Timeguard TRT034N Manuale utente

Installation & Operating Instructions

7 Day Digital Programmer

1 Channel – Surface Mount

Model: TRT034N

1. General Information

These instructions should be read carefully and retained for further reference

and maintenance.

2. Safety

• Before installation or maintenance, ensure the mains supply to the

Programmer is switched off and the circuit supply fuses are removed

or the circuit breaker turned off.

• It is recommended that a qualiﬁed electrician is consulted or used for the

installation of this Programmer and install in accordance with the current

IEE wiring and Building Regulations.

• Check that the total load on the circuit including when this Programmer is

ﬁtted does not exceed the rating of the circuit cable, fuse or circuit breaker.

• To clean use a clean dry cloth only. Do not use any liquid cleaners.

3. Technical Specifications

• 230V AC 50 Hz

• This thermostat is of Class ll Construction and must not be earthed

• Switch Rating: 3(1)A

•Switch Type: Single pole, double throw (SPDT)

change over contacts

•Connection Type: 3 wire

•Installation Type: Surface mount with wall plate

• Micro Disconnection: Type 1.B control action

•Operating Temperature Range: 0°C to +40°C

• Programme: 5 day plus 2, or 7 day set by DIP switches

• Time Control Periods: 3 per day with copy function

• Clock Format: 12 hour AM/PM or 24 hour

• Summer/Winter Changeover: Day light saving, GMT or BST

• Holiday Mode: 0 to 31 day Programme suspension

• Boost Function: 1, 2 or 3 hour

• Battery Backup: 7 Day, factory ﬁtted rechargeable

(non-replaceable)

• Illumination: Blue LED illuminated on setting

for button surrounds and display

• CE Compliant

• Dimensions (H x W x D): 90 x 135 x 30mm

TRT034N Front View

The heating symbol will show

when heat is demanded

12hr am/pm

or 24hr clock

timer display

(illuminated

on setting)

Advance to next Programme,

ON/OFF override and copy function

Up down selection

buttons

1, 2 and 3 hour boost

function (illuminates

on setting)

Display light/Holiday

mode setting button

Flip down cover

conceals setting

buttons

4. Siting

• The TRT034N should be located at a position which eases wiring runs

and gives good access for Programming.

• It should be mounted approximately 1.5m above floor level.

5. Installation

5.1 Ensure the mains supply is switched off and the circuit supply fuses

are removed or the circuit breaker turned off.

5.2 Remove the wall plate from the unit, by undoing the retaining screws,

and pivoting the bottom of the unit outwards. The TRT034N body can

then be lifted off.

5.3 Mark the position of the mounting holes on the wall using the wall plate

as a template. Drill out the mounting holes taking care to avoid any

joists, electrical cables or water/gas pipes that may be hidden beneath

the surface. Insert the rawl plugs into the holes.

5.4 Pass the 230V 50Hz mains supply and load cables through the opening

of the wall plate. Allow sufficient excess cable to wire up the unit, but

not too much to make it difficult to close the unit to the wall plate.

5.5 Fix the wall plate to the wall using the correct mounting screws for the

rawl plugs installed. The retaining screws which secure the unit to the

wall plate should be at the bottom.

5.6 Terminate the cables into the terminal block ensuring correct polarity

is observed and that all bare conductors are sleeved (See section 6.

Connection Diagram). Make sure that the curved washer grips

the conductor.

5.7 To reinstall the unit onto the wall plate, first ensure the wall plate

retaining screws are loosened enough to clear the TRT034N body,

then engage the top of the TRT034N onto the wall plate retaining tabs,

and push firmly downwards and then upwards. There will be some

resistance from the terminals.

5.8 Once in place, secure with the retaining screws making sure

not to over tighten.

TRT034N Wall Plate

Alternate mounting holes

Wall plate retaining screws

Retaining tabs

Mounting

holes

Loop terminal

NC NO

BOILER

230V AC 50Hz

MAINS SUPPLY Supply

Neutral

Supply

Live

Switch Live from NO

(normally open contact

for heating) to Boiler

6. Connection Diagram

Connect the 230V 50Hz mains supply and load cables to the terminal block

which are marked as follows;

• Note: Check boiler instructions before connecting.

230V 50Hz Mains Supply

Live Supply (Brown or Red) to L

Neutral Supply (Blue or Black) to N

A ‘Loop Terminal’ is provided should a 3 core cable

be used

Load (Boiler)

Switch Live (Brown or Red) to NO

DIP switch position label

DIP switches for 5-2

or 7 day Programming

7. DIP Switch Settings

• Decide whether weekday/weekend (5-2) or individual (7) day programming

is required, and set the DIP switches in the correct position on the rear of

the unit. A reset will be required after changing the DIP switch positions.

TRT034N Rear of Unit

8. Reset from Power-up

• Restore mains to the unit after making sure to check all system wiring

is complete, and after you have selected the desired DIP switch settings.

• Press the reset button located beneath the flip down cover on the front

of the unit, all of the characters will briefly appear on the display,

followed by the 12hr clock format screen.

• After 1 minute the screen will time out showing a default time

of 12:00AM.

• There are 3 timed controlled periods per day, and the default

Programmes are as follows;

Heating (HTG)

06:00AM ON

08:00AM OFF

10:00AM ON

12:00PM OFF

06:00PM ON

10:00PM OFF

9. Setting the Time and Date

9.1 To alter the time and date at any time, press and hold the Select button

for 3 seconds, the display light will illuminate.

9.2 The default clock format is 12Hr which will be displayed on the screen.

9.3 Use the Up/Down arrow buttons to either select 24Hr format, or leave

it at 12Hr format, and then press the Select button once to confirm.

9.4 The hour will to flash, use the Up/Down arrow buttons to alter the hour

and press the Select button once to confirm.

9.5 The minutes will flash, use the Up/Down arrow buttons to alter the

minutes and press the Select button once to confirm.

9.6 The year will flash, use the Up/Down arrow buttons to alter the year

and press the Select button once to confirm.

12Hr AM/PM format Use the Up/Down arrow

buttons to change

the time format

24Hr format Use the Select

button to

confirm

Use the Up/Down

arrow buttons to

change the hour

The hour will flash Example of

12Hr AM/

PM format

Use the Select

button to

confirm

Use the Up/Down

arrow buttons to

change the minutes

The minutes will flash Use the Select

button to

confirm

Use the Up/Down

arrow buttons to

change the year

The year will flash Use the Select

button to

confirm

9.7 The month will flash, use the Up/Down arrow buttons to alter the year

and press the Select button once to confirm.

9.8 The day will flash, use the Up/Down arrow buttons to alter the day

and press the Select button once to confirm.

9.9 The daylight saving option (GMT=OFF/BST=ON) will flash, by default this will

be set to OFF. Use the Up/Down arrow buttons to alter the setting. Press the

Select button once to confirm and return to re-enter the date and time from

the beginning, or press the Set button once to confirm and exit.

Use the Up/Down

arrow buttons to

change the month

The month will flash Use the Select

button to

confirm

Use the Up/Down

arrow buttons to

change the day

The day will flash Use the Select

button to

confirm

The DLS will flash,

OFF for GMT by

default

The DLS set to

ON for BST

Use Set to

confirm

and exit

Use Select to confirm

and return to re-enter

time & date

Main screen

showing day,

time and

output status

Note:

• If no button is pressed, it will time out after 60 seconds and return to the

mains screen showing day, time and output status.

• The display light will also time out after 15 seconds after the last button

is pressed.

• The Set button can be pressed to exit the date and time entry at any stage.

Indice

Altri manuali Timeguard Termostato

Timeguard

Timeguard TRT037 Guida del prodotto

Timeguard

Timeguard MLTP180BK Manuale

Timeguard

Timeguard TRT035N Manuale utente

Timeguard

Timeguard TRT044 Guida del prodotto

Timeguard

Timeguard ProgramaStat Guida del prodotto

Timeguard

Timeguard TRT036N Manuale

Timeguard

Timeguard TRT030DN Manuale utente

Timeguard

Timeguard TRT031 Guida del prodotto

Timeguard

Timeguard TRT034 Guida del prodotto

Timeguard

Timeguard ProgramaStat TRT037 Guida del prodotto

Timeguard

Timeguard TRT035 Guida del prodotto

Timeguard

Timeguard TRT033N Manuale utente

Timeguard

Timeguard TRT031N Manuale utente

Timeguard

Timeguard TRT030N Manuale utente

Timeguard

Timeguard TRT032N Manuale utente

Timeguard

Timeguard TRT037N Manuale

Timeguard

Timeguard TRT047N Manuale

Timeguard

Timeguard TRTD7 Manuale utente

Timeguard

Timeguard TRTWIFI Manuale

Timeguard

Timeguard TRT044 Manuale

Timeguard

Timeguard TRT05 Manuale

Timeguard

Timeguard TPT44 Manuale utente

Timeguard

Timeguard TRT05 Manuale

Manuali Termostato popolari di altre marche

EWELLY

EWELLY EW-181 Manuale utente

Prolon

Prolon T1100 Istruzioni per l'installazione

Computherm

Computherm Q20 Manuale utente

Heatmiser

Heatmiser neoStat Manuale utente

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuale utente

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuale utente

Saswell

Saswell SAS920XWHB-7-S-RF Guida

Aircalo

Aircalo TFP1-ET85P2 Manuale utente

Honeywell

Honeywell CM721 Manuale utente

Carrier

Carrier DEBONAIR 33CS Manuale utente

Lennox

Lennox iHarmony Zone Thermostat Istruzioni per il montaggio

Gemtech

Gemtech GT7000 Manuale di istruzioni

Rollei

Rollei Smartes 45000 Manuale utente

Sinope

Sinope TH1300RF Manuale utente

Honeywell

Honeywell RLV4305 Manuale utente

Honeywell

Honeywell Prestige 2.0 THX9421 Manuale utente

NuTone

NuTone NTBZ48 Istruzioni operative originali

Stelpro

Stelpro MAESTRO ASMT402AD Manuale utente