TLI VOLspeed Scheda tecnica

1144_BA_E_Rev2 - VOLspeed Bosch Active / Performance V3

VOLspeed Ebike Tuning

Bosch Active Line

Bosch Performance Line

Operating Manual

Installation Guide

1144_BA_E_Rev2 - VOLspeed Bosch Active / Performance V3

Attention!

Read these instructions completely before using the device, keep the

instructions and pass them on when handing over the device to other

persons.

Product Features

The device offers the following functions after installation in eBikes with Bosch drive system

(20 / 25 / 32 / 45 km/h):

Individual activation code adjustable

Speed limit adjustable via handlebar control buttons

Adjustable dynamic mode with reduced "wall effect"

Correct display of speed and distance

Correct mileage after removal of the tuning module

Optimized range calculation with active tuning

Battery indication in percent alternating with the range when tuning is active

Workshop mode

All settings are made via the handlebar control buttons on the eBike. No smartphone or

notebook is required.

The electronic is cast into the housing and thus safely protected against moisture.

Intended Use

The device is only suitable for installation in eBikes with the following Bosch drive systems:

Drive system:

Display type:

Active Line

Intuvia, Purion, Nyon, Kiox, Nyon2

Active Line plus

Intuvia, Purion, Nyon, Kiox, Nyon2

Performance Line

Intuvia, Purion, Nyon, Kiox, Nyon2

Performance Line CX

Intuvia, Purion, Nyon, Kiox, Nyon2

Cargo Line

Intuvia, Purion, Nyon, Kiox, Nyon2

Legal and Safety Notes / Product Liability

Operation of the eBike in public traffic is no longer permitted after installation of

the module. The use is only allowed on private areas or designated test and race

tracks.

Damage caused in conjunction with the operation of the eBike will no longer be

covered by private liability insurance after installation.

Liability and warranty claims against the dealer or manufacturer of the eBike expire

or are constricted.

1144_BA_E_Rev2 - VOLspeed Bosch Active / Performance V3

The eBike is subject to higher mechanical stress when operating at higher speed for

which it is not designed. This results in additional safety risks.

The installation and operation of the module is at your own risk. The manufacturer

accepts no liability for damage in connection with the installation or operation of

the unit.

Please inform yourself about possible further technical and legal consequences

before installing the device.

Technical Data

Housing dimensions: 37mm x 19mm x 9mm (1.46”x 0.75”x 0.36”)

Cable length: approx. 180mm (7”)

Weight: 0,025kg (0.9oz)

Power consumption: 0,2W

Supply voltage: 12VDC

Installation example Cube Reaction Hybrid Pro 500 / Bosch Performance CX 2020

Required tools:

Allen key 4mm

Procedure:

1. Remove battery

2. Remove the motor cover (Allen key 4mm).

1144_BA_E_Rev2 - VOLspeed Bosch Active / Performance V3

Depending on the bike model, the engine cover can also be attached

with Torx or Phillips screws.

With many covers it is also necessary to remove the crank. A suitable

crank puller is required for this.

3. Disconnect the cables at the green marked two sockets. Also, use the following

sketch as a guide for different motors. Remove the green marked connectors.

Attention!

Also pay attention to the color of the small connector.

Black: rear light

Blue: front light

Gray: speed sensor

1144_BA_E_Rev2 - VOLspeed Bosch Active / Performance V3

4. Connect the tuning module to the free sockets on the engine. Connect the previously

disconnected cables to the other connections of the tuning module.

5. Ensure that all connectors are fully inserted.

6. Write down the article number (P/N) and serial number (S/N) on the back of this

manual to have the data ready for possible support requests.

7. Insert the battery and carry out the initialization, see separate point “setup”(page 7).

8. If an individual activation code is to be set to protect the tuning from unauthorized

use, set it now, see point "Activation code" (page 11), otherwise continue in the next

step.

This point is optional. If you don't want to set a code, go to the

next step.

1144_BA_E_Rev2 - VOLspeed Bosch Active / Performance V3

9. Remove the battery again.

10. Place the tuning module in a suitable location and route the cables so that the

reassembly of cover is possible. In the picture, the module was pushed into the down

tube.

Due to the large number of different drive systems and covers,

it is not possible to define a fixed installation location. Often a

placement of the module directly in the connection area of the

motor is possible. A placement in the frame tube is also

possible, but in this case the motor must mostly be dismounted

from the frame.

11. Reassemble cover.

12. Activate the tuning as described in the chapter "speed mode" (page 9).

1144_BA_E_Rev2 - VOLspeed Bosch Active / Performance V3

Setup

Before the first use of the tuning module or after moving it to another bike the setup must

always be carried out first. Even in the case of malfunctions, the initial state of the module

can be restored by executing the setup.

The following illustrations show the Purion display. For the Nyon, Kiox or

Intuvia, press the corresponding buttons on the control unit.

Please set the display to km/h before. If set to mph you get different

readings during setup.

If an activation code is set, enter it now, otherwise continue.

Input example:

Code 32: press 3x “minus”, afterwards 2x “plus”.

Code 3: press 3x “plus”.

No code is set when new. Code is not displayed during input. Enter the

code quickly and proceed immediately to the next step. If you make a

mistake, wait 5 seconds before trying again.

3-5s

km/h

Press “minus”for 3 to 5 seconds.

Release “minus”button and within one second, press “plus”for 3

to 5 seconds.

Speed 11.1 km/h is displayed for 10 seconds.

Adjustment factor speed limit. Only adjust if there are problems,

see FAQ. If necessary, change within 5 seconds using the “plus”and

"minus" buttons. Possible values: 7.0..13.0 (= 70..130%). Default

value: 100%.

km/h

3-5s

km/h

10s

km/h

1144_BA_E_Rev2 - VOLspeed Bosch Active / Performance V3

If the display changes from 11.1 directly to 0.0, the wiring of the module is

faulty. The 2-pin connector to the motor is connected to the wrong socket.

Set the factory speed limit here or activate the workshop mode.

If necessary, change within 5 seconds using the “plus”and “minus”

buttons. Possible values: 20, 25, 32 (=20mph) and 45km/h, Default

value: 25.0. Set 1.0 for the workshop mode.

For a European e-bike, the factory speed limit is normally 25km/h. You do

not need to press anything in this case.

If you set a value that is too high, the tuning will not work. If the bike

supports up to 25km/h ex work you have to set 25km/h here.

As soon as setup displays 0.0 km/h, the setup is finished.

km/h

1144_BA_E_Rev2 - VOLspeed Bosch Active / Performance V3

Speed Mode

When speed mode is activated, the speed limit for the motor assistance is increased. The

limit can be set from 25

to 99 km/h (15.51to 61.5mph).

Turning off the eBike automatically turns off speed mode and must be reactivated after the

bike is turned on.

If the limitation is not removed despite being activated, the wrong eBike

type was set during setup. For eBikes that support up to 25 km/h without

tuning, the eBike type must also be set to "25".

Enable speed mode –No activation code set

Press "minus" for > 3 seconds while standstill or while driving.

Speed limit is displayed for 5 seconds. If desired, use the "plus" and

"minus" buttons to change. Possible values: 251to 99 km/h (15.5 to

61.5mph). Default value: 32 km/h (19.8mph). Set value will be

stored.

Display shows the normal driving speed again. Speed mode is

active.

Disable speed mode

Press "minus" for > 3 seconds.

Display shows the factory speed limit for 2 seconds. Speed mode is

off.

The lowest possible value is always the factory speed limit set during setup.

km/h

1144_BA_E_Rev2 - VOLspeed Bosch Active / Performance V3

Enable speed mode –Activation code set

Enter the activation code. Always press the minus keystrokes first,

then the plus keystrokes.

Input example:

Code 32: press 3x “minus”, afterwards 2x “plus”.

Code 3: press 3x “plus”.

Code is not displayed during input. Enter the code quickly and proceed

immediately to the next step. If you make a mistake, wait 5 seconds

before trying again.

Press "minus" for > 3 seconds.

Speed limit is displayed for 5 seconds. If desired, use the "plus" and

"minus" buttons to change. Possible values: 25

to 99 km/ h (15.5

to 61.5mph). Default value: 32 km/h (19.8mph). Set value will be

stored.

Display shows the normal driving speed again. Speed mode is

active.

The lowest possible value is always the factory speed limit set during setup.

km/h

Altri manuali per VOLspeed

Altri manuali TLI Accessori per biciclette

TLI

TLI VOLspeed Ebike Tuning Giant Syncdrive Sport... Scheda tecnica

TLI

TLI VOLspeed Manuale utente

Manuali Accessori per biciclette popolari di altre marche

Sigma

Sigma BC 16.16 Manuale utente

Playcore

Playcore Dero Setbacks Manuale utente

VDO Cyclecomputing

VDO Cyclecomputing x3dw Manuale utente

Cateye

Cateye RAPID X2 Manuale utente

buratti meccanica

buratti meccanica Clorofilla Trail Manuale utente

Shimano

Shimano SG-8R20 Istruzioni operative

BOB

BOB YAK Manuale utente

APLIC

APLIC 303303/20190717TW012 Manuale utente

SRAM

SRAM AXS BlipBox Manuale utente

Garmin

Garmin EDGE 500 Manuale utente

Shimano

Shimano FD-RX810 Manuale utente

Cateye

Cateye V2C - Manuale di istruzioni

KMART

KMART 43115907 Manuale utente

SIGMA SPORT

SIGMA SPORT Buster 2000 Manuale utente

NVO Components

NVO Components STEM Manuale utente

DAXYS

DAXYS BP188 Manuale utente

XLC

XLC BV-W17 Manuale utente

Deda Elementi

Deda Elementi SUPERBOX Manuale utente