Tescom XC Series Manuale utente

XC SERIES

1 kVA

ON-LINE

NINTERRUPTIBLE

OWER

UPPLIES

USER

MANUAL

CONTENTS

I. INTRODUCTION

1.1 System Description ................................................................. 1

1.2 Technical Specifications ......................................................... 2

1.3 Physical Specifications ........................................................... 2

II. SETTING UP YOUR UPS

2.1 Unpacking ............................................................................... 3

2.2 Location Selection................................................................... 3

2.3 Installation ............................................................................... 3

2.4 Start–up................................................................................... 4

III. OPERATION PROCEDURE

3.1 Turn On Procedure ................................................................. 5

3.2 Turn Off Procedure ................................................................. 5

3.3 When Utility Power Is Interrupted ........................................... 5

3.4 Manuel Battery Test System................................................... 6

IV. CUSTOMER SERVICE

4.1 Maintenance............................................................................ 7

4.2 LCD Display ........................................................................... 8

4.3 Error Codes............................................................................ 9

V. LIMITED WARRANTY ................................................................... 10

IMPORTANT NOTICES

1 . Read instructions carefully before operating the UPS

2 . All warnings in the manual should be adhered to.

3 . All operating instructions should be followed.

4 . The unit should be supplied by a grounded outlet.

DO NOT operate the unit without ground source .

5 . Power cord of the UPS should be routed carefully so that they are not to be walked on.

WARNING

1 . DO NOT OPEN THE COVER. THERE ARE NO USER SERVICEABLE PARTS

INSIDE.

2 . DO NOT INSERT ANY OBJECT INTO VENTILATION HOLES OR OTHER

OPENINGS.

3 . INTENDED FOR INSTALLATION IN A PROTECTED ENVIRONMENT.

XC Series 1kVA User Manual

I. INTRODUCTION

1.1 System Description

XC Series Uninterruptible Power Supplies are advanced true On-Line Sinewave UPS with static

transfer switch which provide reliable, regulated, transient-free AC power to sensitive equipment,

ranging from computers, telecommunication systems to computerized instruments.

Because the UPS is a true On-Line system, conditioned power is provided continuously to the

connected equipments. Unlike standby power systems, the UPS is constantly regulating and

filtering the output power. When incoming power is interrupted, the UPS protects the computers

instantaneously without any transfer time.

The XC Series has high nonlinear load capability (i.e. Crest Ratio 3:1) and this is suitable for

powering special loads such as switching power supplies or highly capacitive inputs.

The system's static transfer switch (S.T.S) provides by-pass power as its standby source. During

an overload condition, the S.T.S will switch the customer's load over to the bypass line with no

interruption. The S.T.S will transfer back to the inverter automatically when the overload condition

has been cleared. If the inverter fails internally, the unit switches to bypass within milliseconds.

To choose the XC Series as your equipment protector was a wise investment.

It includes many features to protect your critical equipments:

Full Protection

- Built-in battery to protect from power outage

- S.T.S to protect when UPS fails

- On line operation to condition output continuously

- Sinewave output waveform

High Nonlinear Load Capacity

- Special for Computers

Easy operation and installation.

Battery

Inverter

PFC & Rectifier

Static By-Pass

Static Transfer Switch

Input

Output

Charger

DC / DC

Converter

Figure 1.1 Ups Block Diagram

XC Series 1kVA User Manual

1.2 Technical Specifications

XC-101

Output Power

(pf 0.7)

1 kVA - 700W

INPUT

Voltage 220 Vac or 230Vac 1 Ph+N ±20%

Frequency 50 Hz. ±5 %

Cur

rent

6 A

Power Factor

>=0,9

OUTPUT

Voltage

220 Vac or 230Vac

Voltage tolerance ±1%

Frequency

50 Hz.

Frequency tolerance Free running ±0,2 %

Line synchronized ±1 %

Efficiency (100% Load)

88 %

Crest factor

3:1

Overload capacity

100%-125% load 1 min

125%-150% load 10 sec

>150% direct by-pass

Batteries

3 x 12 V

Floating charge voltage

41 Vdc

End of discharge voltage

30 Vdc

Operating temp. 0-40 °C

Automatic battery testing

Optional

1.3 Physical Specifications

Operating Temperature 0

C - 40

Humidity 90%

Altitude max. 1000 meter

Dimensions (HxWxD) 250x160x445 mm

Dry Contacts and

RS232 connections

PK1

On-Off

Switch

AC Input

220/230V 50Hz

AC Output

220/230V 50Hz

Input

Fuse

Figure 1.2 Rear View

Reverse line

polarity indicator

XC Series 1kVA User Manual

II. SETTING UP THE UPS

2.1 Unpacking

The UPS is packed and enclosed in a structural cardboard carton to protect it from danger.

1. Inspect for damage that may have occurred during the shipment If any damage is

noted, call the shipper immediately and retain the shipping carton and the UPS.

2. Carefully open the carton and take the UPS out.

3. Retain the carton and packing material for future use.

2.2 Location Selection

The UPS is designed to be installed in a protected environment. The following conditions should be

prohibited.

1. Blocking the airflow intake and outlet. (It is recomended to retain 10 cm.(4 in.)

between the rear side and the wall.)

2. Environment temperature and humidity out of specification.

3. Location subject to excessive moisture, dust and corrosion.

4. Location exposed to heat source or direct sunlight.

2.3 Installation

It is recomended that the UPS should be connected to a dedicated outlet protected by a circuit

breaker. The UPS has a built in power cord with a ground and 2 receptacles on the rear panel.

1. Make sure that the on-off switch the rear panel is in the "0" position.

2. Plug in the input power cord to a wall outlet.

3. If the “Reverse Line Polarity Indicator” is on, reverse the AC input phase and neutral lines.

4. Turn on the On-Off Switch, into “1” on position.

WARNING : DO NOT DEFEAT GROUND CONNECTIONS

XC Series 1kVA User Manual

2.4 Start-Up

1. Turn on the on-off switch on the rear panel to "1" .

2. The red LED indicator "BYPASS" should light on.

3. In a few seconds the cooling fan will start to operate, then the "BYPASS” indicator will be off

and the green LED indicator "UPS" will turn on and will start to give the UPS power to the

output.

4. Disconnect the input power cord from the power outlet. The "LINE FAILURE" will appear on

the LCD panel and audible alarm will sound intermittently. Now the load is supplied from the

battery source.

5. Plug in the power cord again and see that "LINE FAILURE"alarm is off.

6. Now your UPS is ready to operate. Plug in the critical loads to the output receptacles of the

unit.

NOTE

If any condition is different from the above situation, call our local service representative for

assistance.

CAUTION

After initial start-up, keep power continuously to the unit for at least 8 hours to ensure that the

batteries are fully charged.

XC Series 1kVA User Manual

III. OPERATION PROCEDURE

3.1 Turn On procedure

1 . Turn On the PK1 on-off switch on the rear panel to "I" position.

2 . Turn on the power switches on your critical load after the "UPS" indicator will light on.

3.2 Turn Off procedure

1. Turn off all the power switches on your critical equipments that are connected to the UPS.

2. Turn Off the PK1 on-off switch on the rear panel to "0" position.

CAUTION

A . The UPS charges its battery whenever it is connected to utility power.

B . For daily TURN ON / TURN OFF operation , it is recommended to keep the on to ensure

proper battery operation.

WARNING:

When the UPS connected to utility power, the line power will be supplied to output receptacles

directly. DO NOT insert objects other than equipment power cords into outlets.

3.3 When utility power is interrupted

In case the utility power is interrupted, the UPS converts the built-in battery source to output

receptacles immediately to protect your critical loads from loss of data or damage. Battery

back-up time is 10 minutes for full load and can be extended by removing non-critical loads.

After an utility power blackout, the audible alarm and "LINE FAILURE "will appear on the LCD

panel. When the "BATTERY LOW" alarm will appears you have to shut down all your loads

immediately.

CAUTION

A. Follow the application sofware in use as well as the computer manufacturer's

instructions for saving data and turning off the computer.The remaining of battery

discharge will be enough for you to complete the job.All computer operations

should be terminated as soon as possible.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Tescom UPS

Tescom

Tescom DS300HB Series Manuale utente

Tescom

Tescom MTI200 Series Manuale utente

Tescom

Tescom TEOS 400 FLEX RT Manuale utente

Tescom

Tescom DS3100HT Manuale utente

Tescom

Tescom DS300HT Series Manuale utente

Tescom

Tescom DS300SHP Series Manuale utente

Tescom

Tescom DS POWER H Manuale utente

Tescom

Tescom DS3100 Manuale utente

Tescom

Tescom T-3250P Manuale utente

Tescom

Tescom DS310HA Manuale utente

Tescom

Tescom TEOS 300RT Manuale utente

Tescom

Tescom NEOLINE PLUS 1102ST Manuale utente

Tescom

Tescom DS300H Series Manuale utente

Tescom

Tescom CL110D Manuale utente

Tescom

Tescom DX3000 Series Manuale utente

Tescom

Tescom DS3100A Manuale utente

Tescom

Tescom DS310HT Manuale utente

Tescom

Tescom NEOLINE 1000 Manuale utente

Tescom

Tescom DS3250A Manuale utente

Tescom

Tescom TEOS 200E PRO 10-20kVA Manuale utente

Tescom

Tescom TEOS+ 300 Series Manuale utente

Tescom

Tescom DS330H Manuale utente

Tescom

Tescom DS340H Manuale utente

Tescom

Tescom DS300 HYB Series Manuale utente

Manuali UPS popolari di altre marche

Pylontech

Pylontech Victron & Pylontech US5000 Manuale utente

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuale utente

Mecer

Mecer ME-1000-WTU Manuale utente

Mustek

Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento

Emerson

Emerson Liebert NXL series Manuale utente

MAKELSAN

MAKELSAN BOXER SERIES Manuale utente

Block

Block PC-0524-400-0 Manuale utente

CyberPower

CyberPower CP585LCD Manuale utente

Eaton

Eaton 3S Istruzioni per il montaggio

CyberPower

CyberPower Office Tower Series UPS 1000 Manuale utente

CyberPower

CyberPower BM100 Manuale utente

Best Power

Best Power 610 Manuale utente

Best Power

Best Power Unity/I UT3K Manuale utente

Mustek

Mustek PowerMust 400 Offline Manuale utente

Xantrex

Xantrex Trace 512 UR-UPS Manuale utente

Forza

Forza SL-1501UL Manuale utente

LEGRAND

LEGRAND keor 310081 Manuale utente

ABB

ABB Conceptpower DPA 500 Manuale utente