Texecom Impaq SC-W Manuale utente
Installation Manual
Impaq SC-W
INS876-1
INS876-1 2/15
Content
1.0 Introduction 3 ............................................................................................................................
2.0 Initial configuration & learning on 5 ......................................................................................
2.1 DIP switch configuration 5 ......................................................................................................
2.2 Additional inputs 1&2 6 ..........................................................................................................
2.3 Learning the device to the system 6 ......................................................................................
2.4 Using the device with a roller shutter contact 7 .....................................................................
3.0 Wireless range test 8 ................................................................................................................
4.0 Mounting 8 ..................................................................................................................................
4.1 Device mounting 8 .................................................................................................................
4.2 Magnet positioning 9 ..............................................................................................................
5.0 Setting the shock sensitivity 12 ..............................................................................................
6.0 Specifications 14 ........................................................................................................................
7.0 Legal Information 14 .................................................................................................................
INS876-1 3/15
1.0 Introduction
The Impaq SC-W is a wireless shock sensor with an on board magnetic contact. The
product can also be used with an externally wired magnetic contact and has an
additional facility for use with window shutter movement detectors.
When using Premier Elite Firmware Version 2.10 and above the dedicated
Ricochet learn menu can be accessed via the omit key when in the Engineers
menu. For all other firmware versions please refer to the Premier Elite 8XP-
W/32XP-W Installation Manual.
See the Premier Elite 8XP-W/32XP-W Installation Manual for details of how to
change the device attributes and learning.
Figure 1 shows the key parts of the device that are used for configuration.
Figure 1
INS876-1 4/15
INS876-1 5/15
Icon Item
A Function select DIP switch
B Battery
C Magnet sensor
D Sensitivity selection button
E External input terminal block
2.0 Initial configuration & learning on
2.1 DIP switch configuration
Each switch controls one sensor (shown below). The DIP switches should be
changed after the device is learnt to the system (unless you are only using the
device as a Ricochet wireless repeater).
DIP Switch Controls
M Magnetic contact sensor
S Shock sensor
T1 Terminal 1
T2 Terminal 2
Note 1: Terminal 2 functions as a tamper input. To enable this, configure the DIP
switch labelled T2 to the ON position.
Note 2: To comply with EN50131-2-8, move ONLY DIP switch "S" to the ON
position. To comply with EN50131-2-6, move ONLY DIP switch "M" to the ON
position.
INS876-1 6/15
2.2 Additional inputs 1&2
The Impaq SC-W has 2 additional inputs. These may be used for any normally
closed output device and utilise wireless transmission to the receiver. Typical
examples for use are:
Any locally powered device with a normally closed output e.g. Smoke
detectors, Glass Break detectors, Movement Sensors, Flood detectors etc.
Any non-powered normally closed output device, e.g. Specialist magnetic
contacts, fixed PA buttons etc.
2.3 Learning the device to the system
To learn the device to the system:
Select an empty zone slot for the device and put the system into learn mode.
To power up press and hold the sensitivity button for 3 seconds.
The LED will flash pink while it communicates to the receiver. The LED will
turn green if the device has successfully learnt onto the system. If the LED
turns red the learn has failed.
Check the system is in learn mode.
Move closer to the panel or expander.
Ensure you are learning the device to an “empty” zone.
NOTE: The device will provide a low battery signal to the panel, once this signal is
displayed the battery should be replaced within 30 days.
Configure the DIP switches so that the sensor/s you want to use are set to the
ON position (see example in figure 3).
Figure 3
INS876-1 7/15
2.4 Using the device with a roller shutter contact
The Impaq SC-W can be used with retracting cord contacts to protect door and
window roller shutters. These are particularly useful when the shutter is left in a
partially open position but still needs to be protected against forced entry. The
device is compatible with all microswitch 2 wire roller shutter contacts.
To learn the device with a roller shutter contact:
Connect the roller shutter contact to terminal 1.
Complete the learn process by following the steps in section 2.3.
Configure the DIP switch labelled T1 to the ON position.
To test the device:
Once the device is learnt to the system, pull the cord on the roller shutter
contact.
The device will treat 6 or more pulses within a 10 second period as an
activation.
INS876-1 8/15
3.0 Wireless range test
The wireless range test is available for the first hour after power up or while
the system is in walk test mode – see Premier Elite 8XP-W/32XP-W installation
manual.
With the device in position, press and hold the sensitivity button for 3
seconds.
The LED will flash pink and turn green when a wireless connection is
confirmed.
Should the LED turn red move the device away from metal objects, closer to
the receiver or add more devices to the mesh network.
Once the device leaves commission mode, the device will not show any
status LED’s.
4.0 Mounting
4.1 Device mounting
Select the intended mounting position. The device can be installed in any
mounting orientation.
Open the device cover and remove the PCB using a screwdriver (see figure 4)
To ensure product compliance with EN50131, fix both the detector and
the rear tamper insert to the mounting surface using the following type of
screws:
Head Type: Counter Sunk flat head
Head Diameter: 5.3-6.8mm
Screw Diameter 2.9-3.2mm
Screw length: 15.8-24.5mm
NOTE 1: If the product is mounted on concrete suitable wall plugs should be used.
NOTE 2: If using the magnet, the same screw types should be used for
installation.
Figure 4
INS876-1 9/15
4.2 Magnet positioning
Once the device has been mounted, position the magnet so the notch is
aligned with either of the arrow markers on the sides of the PCB, the LED will
pulse green indicating a secure state.
The magnet can be installed on either side of the device. However, greater
sensitivity is achieved by placing the magnet at the bottom right of the
device and aligning the notch and the arrow. (see figure 5 for magnet
distances)
If the device LED pulses red, move the magnet closer to the device until the
LED turns green.
INS876-1 10/15
The LED indication for magnet positioning is time limited whilst the system is
in commission mode.
Figure 5
Side of
Device Axis Approach Min (mm) Removal Max (mm)
Indice
Altri manuali Texecom Sensore di sicurezza
Texecom
Texecom Prestige DT Manuale utente
Texecom
Texecom Premier Elite AM360 QD Manuale utente
Texecom
Texecom Veritas Reflex Manuale utente
Texecom
Texecom Prestige IR Manuale utente
Texecom
Texecom Premier Elite Impaq Plus-W Manuale utente
Texecom
Texecom Premier External TD Manuale utente
Texecom
Texecom Premier Elite ComWiFi Manuale utente
Texecom
Texecom CAPTURE P15 Manuale utente
Texecom
Texecom Premier Elite CO-W Manuale utente
Texecom
Texecom Premier Elite MR Long Range Manuale utente
Texecom
Texecom Capture A20 Manuale utente
Texecom
Texecom Premier Elite XT-W Manuale utente
Texecom
Texecom Premier Elite DT-W Manuale utente
Texecom
Texecom Premier Elite Impaq Plus-W Manuale utente
Texecom
Texecom Prestige Orbit QD Manuale utente
Texecom
Texecom Capture P15-W Manuale utente
Texecom
Texecom Premier External TD-W Manuale utente
Texecom
Texecom Reflex Manuale utente
Texecom
Texecom CAPTURE D20-W Manuale utente
Texecom
Texecom AED-0009 Manuale utente
