TFT BlitzForce Manuale utente

©Copyright Task Force Tips, Inc. 2006-2018 LIX-730 January 8, 2018 Rev08

MANUAL: BlitzForce

Portable Monitor

INSTRUCTIONS FOR SAFE OPERATION AND MAINTENANCE

DANGER Understand manual before use. Operation of this device without understanding the manual and

receiving proper training is a misuse of this equipment. Obtain safety information at www.tft.

com/serial-number

DANGER Risk of sliding increases at low elevation angles. To reduce risk of injury or death from sliding,

test safety elevation plunger before using.

This Instruction Manual is intended to familiarize ﬁ reﬁ ghters and maintenance personnel with the operation, servicing, and

safety procedures associated with the portable monitor.

This manual should be kept available to all operating and maintenance personnel.

TASK FORCE TIPS, INC.

MADE IN USA • www.tft.com

3701 Innovation Way, Valparaiso, IN 46383-9327 USA

800-348-2686 • 219-462-6161 • Fax 219-464-7155

DANGER

PERSONAL RESPONSIBILITY CODE

The member companies of FEMSA that provide emergency response

equipment and services want responders to know and understand the

following:

1. Fireﬁ ghting and Emergency Response are inherently dangerous activities

requiring proper training in their hazards and the use of extreme caution

at all times.

2. It is your responsibility to read and understand any user’s instructions,

including purpose and limitations, provided with any piece of equipment

you may be called upon to use.

3. It is your responsibility to know that you have been properly trained in

Fireﬁ ghting and /or Emergency Response and in the use, precautions, and

care of any equipment you may be called upon to use.

4. It is your responsibility to be in proper physical condition and to maintain

the personal skill level required to operate any equipment you may be

called upon to use.

5. It is your responsibility to know that your equipment is in operable

condition and has been maintained in accordance with the manufacturer’s

instructions.

6. Failure to follow these guidelines may result in death, burns or other

severe injury.

FEMSA

Fire and Emergency Manufacturers and Service Association

P.O. Box 147, Lynnﬁ eld, MA 01940 • www.FEMSA.org

BlitzForce Portable Monitor BlitzForce OSC Portable Monitor

MAXIMUM OPERATION PRESSURE

175 PSI (12 bar)

MAXIMUM FLOW

500 GPM (2000l/min)

BlitzForce Mounting Bracket

©Copyright Task Force Tips, Inc. 2006-2018 LIX-730 January 8, 2018 Rev08

Table Of Contents

1.0 Meaning of Safety Signal Words

2.0 General Information

2.1 BlitzForce Part Identiﬁcation

2.2 Valve Operation

2.3 Folding Legs

2.3.1 Carbide Spikes

2.4 Full-time Swivel Inlet Coupling

2.5 Outlet Pivots and Safety Elevation Plunger

2.5.1 Elevation Holding Mechanism

3.0 Flows and Pressures

3.1 Automatic, Fixed, and Selectable Flow Nozzles

3.2 Stacked Tips or Smoothbore Nozzles

3.3 Stream Straighteners

3.4 Use with Foam

3.5 Use with Salt Water

3.6 BlitzForce Portable Monitor Pressure Loss

4.0 Deployment of BlitzForce Portable Monitor

4.1 Carrying with an Uncharged Hose

4.2 Carrying with a Charged Hose

4.3 Pressure Gage Port

5.0 Anchoring

5.1 Anchoring by Weight

5.2 Anchoring by Spike Holds

5.3 Anchoring by Hooking Legs

5.4 Anchoring by Tying Off with Safety Strap

6.0 OSC Oscillating Unit

6.1 Safety - Oscillator

6.2 General - Oscillator

6.3 Oscillator

6.4 Oscillating Speed and Coverage

7.0 Storage

8.0 Exploded View and Parts List

8.1 BlitzForce Portable Monitor Exploded View and Parts List

8.2 BlitzForce Oscillator Exploded View

9.0 XXL-B Storage Bracket Installation Instructions

9.1 For Blind Mounting

9.2 For Mounting Where Back Of The Mounting Surface Is Accessible

9.3 Mounting Bracket Dimensions

10.0 Bracket Exploded View and Parts List

11.0 Warranty

12.0 Maintenance

12.1 Service Testing

12.1.1 Hydraulic Testing

12.1.2 Shut-off Valve Test

12.1.3 Records

12.2 Repair

13.0 Answers to Your Questions

14.0 Operation Checklist

©Copyright Task Force Tips, Inc. 2006-2018 LIX-730 January 8, 2018 Rev08

1.0 MEANING OF SAFETY SIGNAL WORDS

A safety related message is identiﬁ ed by a safety alert symbol and a signal word to indicate the level of risk involved with a particular

hazard. Per ANSI standard Z535.6-2011, the deﬁ nitions of the four signal words are as follows:

DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or serious

injury.

WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious

injury.

CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, could result in minor

or moderate injury.

NOTICE NOTICE is used to address practices not related to physical injury.

2.0 GENERAL INFORMATION

The BlitzForce Portable Monitor is an eﬃ cient, compact and easy to maneuver portable monitor. The monitor is a lightweight aluminum

unit, which can deliver 500 GPM of water. This monitor can be mounted in a pre-connected state on the truck-mounting bracket for

achieving quick and eﬀ ective initial attack. General product speciﬁ cations are as follows:

• Standard Inlet Coupling: 2 ½ inch NH Female

• Standard Outlet: 2 ½ inch NH male

• Flow range: up to 500 GPM (2000 LPM)

• Maximum inlet pressure: 175 PSI (12 BAR)

• Vertical Stream Range: 20 to 60° above horizon manned

(30 to 60° above horizon unmanned)

• Horizontal Stream Range: +/- 20 degrees either side of centerline

• Size, legs folded: 14.8”L x 9.0”W x 9.4”H (375 x 230 x 240mm)

• Size, legs unfolded: 15”L x 25.8”W x 10”H (380 x 655 x 254mm)

• Weight: 15 lbs (6.9 kg)

WARNING This equipment is intended for use by trained personnel for ﬁ reﬁ ghting. Its use for other

purposes may involve hazards not addressed by this manual. Seek appropriate guidance and

training to reduce risk of injury.

WARNING An out of control monitor can cause injury or death. To reduce the risk of instability, do not

attempt to move the monitor with water ﬂ owing.

WARNING The ﬂ ow from the monitor may be vital to keep a ﬁ reﬁ ghter from injury or death. Avoid situations

that may interrupt ﬂ ow to the monitor such as: hose line kinks, traﬃ c running over hose, and

automatic doors or devices that can pinch the hose.

CAUTION Master streams are powerful and capable of causing injury and property damage. Make sure

the monitor is pointing in a safe direction before water to the nozzle is turned on. Use care in

directing the stream.

CAUTION Monitor must be properly connected to hose and nozzle. Mismatched or damaged threads may

cause leaking or uncoupling under pressure and could cause injury.

CAUTION Do not couple aluminum to brass. Dissimilar metal coupled together can cause galvanic

corrosion that can result in inability to unscrew threads or complete loss of thread engagement.

CAUTION Use with salt water is permissible provided the monitor is thoroughly cleaned with fresh water

after each use. The service life of the monitor may be shortened due to the eﬀ ects of corrosion

and is not covered under warranty.

©Copyright Task Force Tips, Inc. 2006-2018 LIX-730 January 8, 2018 Rev08

2.1 BlitzForce PART IDENTIFICATION

Figure 2.1 identiﬁ es the various parts and controls of the Portable Monitor.

SEE SECTION 6

FOR BLITZ FORCE

OSCILLATORS

Pivoting Outlet

with Removable

Stream Straightener

Strap Hook

& Anchor

Handle

Locking

Knob

Valve

Handle

Folding

Leg

Carrying

Handle

Knee

Pad

Safety

Elevation

Plunger

Anchor Strap

Reel Assembly

Carbide Tipped Spike

Inlet

Serial

Number

Elevation

Holding

Mechanism

Figure 2.1 Portable Monitor Parts and Controls

2.2 VALVE OPERATION

The valve handle is locked in the closed position so that the

Portable Monitor may be carried/moved without the valve

inadvertently opening when water ﬂ ow is not desired. To unlock

the valve handle from the closed position:

1. Pull knob on right side of valve handle.

2. While pulling on knob move valve handle slowly to an

open position with other hand.

As soon as valve is opened the knob may be released. Valve

handle may be moved to any position by pushing or pulling on

the valve handle. When the valve is closed the valve handle

automatically locks and must be unlocked again to reopen. The

monitor has a label that indicates the direction to open and close

the valve. The valve opening procedure is shown in ﬁ gure 2.2.

Remember to close the valve slowly to reduce water hammer.

2) Open Valve

LOCKED

CLOSED

POSITION

1) Pull Knob

Away

From Handle

To Unlock

Figure 2.2 Valve Opening Procedure

WARNING Injury or death from an out of control monitor can occur. If monitor gets out of control, retreat

from monitor immediately. Do not attempt to regain control of monitor while it is ﬂ owing.

To minimize the risk of an out of control monitor:

• Test Shut-oﬀ Valve before each use.

• Tie oﬀ the monitor when practical.

• Hook legs on stationary objects such as door frames,

cracks, sign posts etc.

• Keep elevation as high as practical.

• Choose surfaces that allow spikes to dig in.

• Assure that the hose is not lifting the spikes oﬀ the ground.

• Reduce ﬂ ow to limit nozzle reaction if stability is questionable.

2.3 FOLDING LEGS

The Portable Monitor has two legs that fold for storage and unfold for operation. The legs are held in the folded and unfolded position

by spring detents. To fold or unfold the legs:

1. Grasp the spike end of one leg and pivot it to the folded or unfolded position.

2. Repeat for the other leg.

WARNING In the unfolded position the legs provide a stable base for operation of the monitor. Lack of

stability can cause an out of control monitor resulting in injury or death. Do not operate as a

portable monitor with either one or both legs in the folded position.

©Copyright Task Force Tips, Inc. 2006-2018 LIX-730 January 8, 2018 Rev08

2.3.1 CARBIDE SPIKES

The BlitzForce Portable Monitor has 3 tungsten carbide tipped spikes on the legs and the base to resist sliding by digging into the

surface the monitor is sitting on. The amount of sliding force these spikes can withstand depends upon the amount of downward and

sideways force that is on the base and the hardness and texture of the surface the spikes are in contact with. At low elevation angles,

it is diﬃ cult for these spikes to resist sliding. These spikes are essential to safe operation of the monitor and must be in contact with

the ground at all times. Set the monitor on an even surface so that all three spikes contact the ground. Replace any spike if the tip

diameter exceeds 1/16 inch (1.6 mm).

WARNING For stable operation the three spikes must maintain in contact with the ground. Do not place

the monitor on top of debris, objects, or uneven terrain that would keep any of the spikes from

contacting the ground.

WARNING On hard slippery surfaces the spikes may provide little resistance to sliding. In these cases the

monitor should be tied oﬀ or the legs hooked on stationary objects to keep the monitor in position.

Also, a person’s weight applied to the monitor may help increase resistance to sliding.

CAUTION Spikes must be sharp to provide resistance to sliding. Replace any spike if the tip diameter

exceeds 1/16 inch (1.6 mm).

CAUTION Spikes are sharp and exposed. Use care around spikes to avoid injury and damage to clothing

or other property.

2.4 FULL TIME SWIVEL INLET HOSE COUPLING

The BlitzForce Portable Monitor has a full-time swiveling inlet coupling so that when the hose is charged, any twist in the hose will

minimize the lifting of the spikes oﬀ the ground. The monitor is equipped with three spikes to provide traction when ﬂ owing from the

ground. For the spikes to provide traction they must remain in contact with the ground. Assure that the hose is not on top of anything

that would cause the spikes to be lifed oﬀ the ground.

2.5 OUTLET PIVOTS AND SAFETY ELEVATION PLUNGER

The monitor’s outlet pivots allow for 20 degrees of horizontal rotation either side of center. The elevation range is from 20 to 60

degrees manned and 30 to 60 degrees unmanned. (30 to 50 degrees with the oscillator version) While manned, to lower the outlet

below the 30 degrees elevation, just push down the outlet to the desired elevation. Below the outlet pivot is a spring-loaded plunger

that returns the outlet to 30 degrees if the operator releases on the outlet or the monitor is unmanned. The pivots are easy to

reposition under pressure and are good for rapid redirecting of the stream. Figure 2.5 shows the outlet pivots range of motion.

Elevation drag adjusting nut.

Tighten to increase drag.

Loosen to decrease drag.

Do not exceed 200 in-lb

(22 N-M) of holding torque.

20°

20° MIN

60° MAX

10° MANNED

30° UNMANNED

Safety

Elevation

Plunger

3X zoom

SIDE VIEW

Figure 2.5 Outlet Pivot Range of Motion

©Copyright Task Force Tips, Inc. 2006-2018 LIX-730 January 8, 2018 Rev08

2.5.1 ELEVATION HOLDING MECHANISM

The elevation pivot has a mechanism to support the weight of a nozzle. It is factory set to support the weight of nozzles likely to be

used. It may be adjusted (see ﬁ gure 2.5). The mechanism releases when raising the nozzle so upwards drag from the mechanism

is not felt. Avoid the use of long stream straighteners or heavy nozzles which may overcome the holding torque of the elevation

mechanism.

3.0 FLOWS AND PRESSURES

The BlitzForce Portable Monitor is designed for maximum ﬂ ows of 500 GPM (2000 LPM) and a maximum pressure of 175 PSI (12

BAR). Do not exceed these limits.

WARNING An inadequate supply of pressure and/or ﬂ ow will cause an ineﬀ ective stream and can result in

injury, death or loss of property.

3.1 AUTOMATIC, FIXED, AND SELECTABLE FLOW NOZZLES

A variety of water or foam nozzles may be used with the BlitzForce Portable Monitor.

Automatic nozzles maintain a constant pressure by adjusting their opening to match the available ﬂ ow. Consult the nozzle manufacturer

for maximum ﬂ ow and pressure ratings. In all cases do not exceed 500 GPM (2000 LPM) and/or 175 PSI (12 BAR).

3.2 STACKED TIPS OR SMOOTHBORE NOZZLES

NOZZLE

DIAMETER

NOZZLE INLET PRESSURE

50 PSI 80 PSI 100 PSI 150 PSI 175 PSI

FLOW

(GPM)

REACTION

(LBS)

FLOW

(GPM)

REACTION

(LBS)

FLOW

(GPM)

REACTION

(LBS)

FLOW

(GPM)

REACTION

(LBS)

FLOW

(GPM)

REACTION

(LBS)

1.0 INCH 210 80 266 126 297 157 364 236 390 275

1-1/4 INCH 328 120 415 196 464 245 ————

1-1/2 INCH 473 177 ————————

NOZZLE

DIAMETER

NOZZLE INLET PRESSURE

4 BAR 6 BAR 8 BAR 10 BAR 12 BAR

FLOW

(L/min)

REACTION

(KG)

FLOW

(L/min)

REACTION

(KG)

FLOW

(L/min)

REACTION

(KG)

FLOW

(L/min)

REACTION

(KG)

FLOW

(L/min)

REACTION

(KG)

25 MM 830 40 1000 60 1200 80 1300 100 1400 120

32 MM 1300 70 1700 100 1900 130 ————

38 MM 1900 90 ————————

FLOW EXCEEDS RATING OF BlitzForce PORTABLE MONITOR

3.3 STREAM STRAIGHTENERS

Stream quality, especially with smooth bore nozzles, is generally improved with the use of a stream straightener. A stream straightener

is integrated into the exit of the monitor.

3.4 USE WITH FOAM

The monitor may be used with various foam nozzles and foam solutions. Refer to ﬁ re service training for the proper use of foam.

3.5 USE WITH SALT WATER

Use with salt water is permissible provided the monitor is thoroughly cleaned with fresh water after each use. The service life of the

monitor may be shortened due to the eﬀ ects of corrosion and is not covered under warranty.

©Copyright Task Force Tips, Inc. 2006-2018 LIX-730 January 8, 2018 Rev08

3.6 OPERATING ENVELOPE AND PRESSURE LOSS

600

Pressure (BAR)

0 100 200 300 400 500

Flow (GPM)

100

150

200

250

300

350

400

Pressure (PSI)

0 500 1000 1500 2000

Maximum Monitor

Inlet Pressure

Flow (L/MIN)

Figure 3.6a BlitzForce Operating Envelope

0.0

5.0

10.0

15.0

20.0

25.0

30.0

35.0

40.0

0 100 200 300 400 500

FLOW (GPM)

LO SS ( PS I)

0.0

0.5

1.0

1.5

2.0

2.5

0 400 800 1200 1600 2000

FLOW (LPM)

LOSS (BAR)

BLITZFORCE PORTABLE MONITOR

8 PSI LOSS AT 500 GPM

OSCILLATING BLITZFORCE

18 PSI LOSS AT 500 GPM

Figure 3.6b BlitzForce Pressure Loss

4.0 DEPLOYMENT OF BlitzForce PORTABLE MONITOR

It is the responsibility of the individual ﬁ re department or agency to determine physical capabilities and suitability for an individual’s

use of this equipment.

4.1 CARRYING WITH AN UNCHARGED HOSE

On a preconnected hoseline the monitor may be carried by the T-shaped handle or over the shoulder with the legs folded as

illustrated in ﬁ gure 4.1.

Figure 4.1 Carrying the BlitzForce on an Uncharged Hose

4.2 CARRYING WITH A CHARGED HOSE

On a charged hose the BlitzForce Portable Monitor may be carried by holding the T-shaped handle located on top of valve body

as shown in ﬁ gure 4.3. Shut-oﬀ valve handle should be locked in the closed position to keep the valve from inadvertently opening.

4.3 PRESSURE GAGE PORT

There is a 1/8” NPT female threaded hole on the back of the inlet

casting. The holes are plugged from the factory. If a pressure

gage is desired, unscrew the plug and install the gage using pipe

sealant. Make sure the gage does not interfere with operation.

5.0 ANCHORING

The nozzle reaction force on the BlitzForce Portable Monitor may be as high as 330 lbs - 500 GPM at 175 PSI (150 kg- 2000 LPM

at 12 BAR). This nozzle reaction must be restrained to keep the monitor from moving.

The monitor should be anchored from moving by one or more of these methods:

METHOD RISK of MOVING

Anchoring by Weight High

Anchoring by Spike Holds Medium

Hooking legs on vertical surfaces Medium

Using a tie oﬀ strap Low

5.1 ANCHORING BY WEIGHT

On surfaces with good traction a person’s weight on the monitor and/or hose may be suﬃ cient to keep the monitor from sliding. This

is highly dependant on the friction of the surface. The ability to keep one or more people’s weight on the monitor is subject to operator

fatigue and may not be as reliable as other methods. Operating at limited ﬂ ows will reduce the risk.

5.2 ANCHORING BY SPIKE HOLDS

The holding ability of the spikes is generally excellent on surfaces like asphalt, wooden and carpeted ﬂ oors because they allow

the spike to penetrate well. On hard smooth surfaces such as ceramic tile, smooth concrete, marble, terrazzo, or steel decking the

BlitzForce Portable Monitor’s spikes may not hold well. Placing the spikes into cracks, expansion joints, or gratings or the like will

help hold the monitor from sliding. Even with the spikes anchored, sliding may be caused by the surface cracking under the load,

or from the hose or nozzle moving the monitor thereby dislodging the spikes from their hold. Figure 5.2 shows a close up of a spike

caught in a crack.

The holding ability of the spikes on soft surfaces such as sand, gravel and mud is generally poor, therefore other anchoring methods

should be considered.

Figure 5.2 Spike Caught in a Crack

5.3 ANCHORING BY HOOKING LEGS

The legs on the BlitzForce Portable Monitor point back slightly so they can act as a hook for anchoring on posts, walls, door frames

or other ﬁ xed objects. Sliding can occur if the legs are unhooked due to the inﬂ uence of the hose, nozzle, or operator. See ﬁ gure 5.3

for illustrations of this.

Good

Nozzle reaction keeps leg hooked.

Object is close to hose.

Poor

Nozzle reaction tends to unhook leg

Good

Nozzle reaction keeps leg hooked.

Hose hits wall and helps hold position.

Poor

Nozzle reaction tends to unhook leg.

Figure 5.3 Hooking Legs to Gain Support

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Attrezzatura di sicurezza popolari di altre marche

Innova

Innova Xtirpa Manuale di istruzioni

bolle SAFETY

bolle SAFETY B810 Manuale utente

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Manuale utente

Hiltron security

Hiltron security POWER8E Guida

Hatco

Hatco B-950P Manuale utente

Sitec

Sitec TX MATIC Manuale utente

TEUFELBERGER

TEUFELBERGER GRIP 12 Manuale utente

MSA

MSA PremAire System Manuale utente

AMC

AMC 1022M Series Manuale utente

Trinity

Trinity CASS S3 Manuale utente

CMC

CMC Helitack HotSeat Manuale utente

Force

Force P-35 Manuale utente

ACM

ACM SAFETY D200 Manuale del prodotto

Honeywell

Honeywell Miller H-Design DuraFlex Manuale dell'operatore

ROCK

ROCK P-451 AS Manuale utente

Power first

Power first 2XYR7A Manuale di servizio

SCHUBERTH

SCHUBERTH SHP 28-C Manuale utente

Trango

Trango CINCH Manuale utente