Tiny Audio C6 Manuale utente

Side 1

English

TINY AUDIO C6

Please read carefully before using this product

Side 2

Safety Instructions:

1. Do not use this radio near water.

2. Clean with dry cloth.

3. Do not block any ventilation openings.

4. Do not use near heat objects.

5. Use accessories provided by manufacturer.

6. Do not dispose this radio to rain or moisture.

7. Do not allow this unit to be exposed to water,

steam, sand or other environmental hazards.

8. Do not leave your radio where excessive heat

could cause damage.

Side 3

Controls:

1. PRESET Button

2. MENU Button

3. MODE Button

4. TX/SCAN Button

5. Tuning Knob and Confirmation Button

6. Stand Holder Slot

7. Power ON/OFF Switch

8. Power Supply Cable Socket

9. 3.5mm Line In or Line Out Jack

10. Antenna Jack

Side 4

Main Unit and Accessories:

1. Main unit, DAB receiver

2. Power cable/Micro USB

3. 3.5mm Aux cable

4. DAB, DAB+ antenna for main unit

5. Dash/window mounting bracket

6. Dual USB charger for 12/24V

Note: All accessories are designed to work

specifically with Tiny Audio C6. Please do not

use third party cables as these may not work

and cause warranty invalidation.

Side 5

Operating your In-Car DAB+ Digital Radio Receiver:

1. Mount the TINY AUDIO C6In-Car DAB+ Radio receiver to

the dashboard using the provided adhesive holder.

2. Connect one end of the USB power supply cable to Micro

USB socket in TINY AUDIO C6and the other end to dual

USB car charger. Plug the dual USB car charger to the car

cigar-lighter socket.

3. Connect the antenna to the antenna jack. ATTENTION!

Proper antenna installation is very important for a good

result. See tips page 17.

4. Turn on the power with the “POWER SWITCH” and the

display will show “Tiny Audio” logo, then the device will

automatically scan all the local DAB/DAB+ channels and

store them in the memory of the device until another

“Auto Scan” is performed. During scanning, a scan moving

bar will be shown in the display to indicate the progress

and the total number of channels received.

5. Once it is scanned, you can select any DAB+ radio

channels by the Tuning Knob.

Receive signal from the In-Car DAB+ radio through line out

cable:

1. Press and hold “MENU” button to enter menu mode, use

Tuning Knob to search for “AUX IN/OUT Select” and

confirm by pressing Tuning Knob. Use Tuning Knob to

Side 6

select “AUX OUT” and confirm by pressing Tuning Knob.

Short press “MODE” button to exit menu. A headphone

icon “ ” will be displayed at the top of the blue bar.

2. Connect your car audio stereo speaker “Aux-in” or

“Line-in” to the “LINE OUT” jack on the right-hand side of

TINY AUDIO C6 with the provided 3.5mm audio cable.

Remark: In “AUX OUT” mode, there will be no FM transmission to

the car stereo.

Receive signal from the In-Car DAB+ radio through FM

transmission:

--Select FM Transmitting Frequency (Auto Mode):

1. Press and hold “MENU” button to enter menu mode,

use Tuning Knob to search for “AUX IN/OUT Select”

and confirm by pressing Tuning Knob. Use Tuning

Knob to select “AUX IN” and confirm by pressing

Tuning Knob.

2. Press “TX/SCAN” button to show FM transmitting

frequency (TX FREQ).

3. Then press and hold “TX/SCAN” button for 2 seconds

to activate the automatic scanning of a “vacant”

transmission frequency without interference with

other channels. The scanning process will take 5-6

seconds to scan the frequency automatically with a

Side 7

flashing display of “---.-MHZ” and stop at a “vacant”

frequency.

4. After a “vacant” frequency is found, press “TX/SCAN”

button again to confirm and exit setting or it will

automatically confirm and exit the setting after 5

seconds. The selected “vacant” frequency (TX FREQ)

will be shown at the top of the blue bar, e.g.

TX108.0MHz

5. Then tune your car FM radio system to match the

selected “vacant” frequency (TX FREQ) for

transmission of the audio signal from TINY AUDIO C6

to your car stereo audio system.

Remark: To enable FM transmitter, you have to set the device

into “AUX IN” mode.

--Select FM Transmitting Frequency (Manual Mode):

1. Press “TX/SCAN” button to enter FM transmitting

frequency selection mode.

2. Then use Tuning Knob to select your favorite vacant

frequency (based on your past experience with the

known vacant frequency) which you would like to

receive by your car radio.

3. Once it is selected, press “TX/SCAN” button to

confirm and exit or the screen will go back to DAB+

mode automatically after 5 seconds and the selected

Side 8

frequency will be shown at the top of the blue bar,

e.g. TX108.0MHz.

Remarks:

“Vacant frequency” means there is no any radio broadcasting

content or noise when the frequency is selected.

Search and select DAB+ channels:

1. Press the “MODE” button until “DAB+ Radio” mode is

found.

2. Use Tuning Knob to select the desired DAB+ channel.

3. Or press “MENU” button to enter Preview Mode, use

Tuning Knob to scroll up or down to select the desired

DAB+ channel and press Tuning Knob to select.

4. You may also press and hold the “MENU” button to

enter menu, use Tuning Knob to select for “DAB

Autoscan” and confirm by pressing Tuning Knob to

re-activate the “Auto Scan” process if you need to

update the DAB+ radio channels.

Remark: For normal use, you don’t have to perform the “Auto

Scan” every time you use the car DAB+ radio unless there are

newly added DAB+ channels, then you may need to perform

the “Auto Scan” again. The scanning operation is similar to

your home TV set.

Side 9

Service Information: DAB+ mode

The Service Information display -The Service Information data

will be displayed with scrolling text which is being broadcasted

from the station.

While listening to DAB+, the display will show the followings if

applicable.

1. Channel Name

2. Frequency

3. Multiplex Name（DLS）

4. DAB+ icon

5. Number of Channel Scan and Stored

6. Signal Strength

7. FM Transmitting Frequency

8. AUX IN or AUX OUT status

9. Service Following On status

Service Following ON/OFF Control:

1. Press the “MODE” button until “DAB+ Radio” mode

is found.

2. In “DAB” mode, press and hold the “TX/SCAN”

button to turn ON the service following function. A

“S/F” will displayed on the LCD screen. Repeat the

same procedure to turn OFF the service following

function and “S/F” will also disappear from the LCD

screen.

Side 10

Manage the Preset Stations:

Storing the Preset Stations:

To program and store your favorite DAB+ preset stations:

1. To select a favorite DAB+ station using Tuning Knob.

2. Press and hold “PRESET” button for 3 seconds to enter

“Store Preset” mode.

3. Use Tuning Knob to scroll up or down to select a

number in memory to store your favorite station.

4. Press Tuning Knob to confirm and exit “Store Preset”

mode. A message “Stored Successfully” will be

displayed.

Recalling the Preset Stations:

To recall your favorite DAB+ preset stations:

1. Press “PRESET” button to enter “Select Preset”

mode.

2. Use Tuning Knob to scroll up or down to recall a

Preset Station.

3. Press Tuning Knob to confirm and exit “Select

Preset” mode.

Indice

Lingue:

Altri manuali Tiny Audio Impianto stereo per auto

Tiny Audio

Tiny Audio C-SMART Manuale utente

Manuali Impianto stereo per auto popolari di altre marche

JL Audio

JL Audio Stealthbox SB-CAN-G2MVX3D/10TW3 Manuale utente

Clarion

Clarion PU-9836A Manuale utente

Sony

Sony MEX-BT5750U Manuale utente

Mitsubishi Electric

Mitsubishi Electric AR0M Manuale utente

Sony

Sony RM-X7BT Manuale utente

Insignia

Insignia NS-HD5113 Manuale utente

Clarion

Clarion BTD3341 Manuale utente

USA SPECS

USA SPECS PA11-VW6 Manuale utente

Sony

Sony MEX-N4380BT Manuale utente

Kenwood

Kenwood KCD-BT6544U/UY Manuale utente

JVC

JVC KD-DB912BT Manuale utente

Philips

Philips CSQ405/98 Manuale utente

Alpine

Alpine TDM-7544 Manuale utente

Autotek

Autotek TransAm TA 1400 Manuale utente

Clarion

Clarion PN-3124N-A Manuale utente

Denso TEN

Denso TEN FT0108A Manuale utente

Pyle

Pyle PLD57MU Manuale utente

Harman

Harman Chrysler Radio Navigation System RB4 Manuale utente