Thermaltake Pacific Gaming RL240 D5 Manuale utente

Before Installation

Cautions: Make sure there's enough space when you start set up the LCS product

To ensure a clean loop, flush and rinse your radiators

and water blocks with distilled water before using.

Make sure the fittings are screwed securely when

placing them onto the radiator.

Attach the fans to the radiator

Choose the proper way to mount the pump and reservoir

by referring to the manual (suggest vertical palcement) Attach fittings onto the pump and reservoir

Attach the fittings to the inlet and outlet of the

waterblock.

Attach the waterblock onto the motherboard by

referring to the enclosed manual.

Radiators Case Fan

Pump and Reservoir

Water Blocks

Installation Walkthrough (Example: Core V51)

Place the motherboard into the case. Position the radiator. Attach the pump and reservoir into

the chosen locations.

This product is intended for installation only by expert users. Please consult with a qualified technician for installation.

Improper installation may result in damage to your equipment.

1. Please carefully read the manual before beginning the installation process !

2. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant.

3. DO NOT USE any kind of alcohol or alcohol derivatives with this reservoir or the acrylic tube may crack and fail ! Do not clean it using alcohol either !

Pacific Gaming RL240 D5 PETG LCS Kit

Cutting and Attaching the Tubing

Push the end of the tubing over the fitting ;

make sure the tubing is a tight fit. Slide the

cap over the fitting and rotate it clockwise

until the tubing is sealed in place.

Connect the tubing and check all the

fittings are sealed. The loop order:

Water Black > Radiator

Filling the System

Cautions:

1. Before filling the system, please make

sure that each fitting as well as unused

ports are completely sealed.

2. If there is any case of leaking,

immediately turn off the power and

clean the leak

3. If there's any related electronic parts

stained on liquid coolant, make sure to

completely clean and dry the

components. And then make sure they

all work well.

After switching off the power supply,

connect the PSU power cord and

product cables.

Use the refill bottle to fill coolant into the reservoir

Place your PSU outside of the case and attach it to

the pumps 4pin molex connector, turn on the power

of PSU and make the rest of the system fills up.

Thermaltake recommends the following steps to be taken after completing your water loop setup

1. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance

while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.

2. Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.

3. DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately

4. Fill the reservoir to the top as it will prevent air from going into the pump

5. If necessary tilt the system slightly from side to side to bleed the air out of the loop.

6. Place some paper towels under fittings and joining points to test for leaks.

7. Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.

www.thermaltake.com

Connect the tubing and check all the

fittings are sealed. The loop order:

Pump Outlet > Water Block

onnect the tubing and check all the

fittings are sealed. The loop order:

Radiator > Reservoir Inlet

Indice

Altri manuali Thermaltake Hardware per computer

Thermaltake

Thermaltake TOUGHLIQUID Ultra 360 Manuale utente

Thermaltake

Thermaltake Pacific CL360 Plus Manuale utente

Thermaltake

Thermaltake Pacific TOUGH C240 DDC Manuale utente

Thermaltake

Thermaltake Floe Riing RGB 240 Manuale utente

Thermaltake

Thermaltake Water 3.0 Riing RGB 360 Manuale utente

Thermaltake

Thermaltake TH360 ARGB Sync Manuale utente

Thermaltake

Thermaltake Riing Silent 12 Sync Manuale utente

Thermaltake

Thermaltake Divider 370 TG ARGB Manuale utente

Thermaltake

Thermaltake Toughpower 850 B Manuale utente

Thermaltake

Thermaltake Pacific MX1 Plus Manuale utente

Thermaltake

Thermaltake ARMOR A60 Manuale utente

Thermaltake

Thermaltake Water 3.0 240 ARGB Sync Premium Edition... Manuale utente

Thermaltake

Thermaltake TH120 ARGB Sync Manuale utente

Thermaltake

Thermaltake Pacific V-RTX 4080 Plus Manuale utente

Thermaltake

Thermaltake Pacific RL360 Manuale utente

Thermaltake

Thermaltake Floe RC Ultra 360 Manuale utente

Thermaltake

Thermaltake Pacific V-RTX 2070 Super Plus Manuale utente

Thermaltake

Thermaltake Pacific W5 Manuale utente

Thermaltake

Thermaltake Floe RC240 Manuale utente

Thermaltake

Thermaltake Pacific V-RTX 3080/3090 Plus Manuale utente

Thermaltake

Thermaltake Water 3.0 Extreme S Manuale utente

Thermaltake

Thermaltake Level 10 GT Battle Edition VN10008W2N Manuale utente

Thermaltake

Thermaltake Tai-Chi VB5001SNA Manuale utente

Thermaltake

Thermaltake V3 Black Edition VL8000 Series Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente