TMT BX500 Manuale utente

Software Version:

PS19033F

TMT BX500/800 24V slider motor STEP-BY-STEP instruction manual

Preparation of the Concrete Ground Surface (Base) for Motor Mounting.

Make sure that the ground surface for the motor installation is solid and level with a minimum of

100mm thickness. A good concrete base is paramount to the proper operation of the auto gate

system. The motor mounting plate is 170mm deep x 250mm wide or roughly the size of an A4 page.

If installing cables place these 250mm out from your wall/post and approx. 200mm in from the

corner of the wall/post. Position the motor mounting plate (side nearest the gate) approx. 150-

160mm from the wall/post and approx. 50mm in from your post driveway corner point.

NOTE: You may need to raise the motor to allow the gear rack to fasten properly to your gate

bottom rail. Check this first by placing a gear rack length on top of the sprocket of the motor

alongside the gate and allow for the fastener thickness after installation. Open/close the gate as the

gate may have a bend in it.

55mm

50mm

Motor

Gate

Post

Top View Base Footprint

250mm

170mm

50mm

55mm

Software Version:

PS19033F

Install “Physical Gate Stops”

Physical Gate Stops MUST be installed at each end of your gate. If the Limit Switch on the boxer

motor fails to stop a gate cycle, the Gate Stops will prevent gate falling off the guide rollers and

causing possible injury or damage.

Installing the gear rack to the gate:

For your gate to function smoothly you will need to install the gear rack correctly. The outcome is to

have a 2mm gap between your sprocket and the valley of the gear rack throughout the length of the

gate. Temporarily raise the motor by another 2mm using washer spacers or adjusting the motor

plate height. Remove spacer washers or lower the mounting plate by 2mm once all the gear rack is

installed and secure motor mounting nuts.

NOTE: We recommend you leave extra gear rack over hanging (approx. 100mm) until after you have

mounted the “silver limit cams” and tested the operation of the automation. Only then cut off any

extra with a hacksaw. The gear rack has a steel rod inserted in the nylon casting for strength. Do not

fasten where wheels may be contacted as this will increase gate moving resistance dramatically. If

the fastening screws of the gear rack contact the sprocket cover, it is more than likely due to an

extra-long gate length, bend in the gate or a slight variation in the wheel track alignment. You can

remove the sprocket cover without altering the performance of the opener.

Step 1: Release the auto gate to emergency release by rotating the clutch lever at the front of the

motor so that the gear wheel rotates freely for the alignment and installation of the gear-

rack.

Step 2: Lay all gear rack (on the ground) along the length of the gate. Check end rack supports for

best position of a gear rack lug each side of the sprocket at the fully open/close.

Step 3: Rest the first gear rack on the motor sprocket and ensure that the gear rack is level. Fasten

the gear-rack onto the gate using the fastenings provided.

Step 4: Move the gate 1m or the length of the gear rack and repeat step 3 until all gear-rack have

been installed.

Step 5: Remove the Washer / Spacer from the Motor, and the gap of 2mm between the gear wheel

and the gear rack is automatically achieved.

Step 6: Check to ensure consistent meshing between the gear racks with the gear wheel over the

entire length of the gate. Loosen the screw on the gear-rack to adjust the position of the

gear rack if necessary.

Software Version:

PS19033F

Important Note: Motor Sprocket and Gear Rack life depends almost entirely on their correct

meshing.

Installing “Limit Cams” a must do!

Limit Cams (2 x silver brackets) MUST be installed at each end of your gate Gear Rack. Supplied is a

right (SX) and a left (DX) when installed they are designed to trigger the Limit Switch spring pole to

stop the gate cycle BEFORE contact with physical gate stops.

Removing control board plastic protective cover

Make sure the clutch lever is in the down position. The grey plastic cover that helps protect the

control board from water and insects. Remove using your left hand index finger to pull back and

away the tab in on the left top corner. The cover is semi-hinged on the right side. Be careful not to

dislodge the antenna wire at the bottom.

DESCRIPTION OF THE DEVICE

2mm

gap

Software Version:

PS19033F

PCB Layout

RF-LEARN

DOWN

SET

Software Version:

PS19033F

QUICK SET UP

The board is factory programmed for a standard gate setup with the motor positioned on the left of

the driveway looking at the gate from inside your property. If your motor is on the left of the

driveway you only need to tune your remote and complete “System learning” and it’s all good to go.

If it is on the right then you will need to set up the programme functions below to change motor

direction.

Software Version:

PS19033F

Tuning remotes

Locate the “RF LEARN” button which is the top button on right side of the control board.

Step 1: Press and hold RF LEARN for 3 seconds, the LED will show CS.

Step 2: Press button A on your remote for 2 seconds.

CS signal flashes 3 time on the control board to confirm

the tuning process is completed.

Remove the memories of the remotes

Press and hold down the RF LEARN button for 10 seconds till the LED shows CC.

Pedestrian mode using your remote

Your control board is pre-set to activate the pedestrian mode or partial opening cycle using ONLY

your remote button B. You can adjust the time the gate opens using the LED screen FA function.

To remove the pedestrian function, switch to FH-0 function to turn it OFF.

Using an optional stand-alone receiver.

Use button A (open-stop-close) & B (partial open) for first gate opener, connect the stand alone

receiver to the second gate or garage door and use button C (open-stop-close) on the same remote.

How to use your remote to change Auto Close function:

To turn ON/OFF Auto Close: Long press “D” key for two seconds. The gate will get to fully open

position and all the operation will be locked until long press the “D” key for 2 seconds again to

activate the auto close function again.

Note: Auto close function can ONLY be adjusted when gate is in the fully open or closed position.

You cannot adjust it when the motor is running.

MUST DO: Systems Learning

“Systems learning” will allow the Control board to register your gate factors such as operational

resistance, opening/closing cycle times, speed etc.

NOTE: Gate must be closed!

Warning: Check that both fully open and full closed “limit cams” are in place on the gear rack and

are functioning correctly. Check both fully open and fully closed physical stops are securely in place.

Before starting system learning you must first have a working transmitter. On the control board

press the RF Learn button (TOP BUTTON on the right) once until the blue LED light shines. On your

remote press the top LEFT button once…. Blue light flashes to confirm tuning of remote.

Software Version:

PS19033F

Step 1: The LED display will show –Lmeans the system learning haven’t been completed yet, follow

below steps

Step 2: Simultaneously press the “Set” and the “Down” button (4th BUTTON FROM TOP) for 3

seconds until the LED display shows from –Lto LE

Step 3: You now have less than 10 seconds to press the left top button of your remote to activate

the motor opening cycle and systems learning will be commenced. LED display shows LP to start

system learning process, DO NOT interrupt this operation by press the remote or any other button

on the control panel until the motor finish running

Step4: Once the LED display shows CP means the system learning is completed

Warning: Gate will start moving so keep clear of moving parts.

Step 4: Gate will commence an open cycle until “Open Cam” contacts with “Limit Switch” and stops

the motor. A second or 2 later the gate will start a close cycle until “close cam” contacts “Limit

Switch” and stops the motor. “System-Learning” is now complete.

How to use the LED Screen to set functions of the motor

To adjust the functions such as motor speed, strength of motor, auto close time, you can

programme the system using the LED screen found in the top right of the control board. At stand-by

mode the screen is blank to save energy if the batteries are only operating the board.

There are 2 segments to the screen of which can be controlled by the use of the lower 3 buttons

down the right side UP (2nd from top) SET (3rd from top) and DOWN (bottom). When changing

functions, the first segment is generally a letter and segments 2 is numbers. When the power is first

connected to the board you will see “-L” on the screen for 10 seconds then turns blank which is

standby. To start the programming, you must first decide what function you want to change. Let us

use the auto-closing function 2 as an example.

Step 1: Press and HOLD the SET button for 3 seconds (-L) and release when the screen shows 1 in

segment 1.

Step 2: To change between 1 and 2, press the UP or DOWN button. Once the function 2 is chosen,

then press SET to enter the second layer, to adjust from 20 to 28. IF you want to turn off the

auto-closing function, when LED screen show 20 (No auto-closing) press SET to confirm, then

the LED screen will change back to 2.

Step 3: Wait about 10 seconds or press Button A on the remote (top left one) and the screen will

revert to standby again. Programme completed.

Programme Gate “Opening Direction”

There are 2 locations that you can install your gate motor. Looking at your gate from inside your

property is the motor to be installed on your left or right of the driveway? The LEFT Side (default

setting) 11 is the most popular with the motor sprocket rotating counter-clockwise (looking from the

control board side of the motor at the sprocket) opening the gate from the right to the left.

Software Version:

PS19033F

Right Side install has the motor sprocket rotating clockwise opening the gate from the left to the

right. You will need to change the programme “Opening Direction” to “12”.

NOTE: Gate opener will always do an open cycle when first powered up.

Quick guide to LED screen:

-L

The systems learning process has not been completed.

The system is in its learning mode and awaiting learning instructions.

The system is currently learning a new process.

The system learning process has been completed.

The gate is on opening procedure

The gate is on closing procedure

The gate has stopped

HINTS:

Test the gate opener is working correctly before connecting option devices.

If the gate loads up on your physical stops and stops this will affect the reliability of the gate

operation. Adjust the limit cams so the gate stops BEFORE the safety stopper/ end catcher on

completion of a cycle.

Reduce the speed of medium to heavy gates. Add a deceleration to the program. Increase the amps

to the motor if the gate stops mid-point in a cycle. The dip switches on the right of the panel should

be all to the right which is ON.

You can now connect optional devices by removing the terminal block (pulls off) first and inserting

your wires in the correct location as per the labels. This is so you do not blow the system up

accidently.

Batteries: 2 x 12VDC gel filled batteries are fitted above the motor. When connected in series they

will produce 24VDC. Batteries are connected with a link cable between negative of one battery with

positive of the second battery. The remaining positive and negative are connected to the control

board using the clip on connector. Always check the correct position of the battery connector to the

control board has red to +.

Software Version:

PS19033F

LED Display

Definition

Function

Value

Description

Operation

Direction

Open to LEFT



The function can adjust the

direction of gate opening.



The factory setting is "11".

Open to RIGHT

Auto-Closing

No automatic closing



This function can cause the gate

to close automatically after the

paused time.



The factory setting is "20”



Press and hold “D” key for 2

second can turn of the auto-

closing function. The gate will

be opened and locked, until

next press and hold “D” key

5 seconds

15 seconds

30 seconds

45 seconds

60 seconds

80 seconds

120 seconds

180 seconds

Safety Device

Function Mode

Please refer to page 14, F3 settings



1. The factory setting is “31”.

Opening

Operation Speed

50% operating speed; 50% learning speed



The function can adjust the

running speed of motor.



The factory setting is "44".

70% operating speed; 50% learning speed

85% operating speed; 50% learning speed

100% operating speed; 50% learning speed

Closing

Operation Speed

50% operating speed; 50% learning speed



The function can adjust the

running speed of motor.



The factory setting is "54".

70% operating speed; 50% learning speed

85% operating speed; 50% learning speed

100% operating speed; 50% learning speed

Deceleration

Point

75%



The

default setting is “61”.

80%

85%

90%

95%

Deceleration

Speed

80%



The

default

setting is “73”

60%

40%

25%

Opening

Overcurrent

Setting



The function can adjust the

running force of motor to be

compatible with the gate weight.



The default setting is "85".

WARNING

: The maximum

overcurrent for 500kg motor is 10A, it

may have the potential risk if the

adjustment over 10A current.

10A

11A

12A

13A

Software Version:

PS19033F

Closing

Overcurrent

Setting



The function can adjust the

running force of motor to be

compatible with the gate

weight.



The default setting is "95".

WARNING

: The maximum

overcurrent for 500kg motor is 10A, it

may have the potential risk if the

adjustment over 10A current.

10A

11A

12A

9.1

13A

Pedestrian Mode

Function OFF



The function can adjust the time

of opening partially.



The default setting is "A2".

3 seconds

6 seconds

9 seconds

12 seconds

15 seconds

18 seconds

Flashing Light

The motor and flashing light will operate at

the same time.



If the motor stops by over

current or limit switch, the

flashing light will keep blinking

for 1 minute.



The default setting is “C0”

Followed with FC-0, the flashing light will keep

blinking for1 minute after the motor stop

Followed with FC-0, the flashing light will keep

blinking for 10 minutes after the motor stop

Overcurrent

Reaction

Stop



The default setting is "E3".



The reverse function only

operates 3 times and stops.



If the gate reverses, the auto-

closing function will be

cancelled.

Reverse 1 second and stop

Reverse 3 seconds and stop

Reverse to the end

Main Operation

Key

A Key



The default setting is "F1".

B Key

C Key

D Key

Pedestrian

Function

No function



The default setting is "H2".

A Key

B Key

C Key

D Key

External Device

Key

No function



The default setting is "J3".

A Key

B Key

C Key

D Key

Photocell 1

Activation

Function OFF



The default setting is "L0".

Function ON

Photocell 2

Activation

Function OFF



The default setting is "P0".

Function ON

PCB Stop Terminal

Activation

Function OFF



The default setting is "U0".

Function ON

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Motore popolari di altre marche

Rotax

Rotax 125 senior MAX evo Manuale utente

Kohler

Kohler K361 Manuale utente

MTD

MTD OHV Series Manuale utente

Kohler

Kohler COMMAND CH18-745 Manuale utente

Mercury

Mercury D4.2L D-Tronic Manuale utente

Selve

Selve SE Plus-RC Series Manuale utente

Perkins

Perkins 1206E-E66TA Manuale utente

Skov

Skov DA 174 Manuale

Rossi

Rossi TX11 Series Manuale utente

Siemens

Siemens SIMOTICS T-1FW3 Foglio di istruzioni

AL-KO

AL-KO PRO 350 Manuale utente

MTU

MTU 12 V 4000 Lx4 Manuale utente

Nanni

Nanni N3.30 Manuale di istruzioni

Nanni

Nanni N5.160 CR2 Manuale utente

KSB

KSB SuPreme Series Istruzioni per l'installazione

Hiwin

Hiwin EM1 Series Manuale utente

Rotax

Rotax 912 i series Istruzioni operative

Siemens

Siemens SIMOTICS XP 1MB1 Manuale utente