Time Warner Cable Digital Adapter Guida rapida
Your Digital Adapter
Easy Setup Guide
Connect with the
future of TV
You’re about to step up to a world of
even better picture and sound, and this
Easy Setup Guide is here to help every
step of the way. Just follow the simple
installation instructions on the next
few pages, activate your Digital Adapter,
and you’ll be all set.
Contents
Installation
and Activation
38
Using your new
remote control
910
Troubleshooting
and FAQs
1112
Included in this kit
TWO AAA
BAT TERIES
ADHESIVE
FASTENERS
COAX
CABLE
HDMI
CABLE
POWER
CORD
REMOTE
CONTROL
IR RECEIVER
DIGITAL ADAPTER
Connect the Adapter
to your cable outlet
Turn o your TV.
Locate the cable that runs from
the cable outlet to your TV.
Leave the cable connected to the
wall, but disconnect from your TV.
Reconnect this cable to the
“Cable In” input on the back of
the Adapter.
Connect the Adapter
to your TV
If your TV is Standard Deinition.
Connect the coax cable from this kit
to the “To TV” output on the Adapter.
Connect the other end of this
cable to the “Cable
In”
input on
your TV.
If your TV has an HDMI port.
Connect the HDMI cable from this kit
to the “HDMI” output on the Adapter.
Connect the other end of the
cable to the “HDMI” input on
your TV.
Choose the output channel
If your TV is Standard Deinition.
Set the CH 3/4 Output Switch on the
Adapter to Channel 3 (some parts
of the country use Channel 4).
If your TV has an HDMI port.
Set TV to choose HDMI as
input source.
Connect the power cord
Connect the power cord from this
kit into the “+5V DC In” input on
the Adapter. Plug the other end
into an electrical outlet.
NOTE: Make sure you don’t plug
your power cord into the IR
Receiver input.
The green light on the front of the
Adapter should now be on and
blinking. If it isn’t, make sure the
power cord is properly connected.
If a picture appears, you’re already
activated and can turn to page 9 to
learn how to program your remote.
If no picture appears, then turn to
page 8 to activate.
3| QUESTIONS? twc.com/digitaladapter ^18552861736
Connect to your T V
If you run your cable line through a VCR/DVD, turn to page 5.
A
B
C
D
TELEVISION
DIGITAL ADAPTER
IN TO TV +5V DC INCH 3/4 HDMI
ELECTRICAL OUTLET
CABLE OUTLET
INSTALLATION INSTRUCTIONS | 4
If the Adapter is in a spot where the remote control signal gets blocked, use the included IR Receiver. Plug the IR
Receiver into the “IR In” port on the Adapter, and place the other end where it can be seen in front of the TV using
the adhesive fasteners. Make sure the adhesive fasteners don’t cover your TV vents to avoid overheating.
NOTE: OPTIONAL
IR RECEIVER
Installation Diagram
A
C
B
D
STANDARD CONNECTION HDMI CONNECTION
5| QUESTIONS? twc.com/digitaladapter ^18552861736
Connect the Adapter
to your cable outlet
Turn o your TV.
Locate the cable that runs from
the cable outlet to your VCR/DVD.
Leave the cable connected to the
wall, but disconnect from your TV.
Reconnect this cable to the
“Cable In” input on the back of
the Adapter.
Connect the Adapter
to your VCR/DVD
If your TV is Standard Deinition.
Connect the coax cable from this kit
to the “To TV” output on the Adapter
.
Connect the other end of the
cable to the “Cable
In”
input on
your VCR/DVD.
If your TV has an HDMI port.
Connect the HDMI cable from this kit
to the “HDMI” output on the Adapter.
Connect the other end of the
cable to the “HDMI” input on
your DVD.
Choose the output channel
If your TV is Standard Deinition.
Set the CH 3/4 Output Switch on
the Adapter to Channel 3 (some
parts of t
he country use Channel
4). Make sure this matches the
input channel you’ve selected
for your VCR/DVD.
If your TV has an HDMI port.
Set TV to choose HDMI as
input source.
Connect the power cord
Connect the power cord from this
kit into the “+5V DC In” input on
the Adapter. Plug the other end
into an electrical outlet.
NOTE: Make sure you don’t plug
your power cord into the IR
Receiver input.
The green light on the front of the
Adapter should now be on and
blinking. If it isn’t, make sure the
power cord is properly connected.
If a picture appears, you’re already
activated and can turn to page 9 to
learn how to program your remote.
If no picture appears, then turn to
page 8 to activate.
Connect to your T V+V CR /DVD
If you connect your cable line directly to your TV, turn to page 3.
A
B
C
D
TELEVISION
DIGITAL ADAPTER
VCR/DVD
CABLE OUTLET
INSTALLATION INSTRUCTIONS | 6
IN TO TV +5V DC INCH 3/4 HDMI
Installation Diagram
A
B
C
D
ELECTRICAL OUTLET
B
If the Adapter is in a spot where the remote control signal gets blocked, use the included IR Receiver. Plug the IR
Receiver into the “IR In” port on the Adapter, and place the other end where it can be seen in front of the TV using
the adhesive fasteners. Make sure the adhesive fasteners don’t cover your TV vents to avoid overheating.
NOTE: OPTIONAL
IR RECEIVER
STANDARD CONNECTION HDMI CONNECTION
7| QUESTIONS? twc.com/digitaladapter ^18552861736
Activation
Once you’ve installed all your Adapters you’re ready to activate them.
See the easy to follow instructions to the right. Once activation is
complete, you’ll be ready to program your remote control and get
back to all your favorite shows.
ACTIVATION | 8
Activating your Adapter
Using your TV remote, tune to the HDMI or output
channel you chose during installation (Ch. 3 or 4).
You’ll see an activation screen with our contact number.
Call this number to activate your Adapter.
18552861736
Activation is usually complete in 510 minutes, but could
take up to 20 during peak times. Once complete, the
picture will automatically turn on. If it doesn’t, turn to
the Troubleshooting section on page 11.
The last step is programming your new remote control,
which you can learn how to do on the next page.
9| QUESTIONS? twc.com/digitaladapter ^18552861736
Using your new remote control
Program your remote control
Turn on your TV and tune it to the output channel you
chose during installation (Ch. 3 or 4), or to the proper
HDMI input.
Install the batteries that were included in this
kit in the remote. Press and hold the TV POWER
and PROG buttons until the LED light on the remote
turns on, then release the buttons.
Press the TV POWER button to enter automatic search
mode. Your remote will search for the correct code.
When your TV turns o, press the PROG button within
1 second to store your TV’s code.
Your remote is now programmed and the device code
will be permanently saved.
NOTE: If you have any questions, please refer to the Programming
Guide that came with your remote.
A
B
C
Indice
