 PLMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-8

OC-192 PLMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-9

PN 76.8860IM31-A Tellabs 8860 Multi-service Switch Router System Installation

Other PLMs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-10

10 GigE PLM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-11

GigE PLM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-12

Fast Ethernet PLM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-13

DS3/E3 Clear Channel PLM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-14

DS3 Channelized PLM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-15

Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-16

Safety and Compliance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-17

Connector and Adapter Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-18

Console Serial Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-19

RJ45-to-DB9 Connector Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-20

Ethernet (IP Management) Connector . . . . . . . . . . . . . . . . . . . . . . . . . . A-21

External Alarm Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-22

External BITS Timing Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-23

Port Densities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-24

APPENDIX B Setting Boot Parameters

Viewing and Modifying Boot Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2

Tellabs 8860 Multi-service Switch Router System Installation vii

PREFACE About This Manual

The Tellabs 8860 Multi-service Switch Router System Installation

provides instructions for safely unpacking, installing, powering-

up, testing and servicing the Tellabs 8860 Multi-service Switch

Router (MSR). After completing the procedures in this

installation guide, you can start managing and configuring the

8860 MSR equipment with the Tellabs® Multi-service Operating

System.

This preface contains information about this manual, in the

following sections:

❑

Audience

❑

Organization

❑

Symbols

❑

General Safety Precautions

PN 76.8860IM31-A Tellabs 8860 Multi-service Switch Router System Installation

viii

Audience

The Tellabs 8860 Multi-service Switch Router System Installation manual is intended for

use by equipment administrators and NOC operators who are responsible for ensuring

integrity of received product, and performing equipment setup and initialization.

Organization

The Tellabs 8860 Multi-service Switch Router System Installation manual is organized as

follows:

❑

Chapter 1—Installation Overview

—Provides a quick glance of the task sequence typically

required for installing a 8860 MSR after all components have been removed from the

shipping crate, site preparation is completed, and all components have been inspected.

❑

Chapter 2—Unpacking and Site Preparation

—provides procedures and relevant information

for unpacking and mounting the 8860 MSR, and for connecting it to external facilities.

❑

Chapter 3—Equipment Overview

—describes the 8860 MSR chassis and all replaceable

components. This chapter also introduces the software tools used to control and

monitor the 8860 MSR.

❑

Chapter 4—Installation

—provides the procedures and relevant information for installing,

cabling, and connecting the 8860 MSR line cards and physical line modules.

❑

Appendix A— 8860 MSR Specifications

—lists physical, environmental, electrical, and

mechanical characteristics of the 8860 MSR switch components and physical line

modules (PLMs).

❑

Appendix B— Setting Boot Parameters

—provides guidelines for modifying boot parameters,

if absolutely necessary.

PN 76.8860IM31-A Tellabs 8860 Multi-service Switch Router System Installation

Symbols

This section presents the conventions used in this documentation to identify important

notes and various warnings.

NOTE

The pencil icon highlights important, noteworthy information. Be sure to

read information alongside this symbol to obtain guidelines for performing

tasks more efficiently.

ARNING

The warning symbol alerts you about action(s) or inaction(s) that could

lead to personal injury or damage to the 8860 MSR equipment.

The laser radiation symbol alerts you about actions that, if performed

incorrectly, can result in exposure to hazardous invisible radiation.

ESD W

ARNING

The electro-static discharge (ESD) warning symbol reminds you to observe

precautions to prevent electrostatic damage to static-sensitive assemblies

and circuits.

CAUTION

The caution symbol alerts you about any hazard that may result in physical

injury.

PN 76.8860IM31-A Tellabs 8860 Multi-service Switch Router System Installation

General Safety Precautions

This section presents the safety precautions that you must observe while working with

Viva equipment, in the following topics:

❑

Observe Warnings in Product Documentation

❑

Ground the 8860 MSR

❑

Do Not Substitute Parts or Modify Equipment

The safety precautions listed in this section represent warnings associated with certain

dangers of which Tellabs is aware. You, as the user of this product, must observe these

warnings and all other safety precautions necessary to ensure your personal safety as well

as the continued safe operation of the 8820 MSR in your operating environment.

Observe Warnings in Product Documentation

Warning symbols and advisory text are positioned at potentially hazardous procedures in

this manual. When you see these warnings, follow the instructions as well as any other

safety precautions that you deem necessary for installing, operating, and servicing Viva

equipment in your operating environment.

ARNING

Danger! Shock Hazard

Use extreme caution when working around power sources during

installation, operation, testing, and equipment adjustments.

Remove the power at its point of distribution before you connect or

disconnect power leads to the equipment.

Class 1 Laser Product

Class 2 LED Product

Using controls or adjustments, or performing procedures, other than as

specified herein, may result in exposure to hazardous invisible radiation.

CAUTION

Use of controls or adjustments of performance or procedures other than

those specified herein may result in hazardous radiation exposure.

Indice

Altri manuali Tellabs Router di rete

Tellabs

Tellabs 8600 Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza