Thermo Scientific QDC 300 Manuale utente

QuickStart Doc No. 065516-01 Page 1 of 2 January 2013

CHARGE DETECTOR CELL (QDC 300)

Quick Start

(0.4 mm) P/N: 078841

To ensure proper operation of the QDC 300 follow the instructions below. Refer to the ICS 4000 manual and the

QDC 300 manual for detailed operation guidelines.

Do not attempt to disassemble the QDC 300; it may result in irreversible

damage.

ARNING

The QDC 300 should be installed after the Conductivity (CD) background on

the system is ≤2 µS/cm.

1. Hydration and start up of QDC

The QDC 300 is shipped dry and should be hydrated prior to use. This process ensures that the QDC 300

membranes are fully hydrated and ready for operation. Figure 1A shows the top view of the QDC 300 as

shipped with the “ELUENT IN” line plumbed to the “REGEN OUT” port of the QDC 300. Figure 1B shows the

bottom view of the QDC 300 with the ball stud and connector required for installing the QDC 300.

Figure 1A: Top View of the QDC 300 as Shipped

Figure 1B: Bottom view of the QDC 300

NOTE

QuickStart Doc No. 065516-01 Page 2 of 2 January 2013

The hydration steps for the QDC 300 can be performed online on the ICS 4000 system as outlined below.

A. Ensure that all the consumables except QDC 300 are installed on the ICS 4000 system. Equilibrate the system with the

eluent required for the analysis and wait for the CD background to be < 2 µS/cm.

B. Now install the QDC 300 on the system by aligning the ball stud into the correct receptacle on the QD detector location as

shown in Figure 2.

Figure 2: Proper Installation of the QDC 300

QD Cell

C. Disconnect the blue “ELUENT IN” line on the QDC 300 from the QDC 300 “REGEN OUT” port. Connect a small piece of

waste tubing to the “REGEN OUT” port of the QDC 300 to ensure that during hydration there is liquid flowing out of the

waste tubing.

D. Disconnect the suppressor “REGEN INLET” line from the “CELL OUT” port of the conductivity detector.

E. Turn off the suppressor current at this point.

F. Connect the blue “ELUENT IN” line of the QDC 300 to the “CELL OUT” port of the conductivity detector.

G. Let the QDC 300 flush with cell effluent for 5 minutes while sending the flow out of the QDC 300 “REGEN OUT” port to

waste. This ensures that any leachates from the QDC 300 are driven to waste and not into the suppressor regenerant

channel.

H. Ensure that there is liquid coming out from the waste line in Step G from the “REGEN OUT” port of the QDC 300 before

proceeding further.

I. Turn ON the Power to the QDC 300 from the Chromeleon panel and let the QDC 300 equilibration continue for another 20

minutes.

J. After Step I, remove the waste line from the “REGEN OUT” port of the QDC 300 and discard it.

K. Connect the regen line from the suppressor regenerant channel inlet (line coming out of the suppressor “REGEN IN” port) to

the QDC 300 “REGEN OUT” port (as shown in Figure 2).

L. Now turn on the suppressor current from the Chromeleon panel.

M. The QDC 300 is now installed in the IC system following the plumbing schematic shown in Figure 3.

N. Set the compartment temperature to 15°C for the QDC 300 operation. The QDC 300 device is now ready for use.

Indice

Altri manuali Thermo Scientific Sensore di sicurezza

Thermo Scientific

Thermo Scientific Thermo Scientific Dionex SRD-10 Manuale utente

Thermo Scientific

Thermo Scientific Accela UV/Vis Plus Manuale utente

Thermo Scientific

Thermo Scientific Thermo Scientific Vanquish VC-D40 Manuale utente

Thermo Scientific

Thermo Scientific Corona Veo Manuale utente

Thermo Scientific

Thermo Scientific Vanquish VF-D20 Manuale utente

Thermo Scientific

Thermo Scientific Vanquish VH-D20 Manuale utente

Thermo Scientific

Thermo Scientific Dionex UltiMate 3000 Series Manuale utente

Thermo Scientific

Thermo Scientific VC-D60 Manuale utente

Thermo Scientific

Thermo Scientific Dionex UltiMate 3000 Series Manuale utente

Thermo Scientific

Thermo Scientific Accela PDA Manuale utente

Thermo Scientific

Thermo Scientific Surveyor PDA Plus Manuale utente

Thermo Scientific

Thermo Scientific Dionex ICS Series Manuale utente

Thermo Scientific

Thermo Scientific Surveyor UV Plus Manuale utente

Thermo Scientific

Thermo Scientific RadEye SPRD Manuale utente

Thermo Scientific

Thermo Scientific Dionex UltiMate 3000 Series Manuale utente

Thermo Scientific

Thermo Scientific Surveyor RI Plus Manuale utente

Manuali Sensore di sicurezza popolari di altre marche

THORLABS

THORLABS PDA10JT Manuale utente

Waeco

Waeco UV-DETECT Manuale utente

Intermatic

Intermatic IOS-DSIMF Manuale utente

urmet domus

urmet domus 1083 Manuale utente

Siemens

Siemens AZL66 Series Manuale utente

BTI

BTI Profiline Multi Finder Manuale utente

Challenger

Challenger SL01 Manuale utente

DMP Electronics

DMP Electronics 1122INT Manuale utente

Rielta

Rielta Ladoga MK-RK Manuale utente

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuale utente

Bosch

Bosch DS835 Manuale utente

DBI SALA

DBI SALA EZ Stop Manuale dell'operatore

Lamptime

Lamptime ST05C Manuale utente

Ubiquiti

Ubiquiti MFI-MSC Manuale utente

Subsite

Subsite 910R Istruzioni per l'installazione

Satel

Satel OPAL Pro Manuale utente

Aleph

Aleph XC-1XTEU Manuale utente

Pima

Pima LARIS QUAD Manuale utente