Titan MNRSPRDRv2 Manuale utente
MANURE SPREADER
MNRSPRDRv2
191396
Operator’s Manual
Read the Operator’s Manual entirely. When you see this
symbol, the subsequent instructions and warnings are
serious follow without exception. Your life and the lives
of others depend on it!
2
GENERAL WARNING
GENERAL WARNINGS
READ and UNDERSTAND this manual completely before using the Manure Spreader.
Operators must read and understand all safety and warning information, operating
instructions, maintenance, and storage instructions before operating this equipment.
Failure to properly operate and maintain the manure spreader could result in serious
injury to the operator or bystanders.
OPERATION WARNINGS
•Never carry passengers.
•Do not sit or stand on the manure spreader.
•Do not allow children to play on, stand upon or climb on the manure spreader.
•Always inspect the manure spreader before use for missing or loose hardware.
•Replace or repair damaged or worn parts immediately.
•Always check and tighten hardware and assembled parts before operation.
•Avoid large holes and ditches when transporting loads. Be careful when operating on
steep grades (hills) as the manure spreader may tip over.
•Do not pull close to creeks, ditches, or public highways.
•Do not use the manure spreader in windy conditions.
•Always use caution when loading and unloading the manure spreader.
•Only tow the manure spreader using a lawn tractor, ATV or golf cart at a speed of no
greater than 5 mph for spreading. Crush and Cut Hazards
•Always keep hands and feet clear from moving parts while operating the manure
spreader.
•Always keep the work area clean and clear of debris.
•Always wear safety gear, eye protection, gloves and work boots while operating the
manure spreader.
CRUSH AND CUT HAZARDS
▪Always keep hands and feet clear from moving parts while operating the manure
spreader.
▪Always keep the work area clean and clear of debris.
▪Always wear safety gear, eye protection, gloves and work boots while operating the
manure spreader
3
WARNING
The warning, cautions, and instructions outlined in the instruction manual cannot cover
all possible conditions or situation that may occur. It must be understood by the
operator that common sense and caution are factors which cannot be built into this
product and must be supplied by the operator
PROP 65 WARNING
This product can expose you to chemicals including lead and lead compounds which are
known to the State of California to cause cancer and birth defect or other reproductive
harm. For more information go to www.P65Warnings.ca.gov
ASSEMBLY IS REQUIRED
This product requires assembly before use. See “Assembly” section for instructions. INSPECT
ALL COMPONENTS closely upon receipt to make sure no components are missing or damaged.
HAZARD SINGNAL WORD DEFINITIONS
This is the SAFETY ALERT SYMBOL. It is used to alert
you to potential personal injury hazards, obey all
safety messages that follow this symbol to avoid
possible injury.
DANGER indicates an imminently hazardous situation
which, if not avoided, will result tin death or serious
injury.
WARNING indicated. A potentially hazardous
situation which, if not avoided, could result in death
or serious injury.
CAUTION indicated a potentially hazardous situation
which, if not avoided, may result in minor moderate
injury.
CAUTION used without the safety alert symbol
indicated a potentially hazardous situation which, if
not avoided, may result in minor moderate injury.
4
CONTROLS AND FEATURES IDENTIFICATION
Read this owner’s manual before operating the equipment. Familiarize yourself with the
location and function of all the controls and features. Please save this manual for future
reference.
1. Hopper
2. 2” Coupler
3. Spreading Drum
4. Spreading Engagement Lever
5. Agitator
6. Relief Panel
CAUTION
Read and follow all instruction for assembly and operation. Failure to properly assemble
this equipment could result in serious injury to the user or bystanders and/or cause
equipment damage.
5
ASSEMBLY INSTRUCTIONS
MANURE SPREADER COMPONENT PARTS AND ASSEMBLY
Before beginning to assemble the manure spreader, take all parts out of the shipping crate and
inspect components to ensure there are no missing pieces. Carefully follow assembly steps 1
through 2.
TOOLS REQUIRED
• 10mm, 13mm, 17mm, 19mm Wrenches
• Screwdriver
STEP 1: CONNECT SIDE PLATES
Connect right side plate (#17), left side plate (#22), rear plate (#16) and front plate (#58) using
step bolt M6x12 (#18) and nylon lock nut M6 (#19).
6
STEP 2: ATTACH PRESSING PLATE
Attach discharge plate (#24) to the hopper assembly using hex bolt M8x20 (#21), lock washer Ø8
(#39) and flat washer Ø8 (#27).
STEP 3: ATTACH THE DISCHARGE PLATE
Attach discharge plate (#24) to the hopper assembly using hex bolt M8x20 (#21), lock washer Ø8
(#39) and flat washer Ø8 (#27).
7
STEP 4: ATTACH THE AXLE WELDMENT
Put the axle weldment (#53) through the roller assembly (#54), then insert sleeve 14 (#50) and
rolling bearing (#51), then tighten the screw in the rolling bearing.
STEP 5: ATTACH ROLLER ASSEMBLY
Attach roller assembly to the hopper assembly using hex bolt M12x40 (#35), flat washer Ø12
(#4) and nylon lock nut M12 (#5). At the same time, insert about 5mm plates between the rollers
on both sides and the side plates of the hopper, and then move the roller as far as possible to
the hopper. Lock the bolt after visual inspection of each gap is reasonable. Finally, pull out the
plates inserted between the roller and the side plates.
8
STEP 6: ATTACH WHEELS
Attach sleeve (#50) and wheel (#46) to the wheel axle, then attach clutch assembly to the wheel
axle using hex bolt M8x60 (#60), clutch spring (#55), large flat washer Ø8 (#27) and nylon lock
nut M8 (#11). Turn the nylon lock nut M8 to adjust the spring tightness to the right position.
STEP 7: ADJUST THE DISCHARGE PLATE
Adjust the discharge plate assembly by moving it up and down to ensure that the gap between
the discharge plate and the roller is between 3-5mm. Tighten the bolt to lock the discharge plate
assembly.
9
STEP 8: ATTACH THE AGITATOR ASSEMBLY
Attach the agitator assembly to the hopper, place sleeve 5 (#36) on the hopper, then lock it with
hex bolt M8x20 (#21) and nylon lock nut M8 (#11). Ensure that the fixed plate can be easily
rotated.
4
STEP 9: ATTACH TOW BAR
Attach tow bar (#15) to the side plate using M8x16 carriage bolt (#20) and M8 nylon lock nut
(#11).
10
STEP 10: ATTACH COUPLER ASSEMBLY
Attach coupler assembly to the tow bar using M10x75 Hex Bolt (#12), Ø10 flat washer (#13) and
M10 nylon lock nut (#14).
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Titan Spargitore
Manuali Spargitore popolari di altre marche
Fisher
Fisher POLY-CASTER 78601 Manuale utente
TurfEx
TurfEx RS7200 Manuale del proprietario
Ferris
Ferris Pathfinder Series Manuale utente
Fayat Group
Fayat Group DYNAPAC S100 Guida alla risoluzione dei problemi
Art's-Way Manufacturing
Art's-Way Manufacturing X700 Manuale di installazione e funzionamento
EASTMAN
EASTMAN CR 500 Manuale utente
