Terex TECH TIP 31 Manuale utente

TEREX UTILITIES TECHNICAL SUPPORT TEAM

PHONE: 1-844-TEREX4U (1-844-837-3948) | EMAIL: [email protected]

MODEL(S): TOOLS NEEDED:SERVICE CALL:

NO.

PROGRAMMING TEH MOTOR

CONTROLLER ON A 48V

HYPOWERTM

ALL TEREX UTILITIES UNITS

EQUIPPED WITH THE 48V

HYPOWERTM SYSTEM

CURTIS PROGRAMMING DEVICE

PHILLIPS SCREWDRIVER

PROGRAMMING THE MOTOR CONTROLLER ON A 48V HYPOWERTM

DANGER

Failure to obey the instructions and safety

rules in the appropriate Operator’s Manual and

Service Manual for your machine will result in

death or serious injury.

Many of the hazards identied in the

Operator’s Manual are also safety hazards

when maintenance and repair procedures are

performed.

DO NOT PERFORM

MAINTENANCE UNLESS:

√You are trained and qualied to perform

maintenance on this machine.

√You read, understand and obey:

•manufacturer’s instructions and safety rules

•employer’s safety rules and worksite

regulations

•applicable governmental regulations

√You have the appropriate tools, lifting

equipment and a suitable workshop.

The information contained in this Tech Tip is a

supplement to the Service Manual. Consult the

appropriate Service Manual of your machine for

safety rules and hazards.

PAGE 2 OF 10

TECH TIP 31 | RELEASED 03.14.2022 | VERSION 1.0

PAGE 3 OF 10

CONTENTS

TECH TIP#31

4| Boot up the system

| Locate the panel

STEP 1 - STEP 2

5| Remove the connector

| Select parameters

STEP 3 - STEP 4

7| Set Turn On Time Threshold

| Select Motor Item in Parameters

STEP 5 - STEP 6

9| Adjust speed settings

| Verify programming

STEP 7 - STEP 9

TECH TIP 31 | RELEASED 03.14.2022 | VERSION 1.0

STEP 1

Boot up the 48V system, consult the operator’s manual for operational instructions.

STEP 2

Locate the panel displaying PTO hours and hybrid battery status. This panel is typically installed in

one of the rear compartments. Once the panel has been located, remove the four Phillips screws

holding it in place.

PAGE 4 OF 10

TECH TIP 31 | RELEASED 03.14.2022 | VERSION 1.0

STEP 3

Remove the connector at the back of the battery display and connect it to the Curtis Programming

Device. After approximately 10 seconds, the Curtis Programming Device should power up.

STEP 4

Once the system boots up, use the arrow keys to select the Parameters menu.

PAGE 5 OF 10

TECH TIP 31 | RELEASED 03.14.2022 | VERSION 1.0

STEP 4 (CONTINUED)

Next select Output Parameters.

The variable, Turn on Voltage should be set to 44.50V. This value represents the voltage that

triggers the engine to start and recharge the unit. If this value is incorrect, use the arrow keys to

select it and change the set value.

PAGE 6 OF 10

TECH TIP 31 | RELEASED 03.14.2022 | VERSION 1.0

STEP 5

Next look at the variable, Turn On Time Threshold. This threshold is the amount of time that the

voltage must stay below the 44.50V before the system starts to recharge. This value should be set to

5 seconds, select it to modify the set value.

STEP 6

Select the Motor menu item in the parameters menu.

PAGE 7 OF 10

TECH TIP 31 | RELEASED 03.14.2022 | VERSION 1.0

STEP 6 (CONTINUED)

Next, choose Temperature Control.

The Sensor Enable variable in this screen should be set to OFF. If it is ON, select the variable to

modify it.

PAGE 8 OF 10

TECH TIP 31 | RELEASED 03.14.2022 | VERSION 1.0

STEP 8

Nothing needs to be done to save changes, the

modications are made immediately.

STEP 7

To adjust the speed settings, select the

Programming menu, Speed Settings, and then

RPM mode 1. Set the RPM to produce 5 GPM at

1800 psi. Then select RPM mode 2 and set it to

get 7 GPM at 1800 psi.

For units with single ow hydraulics, set RPM

mode 2 to get the required ow (5 or 7 GPM) at

1800 psi.

STEP 9

To verify the programming, operate the unit in

hybrid mode until the batteries reach 44.5 Volts.

Once the voltage remains at or below 44.5 V for

at least 5 seconds the chassis engine should

start to charge the hybrid system.

PAGE 9 OF 10

FOR FURTHER ASSISTANCE,

CONTACT THE TEREX UTILITIES TECHNICAL SUPPORT TEAM

PHONE: 1-844-TEREX4U (1-844-837-3948) | EMAIL: [email protected]

Altri manuali Terex Piattaforma aerea

Terex

Terex Genie Z-80 Manuale di installazione e funzionamento

Terex

Terex ZX13515-2558 Manuale utente

Terex

Terex SX15015-101 Manuale utente

Terex

Terex S85XCH-3740 Manuale utente

Terex

Terex Genie GTH -1056 Manuale di installazione e funzionamento

Terex

Terex Genie S-100HD Manuale di installazione e funzionamento

Terex

Terex Genie Z-30N Manuale di installazione e funzionamento

Terex

Terex S8015-12264 Manuale di installazione e funzionamento

Terex

Terex Genie Z-34/22 IC Manuale di installazione e funzionamento

Terex

Terex Genie S-60XC Manuale di installazione e funzionamento

Terex

Terex C5000 Series Manuale utente

Terex

Terex Genie Z-45 FE Manuale utente

Terex

Terex Genie Z62D-150 Manuale utente

Terex

Terex Genie S-40 Trax Manuale utente

Terex

Terex Z60H-3506 Manuale utente

Terex

Terex Genie Z-34 IC Manuale di installazione e funzionamento

Terex

Terex Genie Z-33/18 Manuale di installazione e funzionamento

Terex

Terex Genie Z-34/22 Manuale di installazione e funzionamento

Terex

Terex Genie Lift Guard S-40 Manuale utente

Terex

Terex Genie Z-60 DC Manuale utente

Terex

Terex Genie Z-60/37 DC Manuale di installazione e funzionamento

Terex

Terex Genie Z-45XC Manuale utente

Terex

Terex Genie Z4525XCM-2501 Manuale utente

Terex

Terex Genie Z-25J Manuale utente

Manuali Piattaforma aerea popolari di altre marche

Genie

Genie Z-80 Manuale utente

Genie

Genie Z-45/25 Manuale utente

JLG

JLG Skytrak 6036 Manuale per l'uso e la cura

LGMG

LGMG T65JE Manuale utente

Genie

Genie Z-135/70 Manuale utente

Oshkosh Corporation

Oshkosh Corporation JLG H800AJ Manuale per l'uso e la cura

Oshkosh

Oshkosh JLG 1500SJ Manuale di installazione e d'uso

Skyjack

Skyjack SJ30AJE Manuale utente

Oshkosh

Oshkosh JLG 800A Manuale di installazione e d'uso

Skyjack

Skyjack SJ 46AJ Manuale utente

Molift

Molift Quick Raiser 205 Manuale utente

Snorkel

Snorkel SL26RTE Guida rapida

Oshkosh Corporation

Oshkosh Corporation JLG E300A Manuale utente

Skyjack

Skyjack SJ45 T+ Manuale utente

Genie

Genie S-105 Manuale utente

nifty

nifty 170SD series Istruzioni per il montaggio

JLG

JLG 15MVL Series Manuale utente

Genie

Genie Z-45 XC Manuale utente