Tews Technologies TA900 Manuale utente
The Embedded I/O Compan
y
TA900
Program and Debug Box
Version 1.0
User Manual
Issue 1.0.1
July 2012
TEWS TECHNOLOGIES GmbH
Am Bahnhof 7 25469 Halstenbek, Germany
Phone: +49 (0) 4101 4058 0 Fax: +49 (0) 4101 4058 19
e-mail: [email protected] www.tews.com
TA900 User Manual Issue 1.0.1 Page 2 of 12
TA900-10R
Program and Debug Box, USB and JTAG
Connectors, extended temperature range
(RoHS compliant)
This document contains information, which is
proprietary to TEWS TECHNOLOGIES GmbH. Any
reproduction without written permission is forbidden.
TEWS TECHNOLOGIES GmbH has made any
effort to ensure that this manual is accurate and
complete. However TEWS TECHNOLOGIES GmbH
reserves the right to change the product described
in this document at any time without notice.
TEWS TECHNOLOGIES GmbH is not liable for any
damage arising out of the application or use of the
device described herein.
Style Conventions
Hexadecimal characters are specified with prefix 0x,
i.e. 0x029E (that means hexadecimal value 029E).
For signals on hardware products, an ‚Active Low’ is
represented by the signal name with # following, i.e.
IP_RESET#.
Access terms are described as:
W Write Only
R Read Only
R/W Read/Write
R/C Read/Clear
R/S Read/Set
¤2011-2012 by TEWS TECHNOLOGIES GmbH
All trademarks mentioned are property of their respective owners.
TA900 User Manual Issue 1.0.1 Page 3 of 12
Issue Description Date
1.0.0 Initial issue June 2011
1.0.1 General revision July 2012
TA900 User Manual Issue 1.0.1 Page 4 of 12
Table of Contents
1 PRODUCT DESCRIPTION ........................................................................................... 6
2 TECHNICAL SPECIFICATION ..................................................................................... 7
3 CONFIGURATION ........................................................................................................ 8
3.1 JTAG Configuration........................................................................................................................8
3.2 LED Configuration ..........................................................................................................................9
4 DRIVERS.......................................................................................................................9
5 PIN ASSIGNMENT – I/O CONNECTOR ..................................................................... 10
5.1 Front I/O .........................................................................................................................................10
5.1.1 USB B-type Receptacle ..........................................................................................................10
5.1.1.1 Pin Assignment..................................................................................................................10
5.1.2 JTAG Header ..........................................................................................................................11
5.1.2.1 Pin Assignment..................................................................................................................11
5.2 FPC Connector ..............................................................................................................................12
5.2.1 Pin Assignment .......................................................................................................................12
TA900 User Manual Issue 1.0.1 Page 5 of 12
List of Figures
FIGURE 1-1 : BLOCK DIAGRAM......................................................................................................................6
FIGURE 5-1 : TA900 FRONT I/O....................................................................................................................10
FIGURE 5-2 : USB B-TYPE RECEPTACLE VIEW.........................................................................................10
FIGURE 5-3 : JTAG HEADER VIEW ..............................................................................................................11
FIGURE 5-4 : FPC CONNECTOR VIEW ........................................................................................................12
List of Tables
TABLE 2-1 : TECHNICAL SPECIFICATION.....................................................................................................7
TABLE 5-1 : USB B-TYPE RECEPTACLE DETAILS .....................................................................................10
TABLE 5-2 : PIN ASSIGNMENT USB B-TYPE RECEPTACLE .....................................................................10
TABLE 5-3 : JTAG HEADER DETAILS...........................................................................................................11
TABLE 5-4 : PIN ASSIGNMENT JTAG HEADER...........................................................................................11
TABLE 5-5 : FPC CONNECTOR DETAILS ....................................................................................................12
TABLE 5-6 : PIN ASSIGNMENT FPC CONNECTOR ....................................................................................12
TA900 User Manual Issue 1.0.1 Page 6 of 12
1 Product Description
The TA900 is an Interface Box which can be used to program and debug hardware modules providing a
corresponding connector.
The Interface Box connects to compatible modules via a 20-pin Flexible Printed Circuit (FPC) Connector
which can provide access to the module's JTAG Chain and the additional interfaces A and B. The TA900 can
be accessed by USB 2.0 and by a 14-pin JTAG Header, and is equipped with a Pushbutton Switch which is
offering the possibility to send an impulse to one of the connected module's I/O pins. A green LED indicates
the assertion of this impulse by interrupting illumination.
In case of the user programmable FPGA boards TAMC631 and TAMC640/641, Interface A provides access
to the UART of the onboard Module Management Controller (MMC), and Interface B connects to two user
pins of the module's onboard FPGA. If a UART core is implemented in the module's FPGA, serial
communication via Interface B is possible. By setting DIP Switches, the provided yellow LEDs located in the
TA900 front panel can either indicate the logic level of the Interface's lines or can be configured to visualize
serial communication on the Rx and Tx lines, if they are connected to the UART interfaces of the USB
Controller. Level Shifters can handle I/O voltages between 1.2V and 3.3V at the FPC Connector which offers
a wide range of possible configurations for Interface A, B and the JTAG Chain of the connected hardware
module.
The JTAG Chain of the connected hardware module which is useful to program and debug onboard devices
can be accessed in two different ways: If it is accessed via the 14-pin Header, which must be the case when
communicating with Xilinx Devices, a "Xilinx Platform Cable USB II" (which is required) can be connected
without any adaption. If the JTAG Chain is accessed via the USB interface, Channel A of the USB Controller
is not used to communicate with Interface A, but to generate JTAG signals for debugging or programming
reasons. In this configuration, Lattice Devices for example can directly be programmed without the necessity
of an additional Programming Cable, as the TA900 is directly supported by Lattice's Software Tool "ispVM".
The TA900 is self-powered by the FPC Connector which means that it is not necessary to connect the
Interface Box to USB to provide a supply voltage. The Interface Box meets the requirements to operate in
extended temperature range from -30° to +75°C and comes with a USB A to USB B Cable and an FPC
Flexcable.
Figure 1-1 : Block Diagram
TA900 User Manual Issue 1.0.1 Page 7 of 12
2 Technical Specification
FPC Connector Interface
Mechanical Interface 20-pin Flexible Printed Circuit (FPC) Connector
(Tyco 2-84953-0 or compatible)
Electrical Interface JTAG Interface
Interface A
Interface B
User I/O pin BUTTON
I/O Voltages 1.2V to 3.3V
On Board Devices
USB to UART/JTAG Controller FT2232H (FTDI Chip)
USB Interface
Mechanical Interface USB B Receptacle
(Kycon KUSBX-BS1N-W or compatible)
Electrical Interface USB 2.0 High Speed (480Mb/s) and Full Speed (12Mb/s)
(Self-Powered)
0x0403
Vendor ID
Product ID 0x6010
Interface A UART / MPSSE Mode JTAG
Supported by "Lattice ispVM"
Interface B UART
JTAG Header Interface
Mechanical Interface 14-pin Shrouded Header
(Molex 87833-1420 or compatible)
Electrical Interface VREF, GND, TCK, TMS, TDI, TDO
Matches the "Xilinx Platform Cable USB II" pinout
Physical Data
Power Requirements 120mA maximum @ +3.3V DC
Temperature Range Operating
Storage
-30°C to +75°C
-30°C to +75°C
MTBF 639000 h
MTBF values shown are based on calculation according to MIL-HDBK-217F and
MIL-HDBK-217F Notice 2; Environment: GB 20°C.
The MTBF calculation is based on component FIT rates provided by the
component suppliers. If FIT rates are not available, MIL-HDBK-217F and
MIL-HDBK-217F Notice 2 formulas are used for FIT rate calculation.
5 – 95 % non-condensing
Humidity
132 g
Weight
139.7mm x 82.6mm x 26.2mm
Size
Table 2-1 : Technical Specification
TA900 User Manual Issue 1.0.1 Page 8 of 12
3 Configuration
To modify the LED Configuration and the JTAG Configuration remove the PCB Compartment
Door and set the DIP Switches and the Rotary Selector Switch accordingly.
3.1 JTAG Configuration
The JTAG Chain of the connected hardware module which is useful to program and debug onboard devices
can be accessed in two different ways:
If it is accessed via the 14-pin Header, which must be the case when communicating with Xilinx Devices, a
"Xilinx Platform Cable USB II" (which is required) can be connected without any adaption.
If the JTAG Chain is accessed via the USB interface, Channel A of the USB Controller is not used to
communicate with Interface A, but to generate JTAG signals for debugging or programming reasons. In this
configuration, Lattice Devices for example can directly be programmed without the necessity of an additional
Programming Cable, as the TA900 is directly supported by Lattice's Software Tool "ispVM".
Whether the JTAG Chain of the module connected to the FPC Connector is accessed by the JTAG Header
or by USB is determined by the configuration of the Rotary Selector Switch:
Position Function
0 The JTAG Chain can be accessed via JTAG Header
1 The JTAG Chain can be accessed via JTAG Header [default]
2
Software Controlled:
o Outputting HIGH level at GPIOH7 Pin when Interface A is configured to
MPSSE-Mode enables JTAG over USB.
o Outputting LOW level enables JTAG over JTAG Header
The JTAG Chain can be accessed via USB-Controller if Interface A is configured to
MPSSE-Mode
3
TA900 User Manual Issue 1.0.1 Page 9 of 12
3.2 LED Configuration
The yellow LEDs for Interface A and Interface B in the TA900 Front Panel can be configured to operate in
two different ways by setting DIP Switches:
o Set to Logic, the LEDs indicate the logic level of the corresponding interface pins.
o Set to UART, they indicate UART traffic on the Rx Line and Tx Line of the corresponding interface. [default]
4 Drivers
FTDI provides Virtual COM Port (VCP) drivers which cause the USB device to appear as two additional COM
ports available on the PC. These COM ports can be accessed like standard COM ports by the operating
system. The following operating systems are supported:
x Windows 2000, Windows XP, Windows Server 2003, Windows Vista, Windows Server 2008,
Windows 7, Windows Server 2008 R2 (32-bit and 64-bit)
x Linux (32-bit and 64-bit)
x Mac OS X (32-bit, 64-bit and PPC)
x Windows CE 4.2-5.2 (32-bit, ARM, MIPSII, MIPSIV, SH4)
x Windows CE 6.0 (32-bit, ARM, MIPSII, MIPSIV, SH4)
Additionally, FTDI provides D2XX drivers which allow direct access to the USB device through a DLL. This
offers the user to design application software which can access the USB device through a series of DLL
function calls. The project FTCJTAG DLL can be downloaded at the FTDI homepage to handle all Multi-
Protocol Synchronous Serial Engine (MPSSE) commands necessary to create a USB to JTAG interface. The
following operating systems are supported:
x Windows 2000, Windows XP, Windows Server 2003, Windows Vista, Windows Server 2008,
Windows 7, Windows Server 2008 R2 (32-bit and 64-bit)
x Linux (32-bit and 64-bit)
x Mac OS X (32-bit, 64-bit and PPC)
x Windows CE 4.2-5.2 (32-bit, ARM, MIPSII, MIPSIV, SH4)
x Windows CE 6.0 (32-bit, ARM, MIPSII, MIPSIV, SH4)
TA900 User Manual Issue 1.0.1 Page 10 of 12
5 Pin Assignment – I/O Connector
5.1 Front I/O
The following figure shows the Front I/O Interface of the TA900.
Figure 5-1 : TA900 Front I/O
5.1.1 USB B-type Receptacle
4
Pin-Count
USB B-type Receptacle
Connector Type
Kycon KUSBX-BS1N-W or compatible
Source & Order Info
Table 5-1 : USB B-type Receptacle details
Figure 5-2 : USB B-type Receptacle view
The TA900 comes with a USB A to USB B Cable
(Reichelt AK 672/2-3,0 or compatible)
5.1.1.1 Pin Assignment
Pin Signal Description Driven by
1 VBUS +5V PC
2 D- Data - PC, TA900
3 D+ Data + PC, TA900
4 GND Ground
Table 5-2 : Pin Assignment USB B-type Receptacle
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Tews Technologies Hardware per computer
Tews Technologies
Tews Technologies TAMC020-TM Manuale utente
Tews Technologies
Tews Technologies TCP270 Manuale utente
Tews Technologies
Tews Technologies TDRV003-SW-65 Manuale utente
Tews Technologies
Tews Technologies TPMC463 Manuale utente
Tews Technologies
Tews Technologies TMPE633 Manuale utente
Tews Technologies
Tews Technologies TMPE627 Manuale utente
Tews Technologies
Tews Technologies TPMC321 Manuale utente
Tews Technologies
Tews Technologies TVME201 Manuale utente
Tews Technologies
Tews Technologies TAMC261 Manuale utente
Tews Technologies
Tews Technologies TXMC638 Manuale utente
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
