TIE DOWN 70910 Guida rapida
404-344-0000 • www.tiedown.com
605 Stonehill Drive SW, Atlanta, GA 30336
Do not throw away these instructions!
Read and understand these instructions before
using this device. For any questions, please call
(404) 344-0000.
Instruction #08377
E1834; Rev. 3/29/21
Adjustable Swing Gate
Installation and Use
Part #70910
WARNING: This product can expose you to chemicals including Nickel, which is known to the
State of California to cause cancer. For more information go to: www.P65Warnings.ca.gov
Swing Gate Hinge Assembly
Wheeled Gate End Section
Center Adjustable
Swing Gate Section
Hinge Gate End Section
The Adjustable Swing Gate can be
set up to fit 70” to 85” gate widths.
Page 2 of 4
Adjustable Swing Gate
Installation and Use
Part #70910
INSTALLATION
Step 1
Position the Adjustable Swing Gate
between the desired guardrail opening.
Remove the outer u-bolt, washers, and
nylock nuts.
TIE DOWN Safety Products Division • 800-241-1806 • 404-344-0000 • www.tiedown.com
Step 2
Slide the Adjustable Swing Gate into desired
position. The open end of the swing hinge
should fit flush against the guardrail.
Place the u-bolt through the mounting holes
of the Swing Hinge by placing over the
inside of the guardrail. Secure the u-bolt
with the washers and nylock nuts.
Do not fully tighten the nylock nuts.
U-bolt passes over the inside
guardrail through the hinge.
Secure with washers and nuts
Remove u-bolt, nuts, and washers
Page 3 of 4
Adjustable Swing Gate
Installation and Use
Part #70910
TIE DOWN Safety Products Division • 800-241-1806 • 404-344-0000 • www.tiedown.com
Step 3
Extend the Wheeled Gate Section
until it meets the other guardrail.
The Adjustable Swing Gate can be
adjusted 70” up to 85”.
Step 4
Position and slide the Center Adjustable
Swing Gate Section through the center of
the two guardrail end sections.
Make sure the Adjustable Swing Gate opens
and closes smoothly.
Secure the Center Adjustable Section with 4
self tapping screws, as shown to the right.
Mount the screws using the holes on the
inside of the Center Adjustable Section.
Tighten the nylock nuts on the Swing Gate
Hinge.
Self tapping screws (x4)
Tighten Swing Gate
Hinge with nylock
nuts
Slide outward until the
latch fits around the opposite
guardrail
www.tiedown.com
ISO 9001:2015 Certification
Intellectual property of TIE DOWN Inc.
©2020 TIE DOWN, Inc.
Instruction #08348 (E1834 Rev. 3/29/21)
Safety Products Division
605 Stonehill Drive SW
Atlanta, Georgia 30336
800-241-1806 • 404-344-0000
Page 4 of 4
Step 5
Secure the Swing Gate by lowering the Swing Gate
Latch. Wrap the safety chain around both guardrail
posts and insert the end of the safety chain into the
key hole slot.
Swing Gate Latch
(Shown Open)
Wrap safety chain
around both
guardrails
Adjustable Swing Gate
Installation and Use
Part #70910
IMPORTANT!
Guardrail Outriggers MUST be used at both ends of any
interruption in continuous guardrail sections, or at both ends
of a continuous guardrail section.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali TIE DOWN Attrezzatura di sicurezza
TIE DOWN
TIE DOWN Big Foot 60060US Guida
TIE DOWN
TIE DOWN Juggernaut Manuale utente
TIE DOWN
TIE DOWN 70853 Manuale utente
TIE DOWN
TIE DOWN Parapet Anchor Manuale utente
TIE DOWN
TIE DOWN 70818 Manuale utente
TIE DOWN
TIE DOWN 72874 Manuale utente
TIE DOWN
TIE DOWN PENETRATOR Manuale utente
TIE DOWN
TIE DOWN Hippo Anchor 65219 Manuale utente
TIE DOWN
TIE DOWN 14367 Guida rapida
