TimeTec Smart AC1/TD Manuale utente
User Guide
w w w . t i m e t e c c l o u d . c o m
Smart AC1/TD
Face Recognition Access Device with Fever Detection
2Smart AC1/TD
w w w . t i m e t e c c l o u d . c o m
COPYRIGHT NOTICE
All rights reserved. No part of this book may be reproduced or transmitted in any form or by any means, elec-
tronic or mechanical, including photocopying, recording, or by any information storage and retrieval system,
without written permission from TimeTec Holding. Every precaution has been made to supply complete and
accurate information. Information in this document is subject to change without prior notice.
DISCLAIMER
No person should rely on the contents of this publication without rst obtaining advice from a qualied profes-
sional person. The company expressly disclaims all and any liability and responsibility to any reader or user of
this book, in respect of anything, and of the consequences of anything, done by any such person in reliance,
whether wholly or partially, upon the whole or any part of the contents of this book.
TimeTec Cloud
3
Smart AC1/TD
w w w . t i m e t e c c l o u d . c o m
TABLE OF CONTENTS
1 NOTICE FOR USE 5
1.1 Finger Positioning 5
1.2 Standing Position, Facial Expression And Standin Posture 5
1.3 Palm Registration 6
1.4 Face Registration 6
1.5 Standby Interface 7
1.6 Virtual Keyboard 7
1.7 Verification Mode 8
• Palm Verification 8
• Fingerprint Verification 9
• Facial Verification 10
• Password Verification 11
• Combined Verification 12
2 MAIN MENU 13
3 USER MANAGEMENT 14
3.1 Adding Users 14
3.2 Search For Users 16
3.3 Edit Users 16
3.4 Deleting Users 17
4 USER ROLE 18-19
5 COMMUNICATION SETTINGS 20
5.1 Network Settings 20
5.2 Pc Connection 21
5.3 Cloud Server Setting 21
5.4 Wiegand Setup 22-24
6 SYSTEM SETTINGS 25
6.1 Date And Time 25
6.2 Access Logs Setting 26
6.3 Face Parameters 27-28
6.4 Fingerprint Parameters 29
6.5 Palm Parameters 30
6.6 Factory Reset 30
4Smart AC1/TD
w w w . t i m e t e c c l o u d . c o m
7 PERSONALIZE SETTINGS 31
7.1 Interface Settings 31
7.2 Voice Settings 32
7.3 Bell Schedules 32
7.4 Punch States Options 33
7.5 Shortcut Keys Mappings 34
8 DATA MANAGEMENT 35-36
9 ACCESS CONTROL 37
9.1 Access Control Options 38
9.2 Time Schedule 39
9.3 Holiday Settings 40
9.4 Combined Verification Settings 41
9.5 Anti-passback Setup 42
9.6 Duress Options Settings 43
10 ATTENDANCE SEARCH 44-45
11 AUTOTEST 46
12 SYSTEM INFORMATION 47
13 CONNECT TO SOFTWARE 48
13.1 Connect to AWDMS/ Ingress Software 48
13.2 Software Quick Installation 48-51
13.3 Configure AWDMS Setup Tool 52-53
13.4 Configure AWDMS in Ingress Software 54
APPENDIX 55-57
5
Smart AC1/TD
w w w . t i m e t e c c l o u d . c o m
1 Notice for Use
1.1 Finger Positioning
Recommended fingers: index, middle, or ring fingers; avoid using the thumb or
pinky, as they are difficult to accurately pressed onto the fingerprint reader
Note: Please use the correct method
when pressing your fingers onto the
fingerprint reader for registration and
identification. Our company assumes
no liability for recognition issues that
may result from the incorrect usage of
the product. We reserve the right of the
final interpretation and modification
concerning this point.
1.2 Standing Position, Facial Expression And
Standing Posture
The recommended distance between the device and a user
whose height is within 1.55m-1.85m is 1.5m. Users may slightly
move forwards and backwards to improve the quality of facial
images captured.
Facial expression and standing posture
Note:
During enrol-
ment and veri-
fication, please
remain natural
facial expression
and standing
posture.
Too low Too close
to the
edge
Vertical
6Smart AC1/TD
w w w . t i m e t e c c l o u d . c o m
1.3 Palm Registration
Place your palm in the palm multi-mode collection area, such that the palm is placed
parallel to the device.
Make sure to keep space between your fingers.
Note: Place your palm within
30-50cm of the device.
1.4 Face Registration
Try to keep the face in the centre of the screen
during registration. Please face the camera and
stay still during face registration. The page looks
like this:
Correct face registration and authentication
method
Cautions for registering a face
When registering a face, maintain a distance of 40cm to
80cm between the device and the face.
Be careful not to change the facial expression. (smiling
face, drawn face, wink, etc.)
If you do not follow the instructions on the screen, the
face registration may take longer or may fail.
Be careful not to cover the eyes or eyebrows.
Do not wear hats, masks, sunglasses or eyeglasses.
Be careful not to display two faces on the screen. Register
one person at a time.
It is recommended for a user wearing glasses to register both faces with and without glasses.
Cautions for authenticating a face
Ensure that the face appears inside the guideline displayed on the screen of the device.
If glasses have been changed, authentication may fail. If the face without glasses has been
registered, authenticate the face without glasses. If only the face with glasses has been regis
tered, authenticate the face with the previously worn glasses again.
If a part of the face is covered with a hat, a mask, an eye patch, or sunglasses authentication
may fail. Do not cover the face, allow the device to recognize both the eyebrows and the
face.
7
Smart AC1/TD
w w w . t i m e t e c c l o u d . c o m
1.5 Standby Interface
After connecting the power supply, enter the following standby interface:
Note:
1 Click to enter the User ID input interface.
2 When there is no super administrator set in the device, click
to enter the menu. After setting the super administrator, it requires
the super administrator’s verification before entering the menu op
eration. For the security of the device, it is recommended to register
super administrator the first time you use the device.
3 The switch of punch state can
be done directly by using the
screen shortcut keys. Click
anywhere on the screen
without icons, and six
shortcut keys appear, as
shown in the figure below:
Press the corresponding shortcut key to select the
current punch state, which is shown in green. Please
refer to “7.5 Shortcut Key Mappings” below for the
specific operation method.
1.6 Virtual Keyboard
Note:
The device supports the input of Chinese, English, numbers and symbols.
Click [En] to switch to English keyboard. Press [123] to switch to the nu-
meric and symbolic keyboard, and click [ABC] to return to the alphabetic
keyboard. Click the input box, virtual keyboard appears. Click [ESC] to exit
the input.
8Smart AC1/TD
w w w . t i m e t e c c l o u d . c o m
1.7 Verification Mode
Palm Verification
1: N Palm Verification mode
Compare the palm image collected by the palm
collector with all the palm data in the device.
The device will automatically distinguish be-
tween the palm and the face verification mode,
and place the palm in the area that can be col-
lected by the palm collector, and the device will
automatically detect the palm verification mode.
1: 1 Palm Verification mode
Click the button on the main screen to enter 1:1
palm verification mode.
Input the user ID and press [OK].
If the user has registered the face and password
in addition to his/her palm, and the verification
method is set to palm/ face/ password verifica-
tion, the following screen will appear. Select
the palm icon to enter palm verification
mode.
9
Smart AC1/TD
w w w . t i m e t e c c l o u d . c o m
Fingerprint Verification
1: N fingerprint verification mode
Compares the fingerprint that is being pressed onto the fingerprint reader with all of
the fingerprint data that is stored in the device.
The device will enter the fingerprint authentication mode when a user presses his/her
finger onto the fingerprint scanner.
Please follow the correct way to place your finger onto the sensor. For details, please
refer to section 1.1 Finger Positioning.
1: 1 fingerprint verification mode
Compares the fingerprint that is being pressed onto
the fingerprint reader with the fingerprints that are
linked to User ID input via the virtual keyboard.
Users may try verifying their identities with 1:1 veri-
fication mode when they cannot gain access with 1:
N authentication method.
Click the button on the main screen to enter
1:1 fingerprint verification mode.
1. Input the user ID and press [OK].
10 Smart AC1/TD
w w w . t i m e t e c c l o u d . c o m
If the user has registered face and password in addition
to his/her fingerprints and the verification method is
set to fingerprint/ password/ face verification, the fol-
lowing screen will appear. Select the fingerprint icon
to enter fingerprint verification mode.
2. Press the fingerprint to verify.
3. Verification is successful.
4. Verification is failed.
Fingerprint Verification
1:N Facial Verification
Conventional verification: Compare the acquired facial images with all face data
registered in the device. The following is the pop-up prompt box of comparison result.
1:1 Facial Verification
Compare the face captured by the camera with the facial template related to the
entered user ID.
Altri manuali per Smart AC1/TD
1
Indice
Altri manuali TimeTec Controllori di accesso IP
