TFA EASY GO Manuale utente

WIRELESS 868 MHz TEMPERATURE STATION

Instruction Manual

INTRODUCTION:

Congratulations on purchasing this compact 868MHz Temperature Station which displays

radio controlled time, date, indoor and outdoor temperature. In addition, the daily minimum

and maximum indoor and outdoor temperature are shown in the normal display. ith only

two keys, this product is ideal for use in the home or office.

EATURES:

The Temperature Station

Foldout

Stand

Battery

compartment

cover

Function

Keys

LCD

Display

Hanging hole

•

Atomic Time function (DCF-77 Radio controlled time) or manual time setting options

•

Atomic Time reception On/Off

•

Hour and minute display

•

Calendar display

•

Time zone option (12 hours

•

ireless transmission at 868 MHz

•

Outdoor signal reception intervals at 4-second

•

Temperature display in degrees Celsius (°C) or Fahrenheit (°F) selectable

•

Indoor and Outdoor temperature display with MIN/MAX recording (records can be

reset)

•

Can receive up to 3 outdoor transmitters

•

Daily minimum and maximum indoor temperature display

•

Daily minimum and maximum outdoor temperature display

•

Low battery indicator

•

LCD contrast adjustable

•

Table standing/ all mounting

The Outdoor Temperature Transmitter

•

Remote transmission of outdoor temperature to

Temperature Station by 868 MHz signals

•

Dual channel transmitter*: one internal channel

and one probe channel

•

Shower proof casing

•

all mounting and table stand

*DUAL CHANNEL TRANSMITTER -

There are an internal channel and an external probe channel in the transmitter.

The data measured by the internal sensor and the measuring probe will be shown on the

transmitter's display as Channel "1" and "2" respectively. The two readings will be

Optional external

probe

This socket is only for the

external probe. Do not apply

power plug to it.

automatically toggled to display. However, if the probe is unplugged, the transmitter' s

display will only show the reading from the inner transmitter.

Once the transmitter is successfully recognized by the temperature station, Channel 1 of

the Temperature station will display the temperature data measured by internal sensor and

Channel 2 will display the temperature estimated by the probe.

If the measuring probe is unplugged, the "probe channel" on Temperature station will show

"---", yet the data from the internal transmitter will still be shown on Channel 1 .

The probe can be connected to the remote temperature transmitter anytime after initial

setup. There is no need to reset the units, should the probe be unplugged or re-plugged

again. The Temperature Station will automatically detect the temperature probe data and

will display the temperature data on Channel 2 after the probe is plugged.

SETTING UP:

When one transmitter is used:

1. First, insert the batteries into the transmitter (see “Install and replace batteries in

the Temperature transmitter” below).

2. ithin 30 seconds of powering up the transmitter, insert the batteries to the

Temperature Station (see “Install and replace batteries in the Temperature

Station” below). Once the batteries are in place, all segments of the LCD will light up

briefly. Then the indoor temperature and the time as 0:00 will be displayed. If they are

not shown on LCD after 60 seconds, remove the batteries and wait for at least 60

seconds before reinserting them. Once the indoor data is displayed, user may

proceed to the next step.

3. After the batteries are inserted, the Temperature Station will start receiving data

signal from the transmitter.

4. If the optional probe has been plugged to the dual channel transmitter, the outdoor

temperature should then be displayed on the Temperature Station on channel 1 and

2. Also, the signal reception icon will be displayed. If this does not happen after 2

minutes, the batteries will need to be removed from both units and reset from step 1.

Note:

Channel 1 will show the reading from the internal sensor of the dual channel transmitter;

Channel 2 will show the reading sensed by the probe. If the probe is not plugged to the

transmitter, " - -" will be shown on Channel 2.

5. In order to ensure sufficient 868 MHz transmission, the final position between the

Temperature Station and the transmitter should not be more than 100 meters (see

notes on “Positioning” and “868 MHz Reception”).

6. Once the remote temperature has been received and displayed on the Temperature

Station, the DCF time code reception is automatically started. This takes typically

between 3-5 minutes in good conditions—but may take up to 4 nights.

When two transmitters are used

1. User shall remove all the batteries from the Temperature Station and transmitters and

wait 60 seconds (if setting has been done with one transmitter before).

2. Insert the batteries into the first transmitter.

3. ithin 30 seconds of powering up the first transmitter, insert the batteries into the

Temperature Station. Once the batteries are in place, all segments of the LCD will

light up briefly. Then the indoor temperature and the time as 0:00 will be displayed. If

they are not shown on the LCD after 60 seconds, remove the batteries and wait for at

least 60 seconds before reinserting them.

4. The outdoor temperature readings from the first transmitter (Channel 1 and 2) should

then be displayed on the Temperature Station (if probe sensor has been installed

onto the first transmitter). If this does not happen after 2 minutes, the batteries will

need to be removed from both units and reset from step 1.

5. Insert the batteries into the second transmitter as soon as the outdoor temperatures

from the first transmitter are displayed on the Temperature Station.

Note: User must insert the batteries into the second transmitter within 30 seconds of

reception of the first transmitter.

6. The outdoor temperature reading from the second transmitter will be shown on the

LCD and the Channel No. will shift back to "1", indicating that all three channels are

running successfully. If this does not happen after 2 minutes, the batteries will need to

be removed from all the units and reset from step 1.

Note: After the Temperature Station has successfully received the second transmitter,

Channel 3 will display the data measured by the internal sensor of the second dual channel

transmitter. Yet the probe data from the second transmitter will not be displayed on the

Temperature Station.

7. Once the remote temperature has been received and displayed on the Temperature

Station, the DCF time code reception is automatically started. This takes typically

between 3-5 minutes in good conditions—but may take up to 4 nights.

IMPORTANT:

•

Transmission problems will arise if the setting for additional transmitters is not

followed as described above. Should transmission problems occur, it is necessary to

remove the batteries from all units and follow the set-up from step 1.

•

If after 10 minutes, the Atomic auto-set time (DCF time) has not been received, press

the SET key to manually enter a time initially.

•

Daily DCF reception is done at 02:00 and 03:00. If the reception at 03:00 is not

successful, then at 04:00 and 05:00 and 06:00 there are other tries, until one is

successful. If the reception at 06:00 is still not successful, then the next try takes

place at 02:00 next day. (Please refer also to notes on “DC -77 Radio Controlled

Time” and “Manual Time Setting”).

BATTERY INSTALLATION

INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE STATION

The Temperature Station uses 2 x AAA, IEC LR3, 1.5V batteries.

To install and replace the batteries, please follow the steps below:

1. Remove the cover at the back of the Temperature Station.

2. Insert batteries observing the correct polarity (see marking).

3. Replace compartment cover.

INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE TRANSMITTER

The temperature transmitter uses 2 x AAA, IEC LR3, 1.5V battery. To install and replace

the batteries, please follow the steps below:

1. Remove the battery compartment cover.

2. Inserte las baterías observando la polaridad correcta.

3. Vuelva a colocar la tapa de la batería en la unidad y

asegúrela re-atornillando nuevamente.

Note:

In the event of changing batteries in any of the units, all units need

to be reset by following the setting up procedures. This is because

a random security code is assigned by the transmitter at start-up

and this code must be received and stored by the Temperature

Station in the first 3 minutes of power being supplied to it

BATTERY CHANGE:

It is recommended to replace the batteries in all units regularly to ensure optimum accuracy

of these units (Battery life see Specifications below).

Please participate in the preservation of the environment. Return used

batteries to an authorized depot.

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Stazione meteorologica popolari di altre marche

Auriol

Auriol AHFL 433 A1 Manuale utente

NexSens

NexSens G2-HYDROMET Manuale utente

Hyundai

Hyundai WS 2202 Manuale utente

IROX

IROX HBVR761 UV-X Manuale utente

La Crosse Technology

La Crosse Technology C86371 Manuale utente

ADE

ADE WS 1711 Manuale utente

Auriol

Auriol z29592 Manuale utente

Auriol

Auriol 296289 Manuale utente

Hyundai

Hyundai WS 2266 Manuale utente

La Crosse Technology

La Crosse Technology WS-2210 Manuale utente

La Crosse Technology

La Crosse Technology WS-811561 Manuale utente

Ventus

Ventus W177 Manuale utente

National Geographic

National Geographic VA Colour RC Manuale utente

Renkforce

Renkforce 1208067 Manuale utente

Levenhuk

Levenhuk Discovery Report WA40 Manuale utente

Instant Transmission

Instant Transmission MA 10410 Manuale utente

Lutron Electronics

Lutron Electronics PHB-318 Manuale utente

WAREMA

WAREMA EWFS Weather station eco Manuale utente