Tiptop Audio MISO Manuale utente
www.tiptopaudio.com
1+2
A+B
1 IN
2 IN
A IN
B IN
OUTS
MISO User Manual
MISO stands for
Mix
Invert
Scale
Oset
Mix: Mix and sum signals
Invert: Invert signal while performing gain
Scale: Gain for signal
Oset: Adds a static DC voltage to signal
MISO is a utility module by Tiptop Audio that can be used in multiple ways: scale and invert
up to four independent signals, oset four independent signals, mix four signals, and
crossfade between signals.
MISO can be used to process all the signals you will find in a Eurorack setup: CV, Audio,
Gates and Triggers. MISO can be used in a planned manner to adjust and craft signals in
details or used without planning for blending signals for inspiring and unexpected results
1+2
A+B
1 IN
2 IN
A IN
B IN
OUTS
Here you can see a visualization of MISO’s functions.
MIX = 1+2
Scale & Invert
Oset
MIX
There are two MISO sections in each MISO module, one on the top and one on the
bottom. Top MISO is labeled 1and 2. Bottom MISO is labeled Aand B. Both top and
bottom sections of MISO are identical and can be used independently. At the center of the
module is a voltage controlled crossfader allowing you to mix between the top and
bottom section of MISO.
1+2
A+B
1 IN
2 IN
A IN
B IN
OUTS
Top MISO
Crossfader
Bottom MISO
Each MISO contains two channels (1/2 + A/B).
Each channel has:
IN jack (Input)
Scale / Invert knob
Oset knob
OUT jack (Output)
A Mix Out jack provides the mix of thennels. The LED indicates the mix output level and
polarity, yellow is positive voltage and red is negative voltage.
1+2
1 IN
2 IN
OUTS
Top MISO
Channel 1
1+2
1 IN
2 IN
A IN
OUTS
Top MISO
Channel 2
1+2
A+B
1 IN
2 IN
A IN
B IN
OUTS
Channel 1 Input
Channel 2 Input
Channel 1 Offset
Channel 2 Offset
Channel 1 Output
Channel 2 Output
Channel 1+2 Mix Out
All together, MISO signal ow looks like this:
IN 1 OUT1
SCALE
INVERT OFFSET
IN 2 OUT2
SCALE
INVERT OFFSET
IN A OUTA
SCALE
INVERT OFFSET
IN B OUTB
SCALE
INVERT OFFSET
VC
CROSSFADER OUT
CROSSFADE
MIX 1+2
MIX
MIX
MIX A+B
CROSSFADER
Here are some oscilloscope images. At the input is a sawtooth wave from a Z3000 VCO
into IN1, and the output at OUT1.
Here are some oscilloscope images.
IN 1 is a sawtooth wave and IN 2 is a sine wave, both from the Tiptop Audio Z3000 VCO.
At the center, in green, is the combined output of MIX 1+2.
Let’s get started.
1 Set all the knobs on MISO to the center, 12 o'clock, all LEDs are OFF.
2 Patch channel 1 OUT to CV IN on your filter.
3 Patch audio into the filter IN and the filter OUT to your speakers.
4 Turn channel 1 Oset knob, it will open and close your filter. This is the Oset
generator, it is working as a manual CV generator.
1+2
A+B
1 IN
2 IN
A IN
B IN
OUTS
BP INHP IN LP IN
VOLUME
AUDIO SOURCE
SOUND SYSTEM
Reset the MISO oset to center.
1 Patch a Sawtooth wave from your Z3000 (or any other LFO) to channel 1 IN jack
2 Set the Z3000 to LFO, start turning the Scale/Invert knob to the right and the
Sawtooth starts opening the filter.
3 Turn the knob the other way around and the signal gets inverted.
4 Re-adjust the cuto knob on your filter to get a feel for it.
1+2
A+B
1 IN
2 IN
A IN
B IN
OUTS
BP INHP IN LP IN
VOLUME
SOUND SYSTEM
LFO
SOUND SYSTEM
AUDIO SOURCE
Indice
