Third Millennium OSDP RX Series Manuale utente

P.T.O.www.tm-readers.comSpecifications subject to change without notice.©2018 Third Millennium Systems Limited. All rights reserved.All trademarks are the property of their respective owners.100-02707-CRXThe RX SERIES of OSDP readers provide a powerfully secure and innovative design, offering a clean and stylish aesthetic to any installation.This document provides a general guidance for connecting and fixing the RX SERIES of OSDP readers, and apply to all styles of reader in this series.To fix the reader ensure the top-edge fixing lugs engage correctly with the recesses located at the top of the backplate.

fixing and connection

Pull bottom edge of reader MODULE away from the backplate, and lift up.1Swing the bottom edge of the module down and forward until you feel the unit click shut.5Secure the reader module to the backplate using the M3x10mm screw as supplied.6Mount the reader BACKPLATE to a flat surface using suitable fixings having a diameter no greater than 4mm (0.15 inch).24You may opt to use an M3x10mm countersunk security screw.3When the BACKPLATE has been mounted, make wire connections to the reader MODULE (see over) and your control panel.Ensure you arrange the cable such not to impair or prevent the reader module being properly secured to the backplate.

Mounting this reader on (or near) metal may impair the read range of the unit.reader styles

EU Directive2014/53/ECcompliantRoHSEU Directive2011/65/ECEU Directive2012/19/EUGo to:www.tm-readers.comto view or download datasheetsto our series of readersOSDP readerDEFAULT SETTINGS:BAUD RATE9600for additional BAUD RATE & ADDRESS settingssee:OSDP CONFIGURATION GUIDEforRX SERIES of READERS100-02836

ADDRESS0for additional information see:OC1 INSTALLATION GUIDE100-02776

12109

OC1 OSDPCONVERTEROC1 OSDP converter to be located adjacent to your access control panel in a SECURE area.

existingWIEGANDaccesscontrol panel

LED OPERATION1.No communication withreader - LED flash RED 1/sec.2.Communication with readerNOT using AES secure -LED shows steady YELLOW.3.Communication with readerand IS using AES secure -LED shows steady BLUE.IMPORTANTFit 120 ohms resistor(supplied) to TERMINAL connections#9 and #10 as shown.- 1- 2- 3- 4- 5- 6- 7- 80V+Vdc INDATA1/CLKDATA0/DATAGREENREDBuzzerTMPR 4 -RS-485+ 3 -RS-485- 2 -+Vdc OUT 1 -0V

OC1 OSDPCONVERTERSecureRecommended cable for OSDPBELDEN 9502 (or equiv min 24 AWG).Recommended cableWiegandBELDEN 9538 (or equiv min 24 AWG).

12109IMPORTANTFit 120 ohms resistor(supplied) to TERMINAL connections#9 and #10 as shown.

OSDPaccesscontrol panel

PIN OUT (OSDP reader connection) 1- 0VSupply voltage ground 2-+VdcSupply voltage (+10Vdc to + 16Vdc) 3-not used 4-not used 5-not used 6-not used 7-not used 8-not used 9-RS-485 -RS-485 Bus10 -RS-485 +RS-485 BusSecureRecommended cable for OSDPBELDEN 9502 (or equiv min 24 AWG).Aconnection OSDP reader to OSDP CONTROL PANELBconnection OSDP reader via OC1 to WIEGAND CONTROL PANEL

Indice

Altri manuali Third Millennium Controllori di accesso IP