Temper KOBTP400BL Manuale utente

TOA0006116V00

MANUAL DE INSTALACIÓN E

INSTRUCCIONES DE USO_P.10

INSTALLATION MANUAL AND

INSTRUCTIONS FOR USE_P.2

MANUAL DE INSTALAÇÃO E

INSTRUÇÕES DE USO_P.18

A. Introduction

By following the indications in this instruction manual, we guarantee correct operation, so that you can

enjoy the product you have purchased for many years. Read it carefully before using the towel warmer

and keep it in a safe place, it will be useful for any questions.

VERY IMPORTANT

• Read the installation and use manual before assembling and operating the equipment.

• Observe the warnings carefully.

• Install the equipment in a place where air can circulate.

• It is advisable to be mounted by qualied personnel

• WARNING RISK OF ELECTRIC SHOCK!

Turn o󰀨 the power before proceeding with the installation.

• Turn o󰀨 the power before continuing with the installation.

• Pay attention to this instruction sheet and read carefully before

using the device.

• This device has been designed for the exclusive use of a towel rail.

• The thermostat is designed to heat the liquid contained within the

towel dryer in combination with a heating element. Any other use

is prohibited.

• Do not use the towel rail for drying garments of synthetic or acrylic

composition. This device is only for drying textiles washed in water.

You must check before placing towels or other type of garment,

that this is capable of withstanding high temperatures.

• In the towel rack can reach up to 95 ° C temperature.

• When using the towel rack for towel drying, try not to place more

than 2 in the case of towel rails whose powers are between 350-

500W or more than 4 in the case of towel rails whose powers are

between 600-800W and that these are not superimposed, that is,

one on top of the other.

• Avoid placing the towels on the wall supports.

• Before using, make sure that the line voltage is the same as the

one specied for the device (see technical specications).

• Only use heating elements compatible with the type of dry towels used.

• In case of damage to the power supply cable, turn o󰀨el dispositivo

• And don’t manipulate it. Damaged power cables can be replaced

exclusively by the manufacturer or by an authorized service center.

• Store and transport the heating element exclusively in the

protective packaging.

• The replacement of the heating element can be done exclusively

by the product manufacturer.

• Children under 8 years old and people with reduced physical,

sensory or mental abilities can use the device only under

supervision. Children should not play with the device.

• Disconnect the power supply before cleaning or maintaining the

product.

• Cleaning and maintenance intended to be carried out by the user

should not be performed by children without supervision.

• For cleaning and maintenance of the towel rail, you should never

use chemical cleaning products, it will be su󰀩cient to use a dry

cloth or, in case of stains, a cloth dampened with water.

• You should not use the product before it is installed completely

and correctly.

• In order to avoid danger to very young children, this appliance

should be installed so that the lowest heated rail is at least 600mm

above the ground.

• Any repair work must be performed by an authorized service

center.

• Failure to comply with the above rules could compromise the

security of the system and void the warranty.

B. Recycling

This product cannot be treated as normal household waste. It has to be picked up

and arranged in places provided for him.

The purpose of recycling is to preserve the environment and reduce the

consumption of natural resources.

This symbol indicates the obligation to bring the product to an appropriate waste

collection site, in order to be in accordance with the directives 2012/19 / EU.

C. Installation guide

• Make sure the towel rail is not leaking.

• The towel rack should always be placed with the control on the bottom.

• The towel rail will not be placed directly on top of an electrical outlet.

• Avoid water jets hitting the equipment.

• Make sure that the mains voltage is the same as indicated in the technical specication.

• When installing in a room with a bath or shower, respect the “protection zones” indicated in the

RBT (in the United Kingdom according to the IEE cable directives). In addition, you must respect

all local security directives.

• The device must be protected by a 30mA di󰀨erential circuit breaker

• For models that do not have a plug, it is necessary to install a suitable omnipolar switch to ensure

complete disconnection if necessary.

• WARNING! Do not rotate the device more than 30º in both directions.

• Connect the energy cable.

D. Wall xing

See diagram on the last page of this manual.

• Remove the protective caps from the ends.

• Place the heated towel rail against the wall in the desired position.

• Using a pencil, mark their position on the wall around the support tubes. Make sure there is no

wiring in the wall where you will be drilling.

• With the help of a suitable drill and bit, drill the holes in the tile / wall to the required depth.

• Important: the holes must be drilled correctly aligned and suitable for the diameter of the plug

and the length of the wall anchor screws.

• Insert the xing plugs into the holes using a screwdriver. Repeat the procedure for each heated

towel rail attachment bracket.

• Mount the heated towel rail once you have xed the plugs in the desired place, then tighten the

brackets with the anchor screws.

E. Warranty

In the event of any incident during the warranty period, contact our Technical Assistance Service

(contact indicated on the back cover of this manual).

The company o󰀨ers a technical guarantee for the period of 3 years. The manufacturer guarantees

that this product does not present any material, design or manufacturing defect at the time of pur-

chase.

If during the warranty period the equipment does not function properly under normal use,

the manufacturer will repair or replace the product, as it deems appropriate under the con-

ditions stipulated below:

• For this guarantee to be valid, it will be necessary to present the original invoice or purchase

receipt.

• The guarantee will only apply if the serial number and model of the product are presented (reec-

ted on the sticker of the technical characteristics).

The manufacturer reserves the right to refuse warranty service when this information has been

removed or tampered with after the original purchase of the product.

• It is advisable to keep the original packaging and protections to avoid damage during transport, if

it is necessary to send the product to the Technical Assistance Service.

The warranty in no case covers product damage caused by the following causes:

• Incorrect use of the product for unsuitable purposes or without respecting the manufacturer’s ins-

tructions regarding the use and maintenance of the equipment, as well as incorrect installation or

use of the product in a way that does not comply with current technical safety standards.

• All problems arising from installation or insu󰀩cient power (insu󰀩cient power to heat the room,

improper installation, improper power supply, etc.) or damage during transportation are not covered

by this warranty.

• Repairs carried out by unauthorized service workshops or the opening of the equipment by unau-

thorized persons.

• Unforeseen accidents that are beyond the manufacturer’s control such as lightning, res, oods,

public disorders, etc.

• The repairs or replacements contemplated by this guarantee do not allow the extension or new

beginning of the guarantee period.

• The manufacturer reserves the right to decide whether to repair any defective part or replace all

equipment. Removed defective parts or components will become the property of the manufacturer.

• This warranty does not a󰀨ect the buyer’s legal rights under current national legislation, nor the

buyer’s rights against those of the distributor or installer arising from the contract of sale.

• In the absence of applicable national legislation in force, this warranty will be the sole protection

of the buyer. The manufacturer, its o󰀩ces and distributors and installers will not be liable for any

type of damage, both incidental and accidental, arising from violating any implicit rule related to this

product.

• In the last case of resorting to legislation, both parties will be under the jurisdiction of the courts of

the manufacturer’s province.

F. Technical specications

Features Comfort, Night, Antifreeze (7 ° C), Stand-by, Chrono, 2h timer, ECO, Open windows, ASC.

Certicates CE

Voltage and frequency 230 VAC - 50 Hz

Temperature control range 7°C ÷ 30°C

IP protection IP44

G. Operating modes

Operating modes: Comfort, Night, Anti-ice, Chrono, 2h Timer, Standby.

• In “Comfort” mode: the electronic control maintains the temperature set at the value set by

the user.

• In ‘’ Night ‘’ mode: the electronic control maintains the room temperature at a lower value than

the ‘’ Comfort ‘’ temperature.

• In “Anti-freeze” mode: the electronic control keeps the temperature above 7°C.

• In “2h timer” mode: the electronic control activates the heating element for 2 hours, uncondi-

tionally by the set temperature. At the end of this period, the thermostat operates again in the

previously set mode. During the 2 hours, for safety reasons, the ambient temperature cannot

exceed 30°C.

• In “Chrono” mode: the electronic control works according to a daily program with weekly repe-

tition, the program can be congured by the user.

• In ‘Wait’ mode: the resistance is deactivated but the electronic control is operational.

OTHER FEATURES

• Large backlit display showing: time, set temperature and function / mode.

• 3 preset daily programs and 1 user-congurable program.

• ‘’ Open Windows ‘’ function: this function deactivates the control for a maximum of 30 minutes

if there is an open window in the room, thus saving energy.

H. Control operation

1. ON / STANDBY (STAND-BY)

Press the [On / Standby] key to turn on the unit or enter “Standby

Mode”. When active, the set mode and temperature are displayed. Du-

ring “Stand-by” the display shows the On / O󰀨 symbol, the current time

and the day of the week.

NOTE: When the device enters “Standby” mode, 2 beeps of 0.5 se-

conds are emitted. When the device is turned on, it emits two sounds

that last one second.

2. COMFORT / NIGHT MODE

Two di󰀨erent temperature levels can be set:

• “COMFORT” TEMPERATURE: this is the temperature used for “Comfort” and “Chrono” mode.

• “NIGHT” TEMPERATURE: this is the temperature used for the “Night” and “Chrono” modes.

The desired temperature setting can be congured by pressing the [+] and [-] buttons.

The temperature regulation range is between 7 ° C and 30° C.

IMPORTANT!

The “Night” temperature is always lower than the “Comfort” temperature and priority is assigned to

the “Comfort” temperature. For this reason, the “Night” temperature can be set in the range 7 ° C ÷

(“Comfort” - 0.5 ° C), on the contrary, the “Comfort” temperature can be adjusted within the entire

range: (“ Night ”+ 0.5 ° C) to 30°C.

3. OPERATING MODE

Press [Prog] to select the desired mode (see image).

COMFORT MODE

The “Comfort” mode allows you to maintain the set room temperature.

To set this mode:

• Press the [Prog] key until the “Comfort” mode icon appears on the screen.

• Set the desired temperature with the [+] and [-] buttons.

NIGHT MODE

In “Night” mode, a temperature lower than the “Comfort” temperature is set. We recommend using this

mode at night or when the room is not used for 2 hours or more.

To set this mode:

• Press the [Prog] key until the “Night” icon appears on the screen.

• Set the desired temperature with the [+] and [-] buttons.

ANTI-FREEZE MODE

In “ANTI-FREEZE” mode, the temperature is set to 7 ° C. The appliance activates the heating element

when the room temperature drops below 7 ° C.

We recommend using this mode when the room will not be used for several days.

• Press the [Prog] key until the “ANTI-FREEZE” icon appears on the display.

2H TIMER MODE

The “2h Timer” mode can be used to quickly heat the room or speed up the drying of towels.

• Press the [Prog] key until the “2H” icon appears on the screen

The appliance is switched on at maximum power for 2 hours, but the ambient temperature, for safety

reasons, cannot be higher than 30° C. The “2h Timer” mode stops automatically after a period of 2

hours and returns to the previously set operating mode. If necessary, the user can return to other

modes at any time simply by pressing the [Prog] key.

CHRONO MODE

Chrono mode programming

a) Set the current day and time

• Activate the “Standby” mode and press the [Chrono] key for more than 3 seconds.

• The display will show the words: “Ted.”

• Press the [Prog] key to enter the mode. Set the current day with the [+] and [-] keys (1 to 7).

• Press the [Prog] button again to conrm.

The display now shows the current time to be conrmed.

‘Hours’: use the [+] and [-] keys to set the hour and conrm with the [Prog] key.

‘Minutes’: repeat the same procedure and conrm with the [Prog] key.

• At the end, the thermostat returns to “Standby” mode.

b) Set the program for Chrono mode (P4)

• Enter the “Standby” mode and press the [Chrono] key for more than

3 seconds.

• At the top of the screen, you will see the words: “Ted.”

• To congure the “Chrono” mode time sequence, press the [+] key until

the word ‘’ Prog ‘’ (Programming) appears on the screen. [See the

photo on the right].

• Press the [Prog] key to enter the mode.

Now you can set a time sequence for each day of the week.

From day 1, select the desired sequence with the [+] and [-] keys to select, for each hour, between

the “Comfort” temperature button (full bar) [+] and the “Night” temperature key. (empty bar) [-].

Press [Prog] to conrm the setting for the rst day, repeat the same procedure for the remaining 6

days of the week.

c) To use a preset mode (P1 P2 P3) or programmable mode (P4)

Press the [Stand-By / ON] key and exit standby mode, press the [Prog] key

until the symbol appears on the screen.

At the top of the screen, the program in use is shown (from P1 to P4), the

programs are selected by pressing the [Chrono] Key, on the outside of the

screen you can see, for each program, the operation bars time of the indi-

cated program.

Pre-congured programs in Chrono mode

KEYBOARD LOCK

This function allows the user to lock the keyboard to prevent accidental changes. All buttons on the

remote control are locked. To activate the key lock function, press [Prog] for 3 seconds. To deacti-

vate the function, repeat the procedure. As a safety feature, you can always turn o󰀨 the device by

pressing the [on/o󰀨] key, even when the keypad is locked.

OPEN WINDOWS FUNCTION

The device allows detecting the presence of an open window to limit energy consumption, to acti-

vate this mode, activate Standby Mode, press the [Chrono] key for more than 3 seconds, you can

scroll through the modes with the [+] key and select FUNC with the [Prog] key, the window icon will

ash in the upper left corner of the screen, using the [+] key select ON / OFF, visible in the center

of the screen, and conrm with [Prog]. The icon will be active during thermostat operation, if the

open window is detected, the icon will blink and the system will turn o󰀨 the heating for a maximum

of 30 minutes or until a temperature rise of at least 1.5 ° C.

ASC FUNCTION

This function allows you to optimize the operating times of the device, to limit consumption, acti-

vating this mode, the device will record the time necessary to bring a specic room to the specic

temperature, adjusting its operation automatically, in this way the thermostat can be activated later

of a programmed time if it is possible to reach the desired temperature in less time than foreseen by

the operation with the time intervals that have been established. Activate standby mode, press the

[Chrono] key for more than 3 seconds, cycle through the modes with the [+] key and select FUNC

with the [Prog] key, press it until the icon appears at the top of the screen, select ON with

the [+] key and press [Prog] again to conrm. After a few seconds, the remote control automatically

returns to standby mode.

ECO MODE (Function only available via optional remote control)

This mode reduces electricity consumption to 3 ° C (Comfort - 3 ° C). In standby mode, press the

[Chrono] key for more than 3 seconds, scroll with the [+] key and select FUNC with the [Prog] key,

press it until the ECO icon appears, select ON with the [+] button and press [Prog] again to conrm.

After a few seconds, the remote control automatically returns to standby mode.

CONSUMPTION INDICATOR

This useful feature shows the current electricity consumption level depending on the set temperatu-

re. The three coloured icons on the display (green, yellow and red) correspond to low, medium and

high consuption respectively.

Monday-Friday

Weekend

A. Introducción

Siguiendo las indicaciones de este manual de instrucciones, le garantizamos un correcto funcionamiento,

para que pueda disfrutar del producto que ha adquirido durante muchos años. Léalo detalladamente antes

de utilizar el secatoallas y guárdelo en un lugar seguro, le será de utilidad para cualquier consulta.

MUY IMPORTANTE

• Lea el manual de instalación y uso antes de montar y manejar el equipo.

• Observe con detenimiento las advertencias.

• Instale el equipo en un lugar donde pueda circular el aire.

• Es aconsejable que sea montado por personal cualicado

• ADVERTENCIA ¡RIESGO DE DESCARGA ELÉCTRICA!

Desconecte la alimentación antes de continuar con la

instalación.

• Preste atención a la presente hoja de instrucciones y lea

cuidadosamente antes de usar el dispositivo.

• El presente dispositivo ha sido diseñado para uso exclusivo de

toallero.

• El control está diseñado para calentar el líquido contenido dentro

del secatoallas en combinación con un elemento de calefacción.

Cualquier otro uso está prohibido.

• No utilice el toallero para el secado de prendas de composición

sintética o acrílica. Este aparato es sólo para el secado de textiles

lavados en agua. Debe comprobar antes de colocar toallas u otro

tipo de prenda, que esta es capaz de soportar altas temperaturas.

• En el toallero se pueden alcanzar hasta 95 °C de temperatura.

• Cuando utilice el toallero para el secado de toallas, procure no

colocar más de 2 para el caso de los toalleros cuyas potencias

estén comprendidas entre 350-500W ni más de 4 en el caso de

toalleros de cuyas potencias estén comprendidas entre 600-800W

y que éstas no estén superpuestas, es decir, una encima de otra.

• Evitar colocar las toallas encima de los soportes a pared.

• Antes de usar, asegúrese cuidadosamente de que el voltaje

de línea sea el mismo que el especicado para el dispositivo

(consulte las especicaciones técnicas).

• Solo use elementos de calefacción compatibles con el tipo de

seca toallas usado.

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Manuali Stufa popolari di altre marche

oventrop

oventrop Regucor Series Manuale utente

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuale utente

ELMEKO

ELMEKO ML 150 Manuale utente

BN Thermic

BN Thermic 830T Manuale utente

KING

KING K Series Guida

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guida rapida

Well Straler

Well Straler RC-16B Manuale utente

EUROM

EUROM 333299 Manuale utente

Heylo

Heylo K 170 Manuale utente

Eterna

Eterna TR70W Manuale utente

Clarke

Clarke GRH15 Manuale di istruzioni

IRSAP

IRSAP The Radiator Company Ovali Manuale utente

Empire Heating Systems

Empire Heating Systems WCC65 Manuale utente

Wetekom

Wetekom 92 86 43 Manuale utente

Desa

Desa SPC170-F Manuale utente

Watlow

Watlow Watrod Electric Tubular Heaters Manuale utente

Haverland

Haverland ECO-DRY GPS Series Manuale elenco delle parti

Stelpro

Stelpro ASILVC2060 Series Manuale utente