THORLABS PDAPC3 Manuale utente

PDAPC3

InGaAs Switchable Gain

Photodetector,

OEM Package

User Guide

InGaAs Switchable Gain Detector, OEM 
 
Table of Contents 
Chapter 1 Warning Symbol Definitions ...........................................1 
Chapter 2 Description........................................................................2 
Chapter 3 Setup..................................................................................3 
Chapter 4 Operation...........................................................................8 
4.1. Theory of Operation......................................................8 
4.2. Responsivity .................................................................8 
4.3. Dark Current.................................................................8 
4.4. Bandwidth and Response ..............................................9 
4.5. Terminating Resistance.................................................9 
4.6. Gain Adjustment...........................................................9 
Chapter 5 Troubleshooting.............................................................10 
Chapter 6 Specifications.................................................................11 
6.1. Response Curve...........................................................12 
6.2. Mechanical Drawing ...................................................13 
Chapter 7 Regulatory.......................................................................14 
Chapter 8 Thorlabs Worldwide Contacts.......................................15 

InGaAs Switchable Gain Detector, OEM Chapter 1: Warning Symbol Definitions

Rev A, May 7, 2021 Page 1

Chapter 1 Warning Symbol Definitions

Below is a list of warning symbols you may encounter in this manual or on your

device.

Symbol

Description

Direct Current

Alternating Current

Both Direct and Alternating Current

Earth Ground Terminal

Protective Conductor Terminal

Frame or chassis Terminal

Equipotentiality

On (Supply)

Off (Supply)

In Position of a Bi-Stable Push Control

Out Position of a Bi-Stable Push Control

Caution, Risk of Electric Shock

Caution, Hot Surface

Caution, Risk of Danger

Warning, Laser Radiation

Caution: ESD Sensitive Components

InGaAs Switchable Gain Detector, OEM Chapter 2: Description

Page 2 TTN239792-D02

Chapter 2 Description

The PDAPC3 is an amplified, switchable-gain, Indium Gallium Arsenide (InGaAs)

photodetector in an OEM package with an operating wavelength range of 900 to

1700 nm. A DIP switch allows the user to vary the gain in 10 dB steps. A buffered

output drives 50 Ωload impedances up to 5 V. The output signal is readable from

the MMCX connector. We provide MMCX to BNC cables (Item # CA3339) or

MMCX to SMA cables (Item # CA3439). Users can also access the digital pins of

the gain switch or the output through an on-board header.

ESD Caution

This product is ESD sensitive. Take all appropriate precautions to

discharge personnel and equipment before making any electrical

connections to the unit.

InGaAs Switchable Gain Detector, OEM Chapter 3: Setup

Rev A, May 7, 2021 Page 3

Chapter 3 Setup

1. The pin out table for the on-board header (J2), Figure 1, is shown in the

two tables below:

Figure 1 J2 Header

J2 PIN OUT

Designation

GND

OUTPUT

-V

N.C.

Note:

Pins 1 & 5: ±V refers to the power supply positive/negative voltages.

Pins 7, 8, & 9: A0-A2 refers to the three digital pins for the gain adjustment.

Gain Switch Table

Gain

0 dB

10 dB

20 dB

30 dB

40 dB

50 dB

60 dB

70 dB

Pin 10

Pin 1

InGaAs Switchable Gain Detector, OEM Chapter 3: Setup

Page 4 TTN239792-D02

2. Connect a power supply to pins 1, 3, and 5 of the J2 header. The required

power supply voltages are:

J2 Pin

Voltage

+12 VDC

GND

-12 VDC

Thorlabs offers the LD1255-SUPPLY as one compatible power supply

option. Connection to the board is shown below:

Figure 2 Power Supply Connection

InGaAs Switchable Gain Detector, OEM Chapter 3: Setup

Rev A, May 7, 2021 Page 5

3. Digital gain can be adjusted through the J2 header shown in Figure 1 or

using the on-board DIP switch shown below. Each switch is ‘Off’/0 when

in the up position and ‘On’/1 when in the down position.

Figure 3 Location of the On-Board DIP Switches

The following table describes what each switch does:

Switch Number

Function

Enable

To enable the DIP switch settings, set switch # 1 to ‘On’/1. See the table

on page 3 for the corresponding gain settings.

Note: The default DIP switch settings are all in the ‘Off’/0 position and

customer could only use J2 Header for gain setting purposes. When the

DIP switch is enabled, it would override the seetings of the J2 Header.

On-Board DIP

Switches

InGaAs Switchable Gain Detector, OEM Chapter 3: Setup

Page 6 TTN239792-D02

4. The side adjusted potentiometer is used to adjust the voltage output’s

offset at high gain settings (e.g. 70 dB). This part is factory pre-adjusted

so normally the user does not need to adjust it. However, if the output

offset value has fallen out of spec, for example drift over time or

temperature, then it is possible to adjust it back by turning this

potentiometer. Turning the screw head clockwise decreases the offset

voltage and adjusting the screw head conterclockwise increases it.

Figure 4 Side adjusted potentiometer

5. Attach a 50 Ωcoax cable to the output of the PDAPC3 detector. Thorlabs

offers two suitable cable options, the CA3339 MMCX to BNC cable or the

CA3439 MMCX to SMA cable.

When running cable lengths longer than 12", Thorlabs recommends

terminating the opposite end of the coax with a 50 Ωresistor for optimal

performance. Thorlabs Item # T4119 is suitable for this purpose.

Potentiometer

Adjustment

Screw Head

MMCX

Connector

Indice

Altri manuali THORLABS Sensore di sicurezza

THORLABS

THORLABS PDA30B Manuale utente

THORLABS

THORLABS PDB47 C Series Manuale utente

THORLABS

THORLABS PDA07P2 Manuale utente

THORLABS

THORLABS DET25K2 Manuale utente

THORLABS

THORLABS PDA500 Manuale

THORLABS

THORLABS APD450C Manuale utente

THORLABS

THORLABS PDA8A2 Manuale utente

THORLABS

THORLABS PDA10CS Manuale utente

THORLABS

THORLABS DET01CFC Manuale utente

THORLABS

THORLABS PDP90A Manuale utente

THORLABS

THORLABS PDA10CF Manuale utente

THORLABS

THORLABS PDAPC1 Manuale utente

THORLABS

THORLABS INT-POL-1300 Manuale utente

THORLABS

THORLABS PDA10DT Manuale utente

THORLABS

THORLABS PDA10D Manuale utente

THORLABS

THORLABS DET10D2 Manuale utente

THORLABS

THORLABS APD130 Series Manuale utente

THORLABS

THORLABS PDA05CF2 Manuale utente

THORLABS

THORLABS APD410 Series Manuale utente

THORLABS

THORLABS PDA10PT Manuale utente

THORLABS

THORLABS LSS10 Manuale utente

THORLABS

THORLABS PDA20CS2 Manuale utente

THORLABS

THORLABS PDA10A Manuale utente

THORLABS

THORLABS PDA10D2 Manuale utente

Manuali Sensore di sicurezza popolari di altre marche

Waeco

Waeco UV-DETECT Manuale utente

Intermatic

Intermatic IOS-DSIMF Manuale utente

urmet domus

urmet domus 1083 Manuale utente

Siemens

Siemens AZL66 Series Manuale utente

BTI

BTI Profiline Multi Finder Manuale utente

Challenger

Challenger SL01 Manuale utente

DMP Electronics

DMP Electronics 1122INT Manuale utente

Rielta

Rielta Ladoga MK-RK Manuale utente

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuale utente

Bosch

Bosch DS835 Manuale utente

DBI SALA

DBI SALA EZ Stop Manuale dell'operatore

Lamptime

Lamptime ST05C Manuale utente

Ubiquiti

Ubiquiti MFI-MSC Manuale utente

Subsite

Subsite 910R Istruzioni per l'installazione

Satel

Satel OPAL Pro Manuale utente

Aleph

Aleph XC-1XTEU Manuale utente

Pima

Pima LARIS QUAD Manuale utente

Solinst

Solinst 301 Manuale utente