Tentative 59001 Manuale utente
REVOLUTION DCC SYSTEM
INSTALLATION AND
OPERATION MANUAL
2.4GHz DCC R/C System <TENTATIVE> 1
Revolution DCC Transmitter 'TX'
59001
DCC 5A Command / Booster Station /Mobile
Receiver
59002
15 AMP Station Command/Booster RX
59005
TENTATIVE
1 INTRODUCTION:
Congratulations on your purchase of the Revolution DCC wireless system.
The Revolution-DCC system can be used with any existing NMR compliance standard decoders. This system
is very easy to use because it does not connect to any wire to the command station. It works with IEEE-801.15.4
standard 2.4GHz DSSS radio frequency band for ultimate stability and interference free operation even with the
same frequency channel.
Unlike conventional DCC products, you do not have to remember the complex DCC address of the Locomotive
or ccessory numbers. You only need to select the CAB or ACEES CONT whose Loco or ccessory name
and the DCC address number will be displayed on the TX main LCD screen. The DCC program to the decoder is
very simple, and it is also very convenient because you can read the CV data or DCC address value from the
decoder.
The locomotive and accessory profile data can be stored and recalled up to 2,500 profiles.
Since multiple transmitters can be used on the same layout, they can be used simultaneously with the other
members.
2 OPERATION OVERVIEW:
The Revolution DCC system lets you walk around your model railroad layout and remotely control your
DCC decoder equipped locomotive and DCC accessory such as switch turnouts. Before you start working with
the Revolution DCC System, there are a few concepts that you need to understand about the PROFILE NUM
[1-25]. Each profile number contains all the locomotive or accessory DCC data information to connect the DCC
decoders. Our Transmitter and Receiver are designed to communicate to the DCC decoder in your locomotives
or accessories.
The first concept is to establish a control between the transmitter, receiver and DCC decoder in the locomotive.
You need to set up some basic parameters that define the locomotive or accessory name, DCC address and
other parameters to set the PROFILE NUM [1-25]. Once these parameters are set, you just need to remember
the name of locomotive or accessories. Forget the complex DCC address and other parameters.
The second concept has to do with the Cab and ccessory ssignment once you set parameters to the
PROFILE NUM[1-25].
You must add the PROFILE NUM [n] that the locomotive or accessory will run under the Cab number. Cab
Numbers range from C B-1 through C B25. This allows you to easily move between as many as 25 cab
numbers. There are 100 memory banks in the REVO-DCC Transmitter and each bank can store up to 25
profile numbers, so you will have a total of 2500 Locomotive and accessory profiles numbers. Once you
understand the REVO-DCC system it will be very easy to use and operate. ll menus and setup will displayed on
the LCD screen in simple English text, so no user manual will be needed on hand.
Note: DCC programming modes
There are two primary modes of programming: programming Track (service mode) and
Main(Power On Main) programming mode. The programming track mode requires a programming
track which is isolated electrically. Refer to the wiring diagram in FIG-1 and FIG-3.
2.4GHz DCC R/C System <TENTATIVE> 2
TRANSMITTER
3 FEATURES:
2.4GHz DSSS Duplex Wireless System.
The transmitter can read the decoder's CV value from the receiver.
Radio control range over 500 feet outdoors.
Very easy DCC programming without complex engineering knowledge
DCC programming is done in simple English text.
No need to remember the locomotive or accessory DCC address number, simply choose the name of
the given locomotive or accessory C B # or CONTROL #.
Multi-unit operation ( dvanced Consist) settings are very simple.
Single button controls multi-accessory (turnover) devices.
2,500 locomotive and 2,500 accessory separate memory slots are provided.
CV program range: CV1 to CV1024 (Function and ccessory decoder).
Decoder address program range: Short (2digits) 1-127 and Long(4 digits) 1-9999.
ccessory ddress program range: 1-2044.
Easy access speed steps 28 or 128.
Easy access F1 to F28 function control.
Easy to TX clone.
Single button for all stop function.
RX DCC OUTPUT POWER ON/OFF Control.
Exchange data from TX to TX.
The firmware can be upgraded wirelessly.
RECEIVER
4 FEATURES:
2.4GHz DSSS duplex radio system.
Radio control up to 500 feet at open air.
High efficiency synchronous DCC Booster.
DCC Command Station-Booster RX for N, HO,O, S, G scale track or mobile setup.
Works with any NMR -DCC multi-function / accessory / sound decoders.
Wide input voltage up to 24V DC.
Maintains 2500 locomotives and 2500 accessories.
Programmable output current and power limit.
Wireless firmware upgrade-able.
2.4GHz DCC R/C System <TENTATIVE> 3
DIAGRAM FOR RECEIVER INSTALLATION SET UP
5A DCC RX TRACK POWER MODE
DIAGRAM FOR BATTERY INSTALLATION SET UP
2.4GHz DCC R/C System <TENTATIVE> 4
(FIG-1)
(FIG-2)
DIAGRAM FOR TRACK INSTALLATION SET UP
15A DCC STATION BOOSTER RX TRACK POWER MODE
Note:
Power source for N ,HO, S: 12 – 15V DC
Power source for O,G :15 – 24V DC
Key-Pad letter Functions
<<T C B # decrease
T>> C B # increase
STOP Stop/Enter
▲ Increase Speed
▼ Decrease speed
◄ Direction change
► Direction change
sterisk Quick Program
Qiuck menu
(0) all stop Function Control
Emergency all stop
MENU Select menu
1--9 Function control
ON/OFF Power ON/OFF
TRANSMITTER KEYPAD LABEL
2.4GHz DCC R/C System <TENTATIVE> 5
(FIG-3)
There are three concepts how to use the Revolution-DCC R/C System that need to be understand.
Refer to the LCD screen menu descriptions for details.
2.4GHz DCC R/C System <TENTATIVE> 6
SELECT MODE BANK: 35
1) LOCO CONT/ROL
2) ACCESSORY CONTROL
3) SET UP
(FIG- )
LCD Screen view items vs specific functions
LOCO CONTROL LCD SCREEN ACCESSORY CONTROL LCD SCREEN
:①Radio signal strength Icon :①Radio signal strength Icon
:②Receiver ID number : ②Receiver ID number
:③Profile Number(at Consist mode in UNI or DV, it shows UNI or ADVnnn) : ③ccessory control link number
④:Locomotive name : ④ccessory (Turnout) name
⑤ :DCC ddress number (short 3digit or long-4digit) : ⑤ccessory profile number[1---25]
⑥ :DCC function F0-F28 activation status : ⑥DCC ccessory address(1-2044)
⑦ :Locomotive speed :⑦TX Battery icon
⑧ :TX Battery icon :⑧TX Battery voltage
⑨ :TX battery voltage :⑨RX Radio Link and fault status
⑩ :RX Radio Link and fault status :⑩RX input power voltage
⑪ :RX input power voltage : ⑪ccessory control select to “ON” or “OFF”.
⑫ :Locomotive direction :⑫Multi accessory control mode(single or multi mode)
⑬: DCC speed step( 28 or 128 step) N/
⑭ : ctive locomotive number in the current C B number N/
⑮ :Current C B number (S:consist mode off ; C:consist mode on) N/
TX MAIN LCD SCREEN: (FIG 4)
When the power is turned ON, three operation menus will be displayed.
Press ▲ button or ▼button to scroll up or down to select the desired menu then press the STOP button to select
that function. For more information, see the corresponding menu descriptions.
Press the [MENU] button to return.
LOCO CONTROL:
Single or consist locomotive can be controlled under the selected C B number.
You can change the C B number by pressing the [<<T] or [T>>] buttons and all of the locomotive information will
be displayed on the LCD screen such as the Locomotive name , DCC address, and locomotive consist mode.
For more information, see the corresponding menu descriptions.
Press the [MENU] button to return.
ACCESSORY CONTROL:
The accessory will be controlled with very simple programming and the accessory DCC parameters will be
stored to the each profile number so you just select the accessory name rather than the complex DCC address
number. For more information, see the corresponding menu description.
Press the [MENU] button to return.
SET UP:
Various parameters can be set on the SET UP menu screen. For more information, see the corresponding menu
descriptions.
Press the [MENU] button to return
2.4GHz DCC R/C System <TENTATIVE> 7
(Table-1)
LOCO CONTROL: (SCREEN-A)
Press [ <<T ]” or “ [ T>> ] to select to desired C B number.
Increase speed: Press the [UP arrow] button.
Decrease speed: Press the [DOWN arrow] button.
Locomotive direction change: Press the [LEFT arrow] or [RIGHT
arrow] button. To change the speed step go to the QUICK MENU.
If Transmitter is successfully linked to the receiver, the link status
should be displayed LINKOK on the display screen item ① and ⑩
.
If the C B number is selected (1) and it was selected to the consist
mode it should display C B-1C otherwise C B-1S.
Display item number ③
Consist OFF mode: display PROFI-n (n=Profile number ,1 to 25)
Consist UNI mode: display UNI-CON
Consist DV mode: display ADVnnn (nnn= dvanced consist short
address number)
QUICK PROGRAM: (SCREEN-B)
While operating in the LOCO CONTROL mode, press the [ * ] button.
Then the screen will be changed to the “QUICK PROGRAM” mode.
Press the MENU button to exit.
a) ACCELERATION (CV3)
Press the number buttons between 0 to 255 and then press the STOP
button.
b) DECELERATION (CV4)
Press the number buttons between 0 to 255 and then press the STOP
button.
c) PROGRAM:
Press STOP button then the LCD screen will be changed
LOCO PROGRAM menu screen.
d) RX STATION POWER LIMIT:
This value is for maximum RX power value. It can be changed from 25%
to 100%. Press LEFT arrow button to decrease and RIGHT arrow button to increase
the value. The default power value is 75%.
LOCO PROGAM MODE: (SCREEN-C)
There are two types of DCC programming mode.
(a) PROG MODE:
Press [STOP] button to toggle between TR CK or M IN function.
TRACK (Service mode) PROGRAMMING :
Press the [STOP] button, if successfully written the data to the decoder then
the LCD shows “ CK OK”
(Note: The locomotive must laced on the rogramming track)
2.4GHz DCC R/C System <TENTATIVE> 8
SCREEN-A
SCREEN-B
SCREEN-C
MAIN – PROGRAMMING (OPS) MODE:
Press the [STOP] button and the LCD will “SENT PACKT”.
(Note: The locomotive must have the same DCC address with the TX packet DCC address).
(b) CV NUMBER:
Press the number buttons to set the desired DCC CV address number.
(c) CV VALUE:
Press the number button to set the desired DCC CV value address number
(d) READ:
This function is only active in the TR CK programming mode.
Press the [STOP] button, then wait until the reading value displayed on the LCD screen.
(NOTE: To read the locomotive it must be on the programming track)
(e) WRITE:
This function allows to send the programming packet to a receiver.
Press the MENU button to exit
QUICK MENU: (SCREEN-D)
While operating in the LOCO CONTROL mode, simply press the [ ]
button.
Then the screen view will be changed to the “QUICK MENU” mode as
shown on screen D.
Press the MENU button to exit.
a) LOCO:
You can select the locomotive that you are currently using in the C B consisting
mode. Press◄ or ► button to select the desired Loco-number.
b) FUNC x10 DIGIT:
This number is the 10's digit of the function(F0-F28) control number.
Digit 0: select to control F0-F9
Digit 1: select to control F10-F19
Digit 2: select to control F20-F28
Press◄ or ► button to select the desired 10's digit function.
c) SPEED STEPS:
This function allows to select the DCC speed step(28 or 128 speed step).
Press◄ or ► button to select the desired DCC speed step.
d) RX ID NUMBER:
You can select the RX ID # 1 to 10 to link the receiver.
Press◄ or ► button to select the desired receiver number.
2.4GHz DCC R/C System <TENTATIVE> 9
SCREEN-D
ACCESSORY CONTROL SCREEN: (SCREEN-E)
ccessory Control: (Switch Turnout )
Press [<<T] or [T>>] to select to desired the CCESS LINK number.
Press ◄ or ►button to select [ON] or [OFF].
Press [STOP] button on TX and the LCD will displays “SENT
P CKET”
The control packet will be sent to the RX.
Note: If multi link mode is selected the LCD display item ⑫ will
displays “MULTI LINK”.
You can control up 8 turnout switches by single click.
(refer to the “ CCESSORY SSGN” - SCREEN-15 menu)
QUICK MENU SCREEN: (SCREEN-F)
While operating in the ACCESSORY CONTROL mode, press the [ * ] button.
Then the screen will be changed to the “QUICK PROGRAM” mode.
Press the MENU button to exit.
ACCESS PROGRAM
(a) CV NUMBER:
Use the keypad to type numbers to set the CV number.
(b) CV VALUE:
Use the keypad to type numbers to set the CV value.
(c) WRITE:
fter select CV number and CV value, press the [STOP] button on the TX to
write the accessory decoder.
2.4GHz DCC R/C System <TENTATIVE> 10
SCREEN-1
SCREEN-E
SCREEN-F
Questo manuale è adatto per i seguenti modelli
2
Indice
Manuali Sistema microfonico popolari di altre marche
Sennheiser
Sennheiser Evolution Wireless Digital EW-DX EM 2 Manuale utente
Alpha Technologies
Alpha Technologies RBMS Manuale utente
SWIT Electronics Co.,LTD.
SWIT Electronics Co.,LTD. CW-S150 Manuale utente
Shure
Shure UA844 Manuale utente
Panasonic
Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manuale utente
Pyle
Pyle PDWM5000 Manuale utente