Ten-Tec AT588K Manuale utente
INSTRUCTION MANUAL – MODEL AT588K
Model AT588K is a user-installable kit to add the internal automatic antenna tuner to an
existing model 588 Omni-VII transceiver. Instructions, complete with color photos of
relevant detail, are included in this manual.
Model AT588K is a “no-solder” kit. You will need the following tools:
#10 Torx wrench (provided with the kit, Ten-Tec part #38313).
Small pair of needle nose pliers.
2 Philips screwdrivers, one small, one large.
We recommend you read this manual in its entirety before beginning installation of the
tuner kit.
Should you have difficulty installing the tuner or need advice, our service department is
available to provide technical support from 8 a.m. to 5 p.m. USA Eastern time by calling
(865) 428-0364.
Ten-Tec, Inc., 1185 Dolly Parton Parkway, Sevierville, TN 37862 USA
Sales: (800) 833-7373. General Info and Office: (865) 453-7172.
Service: (865) 428-0364. Visit us on the web at www.tentec.com
Ten-Tec part #74431
Version 1 – February 2009
1. Disconnect transceiver power cable from rear. Remove top and bottom cover.
There are 2 large black Philips screws on each side of the case. Remove these 4 screws.
Around the rear perimeter of the top and bottom covers are #10 Torx screws. Use the
provided Torx wrench to remove them.
Ten-Tec part #74431
Version 1 – February 2009
2. Use caution when removing the top cover from the chassis. The internal speaker
connection wire can be broken off easily if care is not exercised. The speaker wire is
connected to connector 9B just under the external speaker jack as pointed out in the
above photo. Pull the socket off the connector and pull the wire out from the black
grommets. Set top cover with speaker intact aside.
Ten-Tec part #74431
Version 1 – February 2009
3. This is the rear tuner shield, with standoffs already installed to mount the tuner. There
are 4 small black Philips screws holding the plate in place. Remove the first two shown
in each corner here, then turn the radio upside down and remove the remaining two. Turn
the radio right side up after the bottom two are removed.
Ten-Tec part #74431
Version 1 – February 2009
4. This is the view of the rear low pass filter board after the tuner shield has been
removed.
Ten-Tec part #74431
Version 1 – February 2009
5. Remove the autotuner board from the packing kit and place it onto the tuner shield as
shown above. 4 screws, Ten-Tec part #60069 are provided in the packing kit to attach
the tuner board to the shield. There is only one possible correct orientation of the board
to the shield due to the way the standoffs are set on the board. An incorrect installation
will have the circuit board hanging partially off the tuner shield.
Ten-Tec part #74431
Version 1 – February 2009
6. Locate cable #31. This cable is labeled #31 at both ends. One end will be unplugged
by you in this step. The end to be unplugged is shown here, a white cable labeled 31, just
to the right of cable #23 and just above cable #29. With the radio right side up, these
cable ends are located in the middle of the right side of the low pass filter board that was
exposed after the tuner shield was removed in step 3. After unplugging the cable, pull
the unplugged end out from inside of the plastic grommet closest to the socket (shown
here with three additional black cables routed through the same grommet). This cable
will be plugged into the autotuner board in a later step.
Ten-Tec part #74431
Version 1 – February 2009
7. Provided in the packing kit with the tuner board is a cable labeled #32. Route one end
of this cable through the middle grommet as shown above, and plug one end into the
socket that you removed cable #31 from in step 6. Leave the other end unplugged. It
will be plugged into the autotuner board in a later step. Note that the space available to
reach in with your fingers to plug this cable in is limited. We recommend grasping the
connector end with a small pair of needle nose pliers to insert the #32 cable end into the
socket. Picture shown here is with the #32 cable successfully in place of #31.
Ten-Tec part #74431
Version 1 – February 2009
8. Turn the radio upside down. Along the left side of the radio is a multi-wire cable
bundle with an unplugged connector marked 19 on one end that is partially tucked inside
a plastic grommet.
Ten-Tec part #74431
Version 1 – February 2009
9. Pull the #19 cable out from the grommet that was holding it in place as shown in step
8. Unfurl the cable to its full length, then thread the connector end through the two
plastic grommets as shown above. Leave this cable unplugged. It will be plugged into
the autotuner board in a later step.
Ten-Tec part #74431
Version 1 – February 2009
Altri manuali Ten-Tec Ricetrasmettitore
Ten-Tec
Ten-Tec Jupiter 538 Manuale utente
Ten-Tec
Ten-Tec Argonaut 515 Manuale utente
Ten-Tec
Ten-Tec Orion Manuale utente
Ten-Tec
Ten-Tec Pegasus 550 Manuale utente
Ten-Tec
Ten-Tec ORION II Manuale utente
Ten-Tec
Ten-Tec omni V 562 Manuale utente
Ten-Tec
Ten-Tec JUPITER Manuale utente
Ten-Tec
Ten-Tec 555 Manuale utente
Ten-Tec
Ten-Tec 507 Patriot Manuale utente
Ten-Tec
Ten-Tec ARGONAUT VI 539 Manuale utente
Ten-Tec
Ten-Tec Jupiter 538 Manuale utente
Ten-Tec
Ten-Tec ARGONAUT VI 539 Manuale utente
Ten-Tec
Ten-Tec 6N2 Manuale utente
Ten-Tec
Ten-Tec Jupiter 538 Series Manuale utente
Ten-Tec
Ten-Tec R4020 Manuale utente
Ten-Tec
Ten-Tec Eagle 599 Manuale utente
Ten-Tec
Ten-Tec Eagle 599 Manuale utente
Ten-Tec
Ten-Tec 6N2 Manuale utente
Ten-Tec
Ten-Tec REBEL 506 Manuale utente
Ten-Tec
Ten-Tec R4020 Manuale utente
