Timing TSC 4037A Manuale utente

4037A Operations and Maintenance Manual 1

TSC 4037A

1 x 16 L1/L2 Distribution

Amplifier

Operations and Maintenance

Manual

4775 Walnut Street

Suite 1B

Boulder, CO 80301

USA

www.timing.com

Phone: (303) 939-8481

TSC 4037A 1 x 16 L1/L2 Distribution Amplifier Operations and Maintenance Manual

Timing Solutions is a trademark of the Timing Solutions Corporation.

Other product and company names may be trademarks of their respective owners.

DOC04037A Rev C

Revision History

Revision Description Date Approved

A Initial Release 26 Oct 2004 GAR

B Add jumper information 28 June 2005 GAR

C Change default jumper setting,

add D.O.C. and additional

specs.

25 May 2006 GAR

4037A Operations and Maintenance Manual 3

1: Introduction ............................................................................................................... 4

1.1 Symbols............................................................................................................................................... 4

1.2 About This Manual ............................................................................................................................. 5

1.2.1 Conventions ................................................................................................................................. 5

1.3 4037A Overview ................................................................................................................................. 6

2: Installing and Setting Up the 4037A ........................................................................ 7

2.1 Safety First!......................................................................................................................................... 7

2.2 Unpacking ........................................................................................................................................... 7

2.3 Cleaning .............................................................................................................................................. 8

2.4 Installing the 4037A............................................................................................................................ 8

2.4.1 Required materials for installation ............................................................................................... 8

2.4.2 Making Connections .................................................................................................................... 8

2.4.3 Input Signal and antenna bias setting........................................................................................... 9

3: Troubleshooting the 4037A.................................................................................... 10

3.1 Replacing Fuses ................................................................................................................................ 10

3.2 Solving Operational Problems .......................................................................................................... 10

4: Warranty and Shipping Information ...................................................................... 11

4.1 Warranty Information ....................................................................................................................... 11

4.2 Shipping Information ........................................................................................................................ 11

4.2.1 Packing Instructions................................................................................................................... 11

5: Declaration of Conformity ...................................................................................... 12

Appendix A: Specifications........................................................................................ 13

Glossary....................................................................................................................... 15

Index............................................................................................................................. 16

1: Introduction

Note

FIRST READ THIS MANUAL THROUGHLY!

This is especially true for the sections regarding Safety and Installation.

1.1 Symbols

These symbols appear throughout the manual as well as on the unit itself.

Note

This symbol means the following information is a note that gives you

important information that may affect how you use the 4037A.

Caution, refer to manual. Read all instructions in Manual

before using this product.

Caution – Risk of Electrical shock

Fuse symbol

Earth terminal symbol: Used to indicate an earth ground

connection to chassis.

4037A Operations and Maintenance Manual 5

1.2 About This Manual

This manual tells you how to install, set up, monitor, and troubleshoot the 4037A.

“Chapter 1, Introduction” explains symbols that appear in the manual and on the unit as well as

documentation conventions. The chapter also briefly describes the 4037A.

“Chapter 2, Installing and Setting Up the 4037A” contains important safety information and

describes how to install the 4037A.

“Chapter 3, Troubleshooting the 4037A” describes how to replace fuses and verify operational

problems.

“Chapter 4, Warranty and Shipping Information” explains how to contact Timing Solutions

Corporation for warranty service and provides shipping guidelines.

“Appendix A, Specifications” contains the detailed specifications for the 4037A.

1.2.1 Conventions

This manual uses several typographical conventions to help explain how to use the 4037A.

Convention Definition

Bold Words in bold show:

!Buttons and icons to click

!Menu options to select

!Commands to type

!Non-variable information displayed in response to commands

Italics Words in italics show:

!Names of windows and dialog boxes

!Variable information displayed in response to commands

1.3 4037A Overview

The TSC 4037A is a one input, sixteen output L1/L2 amplifier housed in a 1U (1.75”) high 19 inch rack mount

chassis. It provides sixteen outputs from a single input. The front panel provides green LED status for the voltage

being supplied to the antenna (5V or 12V). Additionally, there is a green LED that provides power status.

Figure 1 shows the 4037A’s front panel, and Figure 2 shows the 4037A’s rear panel.

Figure 1: Front panel

Figure 2: Rear panel

4037A Operations and Maintenance Manual 7

2: Installing and Setting Up the 4037A

2.1 Safety First!

Warnings:

This unit is for INDOOR USE ONLY. It is not protected against a harmful ingress of moisture.

Do not attempt to install or operate this equipment if you have not first acquired proper training.

Equipment is intended to be installed in an Enclosed or Open type equipment rack

Ensure that all cables are properly connected. The power cord must be easy to remove from the

back.

Verify that input line voltage and current capacity are within specifications before turning on

power to the unit.

Disconnect all sources of input power before removing the top cover of this unit.

Operating and maintenance personnel must receive proper training before installing or

maintaining electrical equipment.

2.2 Unpacking

To unpack the TSC 4037A unit:

1. Unpack and carefully inspect the unit.

2. Check for physical damage.

3. If no physical damage is apparent, then proceed with making appropriate connections.

!If physical damage is observed, immediately contact Timing Solutions and the

carrier.

4. Save the shipping container for submitting any necessary claims to the carrier.

2.3 Cleaning

Warning

Do not spray or use too much liquid when cleaning the unit. Liquid can enter the unit and damage

sensitive electronic components.

Clean the main chassis with a soft cloth dampened with a mild soap and water solution.

2.4 Installing the 4037A

The 4037A is shipped ready for installation into a standard 19" (48.3 cm) rack. Provisions are

included for mounting General Devices slides with part numbers C-300-S-126, -128 and -130.

2.4.1 Required materials for installation

North American or European IEC power cord. One or the other will be supplied with the unit.

Customer supplied double-shielded RG223 cables with TNC connectors from source, and to

next devices in system.

Rack-mount slide kit from General Devices, C-300-S-126, -128 or -130 (Optional)

Rack mounting screws, screwdriver, and slide as needed.

2.4.2 Making Connections

2.4.2.1 Input Power

AC INPUT POWER - The input power to the unit is supplied through a detachable 3-prong

power cable. First plug the female end into the male IEC-320 plug on the rear of the unit,

then plug the male end of the cable into a 100V~ to 240V~, 50/60 Hz power source.

Warning

Ensure that this power supply cord is connected to a properly grounded mains receptacle to

ensure safety.

Since the unit does not have an AC Mains Power Switch, both the Appliance Inlet Connector

and the Plug on the detachable type power supply cord are considered to be suitable

Disconnect Means for disconnecting the unit from the AC Mains Supply. If the rear of the

unit is not accessible after installation in the instrument rack, the User is responsible for the

provision of a suitable external AC Disconnect Means for the unit.

4037A Operations and Maintenance Manual 9

2.4.2.2 Output Signals

Connect up to sixteen cables to the OUTPUT TNC connectors on the rear panel of the unit to

supply users with a copy of the input signal.

2.4.3 Input Signal and antenna bias setting

Before connecting the antenna input signal, ensure that the antenna bias supply voltage

jumper is set to the position which will provide the proper voltage to your antenna. There are

three different settings for the antenna voltage: +5 VDC, +12 VDC and no DC voltage

supplied. The unit ships from the factory with a default setting of no DC voltage. To change

the setting; remove the top panel from the unit, locate jumper JP1 and place it in the position

to provide the appropriate voltage. If you do not want to supply a DC voltage to your

Antenna, place the jumper on JP2 for future use if you need to supply a voltage to the

antenna.

Connect the input signal cable to the INPUT TNC connector on the back of the unit.

Perform all of the following procedures before returning the unit for service. If the unit still

appears to have a problem, then call Timing Solutions Corporation and request technical support.

Have the serial number of your unit ready to provide to a technical representative.

3.1 Replacing Fuses

If you know that a local event caused blown fuses throughout a rack, you can replace the fuses in

each 4037A power entry module.

Required for this procedure:

!Small flat-head screwdriver

!Replacement fuse for a standard IEC 320 power entry module with fuse (5 x 20 mm, 1 A

250 V Time lag fuse)

To replace a fuse:

1. Disconnect the power cable from the back of the 4037A.

2. Using a small screwdriver, open the fuse cover on the back of the 4037A.

3. Replace the old fuses as necessary.

4. Close the fuse cover.

5. Reconnect the power cable to the back of the 4037A.

3.2 Solving Operational Problems

If the unit does not operate properly after you have verified that:

!the correct power is applied to the rear of the 4037A

and

!the fuses are good,

call Timing Solutions Corporation to obtain a Returned Materials Authorization and return the

unit to TSC for repair.

3: Troubleshooting the 4037A

Indice

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente