The QuickLock Padlock Manuale utente
Padlock
RFiD + Bluetooth + Access Control
“On” Button
Shackle
Blue LED
RFiD Read
Target Area
Package Contents:
Padlock
2 –RFiD Key Cards
1 –RFiD FOB
Micro USB Cable
Red LED
Opening the Padlock with RFiD
RFiD –Press the button on the Padlock, and a blue LED will begin to flash.
With the blue LED flashing, place one of the preprogrammed RFiD tags that came with the Padlock up close to
the Q-Logo and the Padlock should open.
Closing the Padlock
The Padlock has a spring loaded latching mechanism. To close the Padlock, simply press down on the shackle.
You should feel the latches engage.
Padlock Initial Set-up
Downloading the App
There is a free App provided for configuration of your Padlock. There is an App for both iOS and Android
phones. To download the App, go to the iTunes Store or the Google Play store, depending on your device, and
search for SafeTech and download the SafeTech App.
When you first open the App, you will need to accept all permissions (if asked), accept the End-User Agreement
and choose a name before you can connect to the Padlock.
App Install and Use
Connecting with Bluetooth
To connect the Padlock to the App, press “Add Device” on the App and then press the button on the Padlock.
The blue LED will begin to flash on the Padlock and then turn solid when the phone connects to the Padlock.
Within 15 seconds, a dialog box will pop up asking for a password. The default password for the Padlock is
12345678. It is recommended that you change the password immediately. (Warning: the password is only
stored on the Padlock and on the App. If the App is removed or replaced, the password will be deleted from
your phone and must be reentered. If you forget your password, the SafeTech support team will not be able to
recover it for you. To recover your password, you will need to send in your Padlock to be reprogrammed. This
service is not covered under warranty). If the App gets stuck verifying the password, refer to the next section
about pairing the SK-1 to your phone.
Pairing the Padlock to a Phone
For many phones the pairing step is completed by the phone automatically. If you are having trouble getting the
App to verify your password the first time you are using the App, it may because the Padlock is not properly
paired to your phone. To pair manual, open the App, press the button on the Padlock and press “Add Device”
on the App. Once the password dialog box pops up, pull down your phones Notification screen by swiping from
the top of the screen down. Look for a pairing request in the notifications. To pair, you will need to select the
notification and then press pair. You should now be able to type in the password and continue to the App
Unlock screen.
Reconnecting with the App
Once you have connected the Padlock to the App, it should connect automatically every time. To reconnect,
open the App to the Home screen, ensure that Bluetooth is on and press the button on the Padlock. The
Padlock will then connect automatically and take you to the Unlock screen. You will not need to press “Add
Device”again or reenter your password.
Unlock Password
There is an additional password option on the App that further secures the Padlock with an additional 4-digit
code. To enable this feature, press the slide below Password Enabled. A dialog box will pop up instructing you to
enter a password. Enter a 4-digit password and press “Save.”The switch under Password Enabled will show
orange, and now after you press “Unlock,”the App will now require that you enter the 4-digit code before the
Padlock opens up. To turn off this feature, press the slide under Password Enabled again and enter the 4-digit
password.
Auto Unlock
The Padlock can be setup to automatically unlock when it connects with the App. To enable automatic
unlocking, press the slide under Auto Unlock. From now on, every time you connect the Padlock to the App, it
will unlock automatically. To turn off this feature, press the slide under Auto Unlock again.
Adjusting Settings through the SafeTech App
There are a number of settings that can be adjusted on the SafeTech App. To access these settings, connect the
Padlock to the App. Once connected, press the settings cog in the bottom right hand corner of the screen and
you will be taken to the Settings screen.
User Name
The User Name is the name the Padlock uses to identify that your phone has opened the Padlock. This is
identified on the History Log, see History Log below. To make a change, press “User Name,”type in a different
name and press “Save.”
Device Name
The Device Name is the name the App uses to identify which device the phone is connected too. To make a
change, press “Device Name,”type in a different name and press “Save.”
History Log
The History Log shows a log of all recent openings of the Padlock using RFID or the App.To access the log, press
“History Log” (Note, names will only be visible for App openings and for RFiD tag names stored on the phone
being used to view the History Log. Openings that are not associated with a name will show up blank in the
middle column).
Auto lock time
You can set the amount of time the Padlock latches stays open after it is unlocked. To do this, press “Auto Lock
Time,” and change the number of seconds.
RFiD Tag Management
RFiD tags can be added to the Padlock using the App. To do this, press “RFID Tag Management”to get to the
RFID Tag Management screen and then press “Add New Tag.” The blue LED on the Padlock will begin to flash
and the App will display the message, “Place a New RFiD Tag on the Lock to Add it.” Within 5 seconds, place an
RFID Tag/Card directly in front of the Q-Logo to record that tag. The blue LED will flash rapidly to indicate that
the card has been recorded to the Padlock. The RFID tag will also appear on the RFID Tag Management screen.
A name can be added next to the Authorized TagID each time an RFiD tag is added. The App will indicate “time
out” on the bottom of the screen if the tag was not read in time. To remove a tag, press the “-“ sign in the
Delete column next to the tag you wish to remove and press “Yes”when the Warning screen comes up on the
App.
Indice
