TIL TDFM-136B Manuale utente

TDFM-136B

VHF/FM DIGITAL AIRBORNE TRANSCEIVER

OPERATING INSTRUCTIONS

Til Document: 08RE399

Rev. N/C

OCT 2010

Technisonic Industries Limited.

TDFM-136B Operating In truction 08RE399

08RE399 TDFM-136B Operating In truction

Techni onic Indu trie Limited

240 Trader Blvd. E.

Mi i auga, Ontario.

L4Z 1W7

tel: (905) 890-2113

fax: (905) 890-5338

web: www.til.ca

SCOPE of MAN UAL

Thi document provide Operating In truction for TDFM-136B tran ceiver with firmware:

Release 1.0.0 Thi manual does not include tran ceiver in tallation in truction . For in tallation

in truction plea e ee Techni onic document: 08RE398.

FCC COMPL IANC E INFORMAT ION

Thi device complie with Part 15 of the FCC Rule . Operation i ubject to the following two

condition : (1) thi device may not cau e harmful interference and (2) thi device mu t accept any

interference received, including interference that may cau e unde ired operation.

W RNING: For compliance with FCC RF Expo ure Requirement , the mobile tran mitter antenna

in tallation hall comply with the following condition :

1. The tran mitter antenna gain hall not exceed 3 dBi.

2. The tran mitter antenna i required to be located out ide of a vehicle and kept at a

eparation di tance of 1.0 meter or more between the tran mitter antenna of thi device

and per on during operation.

NOTE: Thi equipment ha been te ted and found to comply with the limit for a Cla B digital device,

pur uant to Part 15 of the FCC Rule . The e limit are de igned to provide rea onable protection

again t harmful interference in a re idential in tallation. Thi equipment generate , u e , and can

radiate radio frequency energy and, if not in talled and u ed in accordance with the in truction

manual, may cau e harmful interference to radio communication . However, there i no guarantee

that interference will not occur in a particular in tallation. If thi equipment doe cau e harmful

interference to radio or televi ion reception, which can be determined by turning the equipment off

and on, the u er i encouraged to try to correct the interference by one or more of the following

mea ure :

-Re-orient or relocate the receiving antenna

-Increa e the eparation between the equipment and receiver

-Connect the equipment into an outlet or circuit different from that to which the receiver i

connected.

-Con ult the dealer or an experienced radio/TV technician for help.

W RNING:

Change or modification not expre ly approved by Techni onic Indu trie could void the

u er’ authority to operate the equipment.

WA RRANTY INFORMATION

The Model TDFM-136B, VHF/FM Digital Tran ceiver i under warranty for one year from date of

purcha e. Failed unit cau ed by defective part , or workman hip hould be returned to:

Techni onic Indu trie Limited

240 Trader Blvd. E,

Mi i auga, Ontario.

L4Z 1W7

iii

TDFM-136B Operating In truction 08RE399

Document Rev s on Table for 08RE399

Rev. /

Issue Page Descr pt on Date Change

08RE399 TDFM-136B Operating In truction

Ta ble of C ontents

SECTION1 ......................................................................................................................................1

1.1 Control and Di play..............................................................................................................1

1.1.1 Front Panel Layout and Control ....................................................................................1

1.1.2 Channel Parameter Di play............................................................................................2

1.2 Tran ceiver Ba ic Operation..................................................................................................3

1.2.1 Selecting the Active Channel – Main or Guard...............................................................3

1.2.2 Selecting a Main Channel Memory.................................................................................4

1.3 About Command ..................................................................................................................5

1.3.1 Command Level ............................................................................................................5

1.3.2 Command Type ............................................................................................................6

1.3.3 Command Group ..........................................................................................................6

1.3.4 Command Reference.....................................................................................................6

SECTION 2 .....................................................................................................................................7

2.1 Channel Operating Parameter .............................................................................................7

2.1.1 Memory Parameter .......................................................................................................7

2.2 Editing Channel Operating Parameter .................................................................................7

2.2.1 The Frequency Parameter..............................................................................................9

2.2.2 Operating Mode ..........................................................................................................10

2.2.3 Squelch Mode .............................................................................................................11

2.2.4 ID Call Operation..........................................................................................................15

2.3 Scan and Multi-Mode Operation ..........................................................................................16

2.3.1 Scan Operation............................................................................................................16

2.3.2 Multi-Mode Operation...................................................................................................17

2.4 Controlling U er Acce ......................................................................................................18

2.4.1 Control Acce to Command Level .............................................................................18

2.4.2 Set Command Permi ion ..........................................................................................19

2.4.3 Control Acce to Squelch Mode ................................................................................21

2.4.4 Control Editing of Memorie .........................................................................................21

2.4.5 Control Di play of Frequency Information.....................................................................22

2.5 Encrypted Operation ...........................................................................................................23

2.5.1 Loading Encryption Key ..............................................................................................23

2.5.2 A ign KeyTag to Encryption Key ...............................................................................23

2.5.3 A ign Key by KeyTag to Memory................................................................................24

2.5.4 Enable/Di able Encrypted Operation............................................................................26

SECTION 3 ....................................................................................................................................27

3.1 Operator Level 1 Command ..............................................................................................28

3.1.1 Select the Operating Memory for the Main Channel.....................................................28

3.1.2 Increa e Di play Brightne .........................................................................................28

3.1.3 Edit Channel Operating Mode......................................................................................28

3.1.4 Scroll Backward through Available Memorie .............................................................29

3.1.5 Start/Stop Scan............................................................................................................29

TDFM-136B Operating In truction 08RE399

3.1.6 Scroll Backward through Available Memorie .............................................................30

3.1.7 Edit Channel Operating Frequency...............................................................................30

3.1.8 Decrea e Di play Brightne ........................................................................................31

3.1.9 Edit Channel Squelch Mode.........................................................................................31

3.1.10 Command Level Up....................................................................................................34

3.1.11 Toggle memory: current/home....................................................................................34

3.1.12 Toggle Talk Around.....................................................................................................34

3.1.13 Era e Encryption Key ...............................................................................................34

3.2 Operator Level 2 Command ...............................................................................................34

3.2.1 Create/Edit All Channel Information .............................................................................35

3.2.2 Copy Guard to Main ....................................................................................................36

3.2.3 Lock Keypad ................................................................................................................36

3.2.4 Not U ed...................................................................................................................... 36

3.2.5 Edit Scan Li t & Enable/Di able Scan..........................................................................36

3.2.6 Edit Memory Text De cription.......................................................................................37

3.2.7 Create Shadow Memory...............................................................................................38

3.2.8 Copy Main to Guard ....................................................................................................39

3.2.9 Encryption ON/OFF......................................................................................................39

3.2.10 Command Level Up ...................................................................................................40

3.2.11 Command Level Down................................................................................................40

3.2.12 L2–#. Not U ed..........................................................................................................40

3.3 Operator Level 3 Command ...............................................................................................40

3.3.1 Select Boot Channel.....................................................................................................40

3.3.2 A ign Key by KeyTag..................................................................................................41

3.3.3 Di play Firmware Relea e and Ver ion Information.....................................................42

3.3.4 Di play Firmware Relea e and Ver ion Information.....................................................42

3.3.5 Edit Scan Parameter ...................................................................................................43

3.3.6 Configure PTT Timer....................................................................................................44

3.3.7 Side Tone Audio Level Adju t.......................................................................................45

3.3.8 PC Data Upload/Download ..........................................................................................45

3.3.9 Di play Channel Squelch Parameter ..........................................................................46

3.3.10 Command Level Up ...................................................................................................46

3.3.11 Command Level Down................................................................................................46

3.3.12 L3-# not u ed ............................................................................................................46

3.4 Maintenance Command (Level 4).....................................................................................47

3.4.1 Set Default Record.......................................................................................................47

3.4.2 Set Re tricted Level Acce Mode...............................................................................48

3.4.3 Set Command Permi ion ..........................................................................................48

3.4.4 Set Memory Edit...........................................................................................................49

3.4.5 L4-5. not u ed.............................................................................................................50

3.4.6 L4-6. not u ed.............................................................................................................50

3.4.7 Set Frequency Di play.................................................................................................50

3.4.8 A ign KeyTag to Encryption Key .............................................................................50

3.4.9 Set Squelch Re triction ..............................................................................................52

3.4.10 Command Level Up....................................................................................................53

3.4.11 Command Level Down................................................................................................53

3.4.12 L4-# not u ed.............................................................................................................53

3.5 Supervi or Command (Level 5).........................................................................................54

3.5.1 L5-1 not u ed...............................................................................................................54

3.5.2 L5-2 not u ed...............................................................................................................54

3.5.3 L5-3 not u ed...............................................................................................................54

08RE399 TDFM-136B Operating In truction

3.5.4 Re-Set Databa e to Factory Default ...........................................................................54

3.5.5 L5-5 not u ed...............................................................................................................55

3.5.6 Tran parent Mode........................................................................................................55

3.5.7 Edit Pa word .............................................................................................................55

3.5.8 Run Bootloader............................................................................................................56

3.5.9 Set Unit ID (UID)...........................................................................................................56

3.5.10 L5-0 not u ed.............................................................................................................57

3.5.11 Command Level Down................................................................................................57

3.5.12 L5-# not u ed.............................................................................................................57

SECTION 4 ....................................................................................................................................59

4.1 Appendix A. In talling the Jumper for Re tricted Level Acce ............................................59

4.2 Appendix B. CTCSS Tone and DCS Code Table ................................................................60

4.3 Appendix C. Programming Channel data u ing TDP and a PC............................................61

4.4 Appendix D. 2.5 kHz & 6.25 kHz Valid Frequencie .............................................................63

4.5 Appendix E. Default Table ..................................................................................................64

vii

TDFM-136B Operating In truction 08RE399

Ta ble of F gures

Figure 1-1. The TDFM-136 front panel howing control & di play feature ..................................... 1

Figure 1-2. The TDFM-136 di play – unique parameter highlighted...............................................2

Figure 1-3. The TDFM-136 di play - common channel parameter highlighted................................2

Figure 1-4. The active channel di play and control point ................................................................3

Figure 1-5. Control point for electing an active memory for the MAIN channel..............................4

Figure 1-6. The Screen howing 'Level 3” in the Command Level Di play Po ition..........................5

Figure 2-1. The u er creen to edit the Main frequency....................................................................8

Figure 2-2. The u er creen to edit the Guard frequency.................................................................8

Figure 2-3. The u er creen to edit the Main frequency for receive..................................................9

Figure 2-4. The u er creen to edit the Main frequency for tran mit.................................................9

Figure 2-5. The u er creen to edit the Main Operating Mode........................................................10

Figure 2-6. The creen to edit the Main Squelch Mode for receive.................................................12

Figure 2-7. The noi e quelch edit creen......................................................................................13

Figure 2-8. The creen to edit the Main Squelch Mode for tran mit................................................13

Figure 2-9. The CTCSS Tone quelch edit creen..........................................................................13

Figure 2-10. The DCS Code quelch edit creen...........................................................................14

Figure 2-11. The digital NAC quelch edit creen...........................................................................14

Figure 2-12. The digital TalkGroup quelch edit creen..................................................................15

Figure 2-13. The digital ID Call quelch edit creen........................................................................15

Figure 2-14. The Set Unit ID edit creen.........................................................................................16

Figure 2-15. Identifying Graphic for Primary Channel with Shadow ..............................................18

Figure 2-16. Identifying Graphic for Shadow Channel....................................................................18

Figure 2-17. The creen to enter a pa word for re tricted level acce ........................................19

Figure 2-18. The creen to et the Maintenance pa word............................................................19

Figure 2-19. The Screen to Edit the Level 1 Permi ion ...............................................................20

Figure 2-20. The Screen howing Mode Select re triction for Analog Receive.............................21

Figure 2-21. The creen for Enabling/Di abling edit of a pecific Memory......................................21

Figure 2-22. The error creen on trying to edit a di abled memory.l...............................................22

Figure 2-23. The creen for Enabling/Di abling Frequency Di play for a pecific Memory.............22

Figure 2-24. The creen howing memory with frequency di play di abled...................................22

Figure 2-25. The creen to elect the SLN to a ign the KeyTag to...............................................23

Figure 2-26. The creen to edit the KeyTag....................................................................................24

Figure 2-27. The creen to a ign another KeyTag or exit..............................................................24

Figure 2-28. Select the Main memory to a ign the key to.............................................................25

Figure 2-29. Select the KeyTag to a ign to the memory................................................................25

Figure 2-30. Select decrypt on Any Key or A igned Key...............................................................25

Figure 2-31. The creen to a ign another key or exit....................................................................26

Figure 2-32. The analog memory encryption error creen..............................................................26

Figure 2-33. The error creen for no encryption key a igned........................................................26

Figure 2-34. The Encryption Enabled for Main memory creen......................................................26

Figure 3-1. The U er Screen to Enter a Memory Number...............................................................28

Figure 3-2. The U er Screen to Edit the Operating Mode...............................................................28

Figure 3-3. Trying to tart can on a Channel with Scan di abled..................................................29

Figure 3-4. Start can on a Channel with Scan enabled.................................................................29

Figure 3-5. The U er Screen to Edit the Main frequency................................................................30

Figure 3-6. Editing the Squelch Mode.............................................................................................31

Figure 3-7. Editing the Noi e Squelch Value...................................................................................31

Figure 3-8. Selecting the CTCSS Tone Value.................................................................................32

Figure 3-9. Selecting the DCS Code Value.....................................................................................32

Figure 3-10. Editing the P25 TalkGroup Value................................................................................32

viii

08RE399 TDFM-136B Operating In truction

Figure 3-11. Editing the P25 NAC Value.........................................................................................33

Figure 3-12. Editing the P25 ID Call Value......................................................................................33

Figure 3-13. The Screen to Enter a Scan Li t or Enable/Di able Scan...........................................37

Figure 3-14. The Screen Showing Scan Enabled for thi Memory..................................................37

Figure 3-15. Editing the Text De cription........................................................................................37

Figure 3-16. Entering a Primary Memory for the Shadow Channel.................................................38

Figure 3-17. Entering a Shadow Channel Memory Number...........................................................38

Figure 3-18. Edit the Shadow Memory Parameter - Text................................................................39

Figure 3-19. The Encryption Enabled for Main...............................................................................39

Figure 3-20. Selecting Main Channel Boot Memory.......................................................................40

Figure 3-21. Selecting the Memory to A ign the Key to................................................................41

Figure 3-22. Selecting the KeyTag to A ign to the Memory...........................................................41

Figure 3-23. Selecting the decrypt option: Any Key or A igned Key..............................................41

Figure 3-24. Screen to A ign another key or exit..........................................................................42

Figure 3-25. Selecting Edit mode...................................................................................................42

Figure 3-26. Showing the Code Relea e Information.....................................................................42

Figure 2-27. Select the Scan Revert Mode.....................................................................................43

Figure 2-28. Set the Scan Reply Timer Value.................................................................................43

Figure 3-29. Set the Scan Monitor Timer Value..............................................................................44

Figure 3-30. Set the Scan Delay Timer Value.................................................................................44

Figure 3-31. Set the PTT Timer Value.............................................................................................44

Figure 3-32. Set the Side tone Audio Level....................................................................................45

Figure 3-33. Upload/Download Memory Data to/from the PC.........................................................45

Figure 3-34. Di play of the Receive Squelch Parameter Value .....................................................46

Figure 3-35. Di play of the Tran mit Squelch Parameter Value ....................................................46

Figure 3-36. Select the Acce Mode from a li t.............................................................................48

Figure 3-37. Edit the Level 1 Permi ion ......................................................................................48

Figure 2-38. Edit the Level 2 Permi ion ......................................................................................48

Figure 3-39. Edit the Level 3 Permi ion ......................................................................................48

Figure 3-40. Enable/Di able edit of a pecific Memory...................................................................49

Figure 3-41. The Frequency Di play Enable/Di able creen..........................................................51

Figure 3-42. A memory with frequency di play di abled.................................................................50

Figure 3-43. Step through available key by SLN...........................................................................51

Figure 3-44. The creen to edit the KeyTag....................................................................................51

Figure 3-45. The creen to a ign another KeyTag or exit..............................................................51

Figure 3-46. The Screen to Set Available Squelch Mode for Analog Receive...............................52

Figure 3-47. The Screen to Re trict Editing of the Noi e Squelch Value........................................53

Figure 3-48. The Screen to Re trict Available CTCSS Tone .........................................................53

Figure 3-49. Re trict Available DCS Code ....................................................................................53

Figure 3-50. Era e and Re-Program to Factory Default ................................................................54

Figure 3-51. Tran parent Mode......................................................................................................55

Figure 3-52. Edit Maintenance Pa word.......................................................................................55

Figure 3-53. Edit Supervi or Pa word..........................................................................................56

Figure 3-54. The Bootloader Screen...............................................................................................56

Figure 3-55. Set Unit ID Number ( creen for Main hown).............................................................56

Figure 4-1. The Screw Po ition to remove the Left Hand Side Panel............................................59

Figure 4-2. The Shunt Po ition to Enable Re tricted Level Acce ................................................59

Figure 4-3. The Communicate with PC Command Screen.............................................................61

Figure 4-4. The TDP-136 Radio Programming Software Window...................................................61

TDFM-136B Operating In truction 08RE399

Tab le o f Tab les

Table 2-1. Tran ceiver Operating Mode ........................................................................................10

Table 2-2. Receive and Tran mit Squelch Mode ...........................................................................11

Table 2-3. Permi ion Applicability by Command and Level...........................................................20

Table 2-4. Squelch Mode Re triction ............................................................................................21

Table 3-1. Command Level Reference...........................................................................................27

Table 3-2. Tran ceiver Operating Mode ........................................................................................29

Table 3-3. Receive and Tran mit Squelch Mode ...........................................................................31

Table 3-4. Extra Character for Text Edit........................................................................................38

Table 3-5. The Channel Template Factory Default ........................................................................47

Table 3-6. Permi ion Applicability wrt Command Level ...............................................................49

Table 3-7. Squelch Mode that can be Re tricted...........................................................................51

Table 4-1. CTCSS Tone ................................................................................................................60

Table 4-2. DCS Code ....................................................................................................................60

Table 4-3. Valid Frequency Pattern.................................................................................................63

Table 4-4. Memory Template Factory Default ................................................................................64

Table 4-5. Configuration Parameter Default Value ........................................................................64

Table 4-6. Scan Parameter Default Value .....................................................................................64

Table 4-7. Unit Identification (UID) Default Value ..........................................................................64

Table 4-8. Re tricted Level Pa word Default Value .....................................................................64

Altri manuali per TDFM-136B

Indice

Altri manuali TIL Ricetrasmettitore

TIL

TIL TiL-91-DE Manuale utente

TIL

TIL TDFM-136 Manuale

TIL

TIL TDFM-7000 Manuale utente

TIL

TIL TDFM-7300-3 Manuale utente

TIL

TIL TiL-91-DE Manuale utente

TIL

TIL TDFM-9000 Manuale utente

TIL

TIL TDFM-9200 Manuale utente

TIL

TIL TDFM-9300 Manuale utente

TIL

TIL TDFM-136 Manuale

TIL

TIL TDFM-136 Manuale

TIL

TIL TAF-550 Manuale utente

TIL

TIL TDFM-9000 Manuale utente

TIL

TIL TDFM-7300-2 Manuale utente

TIL

TIL TDFM-9100 Manuale utente

TIL

TIL TDFM-136B Manuale utente

TIL

TIL -92-SC TSC-4100 Manuale utente

TIL

TIL TDFM-136B Manuale utente

TIL

TIL TDFM-7300 Manuale utente

Manuali Ricetrasmettitore popolari di altre marche

Yaesu

Yaesu FT-7B Manuale utente

Kenwood

Kenwood ProTalk TK-3201 Manuale utente

Texas Instruments

Texas Instruments TLK10232 Manuale utente

Mizuho

Mizuho MX-2 Guida del prodotto

Kenwood

Kenwood TK-3180 Manuale operativo e di manutenzione

Blitz

Blitz MJ-398U Manuale utente

Utilicom

Utilicom LongRanger 2050 Manuale utente

Standart

Standart HX290UKA Manuale utente

Altronix

Altronix Pace1PTM Manuale utente

Kirisun

Kirisun PT2208 Manuale utente

ELECRAFT

ELECRAFT KX2 Manuale utente

Zodiac

Zodiac K3 Manuale utente

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuale utente

Kenwood

Kenwood TK-2217 Manuale utente

Siemens

Siemens PSO 4000 Manuale utente

Kenwood

Kenwood TS-590SG Manuale utente

Midland

Midland G8E-BT Manuale

ComNav

ComNav Mariner X2 Manuale utente