TimeLine Micro Lynx System Unit Manuale utente

ECC 294 Page 173J008 REV A

PROM Installation Guide

Micro Lynx System Unit (SU)

qOptional TIMELINE VISTA, INC.

1755 LA COSTA MEADOWS DRIVE, SUITE B

qRecommended SAN MARCOS, CA 92069

TEL. 760-761-4440

q3Mandatory (FAX 760-761-4449)

[email protected]

System Unit PROM Installation

DATE: 06/12/92

MODEL: Micro Lynx

REVISION: All

SERIAL NO: All

SOFTWARE: Machine Control PROM U51

U47

Control PROM U4

DESCRIPTION:

There are three PROMs in the System Unit. A software upgrade may require replacement of either the

machine or control PROMs. Replace only the PROMs that were shipped to you.

Look at the PROM(s) in the shipping container. The Software Version number is listed on the PROM

label; the number is preceded by MC or CP. Micro Lynx uses two MC (Machine Control) and one CP

(Control Processor) PROM. Both MC PROMs must be replaced at the same time, do not replace only one!

Record the serial numbers and software version in the front of your Micro Lynx Manual, they are

required to receive assistance from Customer Service.

REQUIRED TOOLS:

Static safe workstation Grounding wrist strap

IC Extractor/Insertor Phillips screwdriver

or small screwdriver

PROCEDURE:

1. Turn off the power and disconnect all

power cables.

2. Place the Micro Lynx System Unit on a

static safe workstation. Ground yourself and the workstation anti-static mat.

3. Remove the six phillips screws securing

the top cover to the chassis. Turn the

System Unit so that the front panel faces you and remove the top cover.

ECC 294 Page 273J008 REV A

Figure 1. Open the Top Cover

PROM Installation Guide

4. Locate and replace the appropriate PROMs. Remember to align pin 1 on the PROM with pin 1 in

the socket. All PROMs have a small cutout at one end which indicates the location of pin 1. The

printed circuit board also has a cutout mark at one end of each IC to indicate orientation.

MC U51 and U47

CP U4

Warning

Use an IC inserter to remove and replace the PROMs. If one is not available, use the small flat blade

screwdriver. Insert the screwdriver precisely as shown in Detail B below; twist slightly and gently lift

up the PROM. Inserting the screwdriver incorrectly will damage surrounding components and affect

operation of the Micro Lynx.

May-10 Page 373J008 REV A

Figure 2. System Unit PROM Locations

5. Replace the cover on the System Unit. Insert and tighten the 6 phillips screws. Reconnect the cables and

turn on the power. The System Unit will sense the new software and boot correctly. To verify that the

upgraded software is operating, pressSYS on the Keyboard Unit, the new software version numbers

will be displayed.

Indice

Altri manuali TimeLine Apparecchiature di registrazione

TimeLine

TimeLine Micro Lynx VSG Option Card Manuale utente

TimeLine

TimeLine Micro Lynx ACG Option Card Manuale utente

TimeLine

TimeLine Micro Lynx VITC Option Card Manuale utente

TimeLine

TimeLine Micro Lynx VITC Option Card Manuale utente

TimeLine

TimeLine Lynx Keyboard Control Unit Manuale utente

TimeLine

TimeLine Micro Lynx ACG-1 Option Card Manuale utente

TimeLine

TimeLine Micro Lynx M3 Option Card Manuale utente

TimeLine

TimeLine Micro Lynx M3 Option Card Manuale utente

Manuali Apparecchiature di registrazione popolari di altre marche

KV2 Audio

KV2 Audio 500 Series Manuale utente

Robotics Technologies

Robotics Technologies microBus-Cam II Manuale utente

Seca

Seca 460 Manuale utente

Cognex

Cognex MVS-8000 Series Manuale utente

Mect

Mect MPNC006 Series Manuale utente

Bad Caf

Bad Caf THE LEASH Manuale utente

Strymon

Strymon NIGHTSKY Manuale utente

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuale utente

Tews Technologies

Tews Technologies TPMC465 Manuale utente

Honeywell

Honeywell Excel 50 Manuale utente

SeaLevel

SeaLevel COMM+8.LPCI Manuale utente

Arturia

Arturia AUDIOFUSE STUDIO Manuale utente

Rukra

Rukra RK-1240 Manuale utente

Samson

Samson SCOM Manuale utente

Dynacord

Dynacord DPS260 Manuale utente

Nice

Nice Core Manuale utente

Pyle Pro

Pyle Pro PSS8 Manuale utente

RF-System

RF-System TinyGate Manuale per l'uso e la cura