Thule TB60 Manuale utente
TOP-TRACKS WITH BOLTS
SWEDEN
®
CAR RACK SYSTEMS
PARTS INCLUDED
TOOLS REQUIRED (NOT INCLUDED)
5/16" wrench/
tape measure/
electric drill/
fine tip marker/
safety glasses/
A
B
C
D
E
part/ description/
screw M5 x 40mm/
locking hex nut M5/
self adhesive washer M5/
steel washer M5/
acorn cap/
screw end protector/
7⁄32" drill bit/
1⁄8" drill bit/
3mm hex key/
silicone sealant/
track/glissière
vinyl roof protector/
track end cap/
A
B
C
D
E
F
G
H
I
J
K
L
M
12
12
24
12
12
12
1
1
1
1
2
2
4
part
924-0540-20
938-0500-11
853-5367
951-0520-11
853-5364
853-5373
853-5369-02
853-5369-03
853-0947
853-5374
853-5359-03
853-5360-03-97
853-5361
description part number qty.
A
A B C
D E F
J
K
L
M
G
H
I
B
E
C
D
• Place the tracks on the shell, making sure they are parallel and equal distance
from the front edge of the shell.
1
• Installation of Top-Tracks™ requires drilling the roof and permamently installing parts.
• Only install track on fiberglass shells. Not for use on shells manufactured from any
other material.
• Tools and some mechanical skills are required. If concerned about installation, have
tracks installed by professional installer.
• Not for off road use.
• Do not install if roof has had bodywork.
• Do not install on vehicles with sunroofs.
• Do not install on vehicles with factory racks.
COMPATIBILITY AND
RESTRICTIONS
•Starting at either end of the track, mark the end hole using a fine tip marker, and continue to
mark every other hole on the track.
2
•Remove the tracks
from the roof.
3
•Using the 7⁄32" drill bit supplied, drill
a hole into each of the pilot holes.
•Carefully blow away debris.
5
•Remove backing from the self adhesive washers and apply to the bottom of the track.
Only place washers on holes that line up with the holes drilled in the roof.
6
•Using the 1⁄8" drill bit supplied, drill a
pilot hole in the center of each of the
marks.
4
•Apply silcone into each hole.
7
•With end caps inserted into
track, position track over the
holes and install screws at front
and rear.
8
Wear safety glasses
during installation.
Wear safety glasses
during installation.
•Put self adhesive washers on to remaining screws and install them in to
the remaining holes.
9
•Inside the shell, place the steel washer and locking hex nut onto the screw.
10
ROOF/TOIT
•Tighten all screws using a 5⁄16" wrench and the supplied 3mm hex key.
• Two people are required for proper installation.
11
ROOF/TOIT
To finish the installation there are two options.
•Attach a screw end protector onto
each screw. • Cut off the bolt excess length and
place an acorn cap onto the nut.
12
AB
Note: For mounting TK1 bases (not included), use all hardware (thick washer, thin washer, spacer) included with TK1.
SWEDEN
®
CAR RACK SYSTEMS
Altri manuali Thule Accessori per automobili
Thule
Thule WanderWay 3rd Bike Adapter Manuale utente
Thule
Thule EasyFold XT 2 Manuale utente
Thule
Thule Single Step V10 Manuale utente
Thule
Thule FreeRide 532 Manuale utente
Thule
Thule 121 Guida
Thule
Thule 1443 Manuale utente
Thule
Thule 103 Guida
Thule
Thule 185 Manuale utente
Thule
Thule Kit 1260 Manuale utente
Thule
Thule ProRide Manuale utente
Thule
Thule Backpack 966 Manuale utente
Thule
Thule 102 Guida
Thule
Thule SnowPack 7322 Manuale utente
Thule
Thule 2015 Manuale utente
Thule
Thule 230 Manuale utente
Thule
Thule 5925 Manuale utente
Thule
Thule Rapid System 777 Manuale utente
Thule
Thule Omnistor 9200 Manuale utente
Thule
Thule Rapid Fixpoint XT 3005 Manuale utente
Thule
Thule Kit 1051 Manuale utente
