ThinkTouch COT190E-AWF02 Manuale utente
COT190E-AWF02 Spec1.0
www.cjtouch.com
- 1 -
DongGuan CJTOUCH Electronic Co., Ltd.
PUBLISHED DATE:2013-03-28
COT190E-AWF02
19" Open-Frame Monitor with 4mm/6mm
SAW Touchscreens
COT190E-AWF02 Spec1.0
www.cjtouch.com
- 2 -
REVISION HISTORY
VERSION
DATE
MODEL
PAGE
DESCRIPTION
AUTHOR
1.0
2013/3/28
COT190E-AWF02
First Issued
李丽群
COT190E-AWF02 Spec1.0
www.cjtouch.com
- 3 -
Safety Instructions
1. Read these safety instructions carefully.
2. Disconnect this equipment from anyAC outlet before cleaning. Use a damp cloth. Do not use
liquid or spray detergents for cleaning.
3. For plug-in equipment, the power outlet socket must be located near the equipment and must
be easily accessible.
4. Keep this equipment away from humidity.
5. Put this equipment on a reliable surface during installation. Dropping it or letting if fall may
cause damage.
6. The openings on the enclosure are for air convection. Protect the equipment from overheating.
DO NOT COVER THE OPENINGS.
7. Make sure the voltage of the power source is correct before connecting the equipment to the
power outlet.
8. Position the power cord so that people cannot step on it . Do not place anything over the
power cord.
9. All cautions and warnings on the equipment should be noted.
10. If the equipment is not used for a long time, disconnect it from the power source to avoid
damage by transient over voltage.
11. Never pour any liquid into an opening. This may cause fire or electrical shock.
12. Never open the equipment. For safety reasons, the equipment should be opened only by
qualified service personnel.
13. If one of the following situations arises, get the equipment checked by service personnel:
A) The power cord or plug is damaged.
B) Liquid has penetrated into the equipment.
C) The equipment has been exposed to moisture.
D) The equipment does not work well, or you cannot get it to work according to the user’s
manula.
E) The equipment has been dropped and damaged.
F) The equipment has obvious signs of breakage.
14. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE THE
STORAGE TEMPERATURE IS BELOW -20℃OR ABOVE 60℃. THIS MAY DAMAGE THE
EQUIPMENT.
COT190E-AWF02 Spec1.0
www.cjtouch.com
- 4 -
1.1 Introduction
Long lasting product cycle-enclosure controlled by CJtouch specifications
Future generation panels phased-in without external changes
High quality panel with high brightness,high contrast ratio and broad viewing angle
Multiple mounting options including VESAmount, horizontal or vertical bracket-mount
Compact and slim profile for easy integration from side,top and bottom
CJtouch’s SAW technology on pure glass for the ultimate in image quality
Finger or gloved hand operation
Dual USB/Serial touch interface port
Worldwide agency approvals
1.2 Product Features
1.2.1 General
Model
COT190E-AWF02
Series
Dust-proof and Compact
Monitor Dimensions
Width: 415mm Height: 343mm Depth: 54.2mm
Weight（N.W/G.W）
6Kg / 8Kg (Approx.)
LCD Type
19”SXGA Color TFT-LCD(HSD190MEN6)
Video Input
VGA & DVI
Recommend Resolution
1280×1024@75Hz
OSD controls
Allow on-screen adjustments of Brightness, Contrast Ratio,
Auto-adjust, Phase, Clock, H/V Location, Languages, Function, Reset
Power Supply
Type: External brick
Input (line) voltage: 100-240 VAC, 50-60 Hz
Output voltage/current: 12 volts at 4 amps max
Mount Interface
1)VESA 75mm and 100mm
2)Mount bracket, horizontal or vertical
Regular Warranty
5 years for SAW Sensor; 3 years for controller; 1 year for LCD
Agency Approval
FCC,CE
1.2.2 LCD Specification
Active Area(mm)
376.320(H)×301.056(V)
Resolution
1280×1024@75Hz
Dot Pitch(mm)
0.294×0.294
Nominal Input Voltage VDD
+5.0V(Typ)
Viewing angle (v/h)
80°/85°
Contrast
1000:1
Luminance(cd/m2)
250
Response Time(Rising/Falling)
3.6s/1.4s
Support Color
16.7M colors
Backlight MTBF(hr)
50000
COT190E-AWF02 Spec1.0
www.cjtouch.com
- 5 -
1.2.3 Touchscreen Specification
Type
Cjtouch SurfaceAcoustic Wave(SAW)
Resolution
4096*4096
Light Transmission
92%
Touch Life Cycle
50 millions
Touch Response time
16ms
Touch System Interface
RS-232 and USB interface
Power consumption
+5V@80mA
1.2.4 External AC Power Adapter
Output
DC 12V /4A
Input
100-240 VAC, 50-60 Hz
MTBF
50000 hr at 25°C
1.2.5 Environment
Operating Temp.
0～50°C
Storage Temp.
-20～60°C
Operating RH:
20%～80%
Storage RH:
10%～90%
1.3 System setup
1.3.1 Preparing for First-time Use
Before you start to set up the LCD Monitor, You should have at least the following items ready in
your accessory box:
A) 12V DC Power adapter;
B) Power cord for adapter;
C) VGA cable;
D) RS-232 cable or USB cable
E) L-brackets：Two standard L-brackets are included
F) CD driver for LCD Monitor
1.3.2 I/O arrangement
The diagram shows the VGAport, RS-232 port, USB port and DC Power inlet
COT190E-AWF02 Spec1.0
www.cjtouch.com
- 6 -
1.3.3 OSD Control
OSD buttons
Adjusting with OSD control
Five different keys are well-defined for operation . They are labeled on the keypad.
A) [Power] Key is designated for Power On/Off
B) [Menu] Key is designated for Menu/Enter function depending on the selected item. Pressing
[Menu] can invoke OSD menu.After that, [Menu] is also an entry key.
C) [+] key is designated for selection function in up direction in OSD menu and also to increase
the value on selected function.
D) [-] key is designated for selection function in down direction in OSD menu and also to
decrease the value on selected function.
E) [AUTO] key is designated for invokingAUTOADJUST function at any time once is pressed for
H-position, V-position, Pixel Clock and Phase for an optimal image.
DVI
VGA
DC
RS232
USB
OSD
COT190E-AWF02 Spec1.0
www.cjtouch.com
- 7 -
1.3.4 Setup the driver
1. Make sure the Touchscreen Cable is properly connected. The Setup program cannot configure the
touchscreen without it.
2. Insert the CD Kit into your PC system’s CD drive.
3. Click the SETUP.EXE installation program. The Setup program begins to execute and load the
CJTOUCH’S driver.
4. Follow the instructions displayed on the screen. Make your selections carefully when ansereing
questions to complete the installation.
1.4 Mechanical Dimension
1.4.1 Touch Monitor Mounting guide
COT190E-AWF02 Spec1.0
www.cjtouch.com
- 8 -
1. Build 8 screw studs along the four sides of the cut out opening based on the dimension given on
the drawing above.
2.Thghten the screw stud with hex nut and make sure it is stable.
1.4.3 Exploded Diagram
1.5 Electrical Block Diagram
The LCD touch monitor is constructed based on steel open frame architecture. It consists of a19”LCD
panel, an DC to AC inverter board to support a set of cold cathode fluorescent light, an analog to digital
converter board (AD Board) to convert analog RGB signals to digital ones, and a touchscreen used as a
pointing device. A metal chassis supports the whole module.
Block Diagram
COT190E-AWF02 Spec1.0
www.cjtouch.com
- 9 -
2.0 Solutions to Common Problems
Problem
Suggestion(s)
The monitor does not respond
after you turn on the system
1)Check that the monitor’s Power Switch is on.
2)Turn off the power and check the monitor’s power cord
and signal cable for proper connection.
Characters on the screen are dim
Refer to the About Touchmonitor Adjustments section to
adjust the brightness.
The screen is blank
1)During operation, the monitor screen may
automatically turn off as a result of the Power Saving
feature. Press any key to see if the screen reappears.
2) Refer to the About Touchmonitor Adjustments section
to adjust the brightness.
Screen flashes when initialized
Turn the monitor off then turn it on again.
“Out of Range” display
Check to see if the resolution of your computer is higher
than that of the LCD display.
Touch doesn’t work
Make sure the touch cable is securely attached at both
ends.
3.0 Typical Application
Gaming/Casino Systems
Outdoor and indoor Kiosks
Entertainment
Transport and Ticketing
Hospitality
Banking
Customizsed Solutions
4.0 How to contact us
www.cjtouch.com
Add
：
Block B, 5th floor,Building 6,
Anjia industrial park, WuLian,
FengGang, DongGuan,P.R.China
Tel
：
+86-769-82522511
Fax
：
+86-769-82522517
Sales & Marketing
：
Indice
Altri manuali ThinkTouch Schermo tattile
Manuali Schermo tattile popolari di altre marche
Elecro Engineering
Elecro Engineering Poolsmart Plus Istruzioni per l'installazione
Johnson Controls
Johnson Controls IQ4 HUB Manuale utente
Elo TouchSystems
Elo TouchSystems ET2270L Manuale utente
Elo TouchSystems
Elo TouchSystems ET1002L Manuale utente
Elo TouchSystems
Elo TouchSystems 3201L Manuale utente
Duratec
Duratec S15 Manuale utente
