Tokistar Advantage AVLED-KC Manuale utente

TOKISTAR LIGHTING

1015 E. Discovery Lane

Anaheim, CA 92801

TEL: 714 772 7005 FAX: 714 772 7014

email: info@tokistar.com Website: tokistar.com

Advantage Series

PRECAUTIONS

1. Read all instructions completely before beginning installation.

2. Turn off electricity before beginning installation.

3. All wiring is to be performed by a qualied electrician.

4. Installation must comply with the National Electrical Code, and all applicable codes.

5. Turn main supply to transformer on only after all connections are made and tested.

6. Use only transformers provided by Tokistar with the system.

General Description

Tokistar’s Advantage Series is a 24 VAC lighting system using LED modules or rigid-loop xenon lamps. LEDs are

0.72 watts. Xenon lamps are available at 3 watt and 5 watt. Xenon lamps have the voltage and rating stamped on the

glass at one end. Each Advantage xture is labeled with wattage and operating voltage.

This chart gives recommended

maximum lengths which take into

account these two limitations.

Conforming to these lengths will

ensure no xture exceeds 480

Watts, and will not be subjected to

excessive voltage drop.

Secondary Circuit Limitation

The maximum load of each xture must not exceed 480

Watts (20 amps @ 24 Volts). In addition to this limitation,

consideration must be given to the effects of voltage drop.

Fixtures with lower wattage lamps (such as LEDs) and

more distant socket spacing have recommended maximum

lengths less than 480 Watts.

Secondary Circuit Limitation

Each secondary circuit MUST NOT exceed

20 amps (480 watts @ 24VAC)

TOKISTAR LIGHTING

INSTRUCTION MANUAL

END VIEW

Socket

Wire Wire

Side View

24/5

LED Module

The voltage and lamp rating are stamped

on one end of the xenon lamps.

END VIEW

Wire

Socket

Side View

Wire

END VIEW

Xenon Lamp

Light Source

Description Part No.

0.72 Watt LED

3 Watt Xenon

5 Watt Xenon

AVLED-KC

AVLED-LW

AVLED-WW

AVLED-IW

XB-3F

XB-5F

3 Watt/X3 5 Watt/X5 0.72 Watt LED Modules

Maximum Lamps/Circuit 160 Lamps 96 Lamps 400 LEDs

Lamp Spacing Maximum Run Lengths

2.4" O.C. (60 mm)

3" O.C. (75 mm)

4" O.C. (100 mm)

6" O.C. (150 mm)

32' (9.6 M)

40' (12 M)

48' (14.4 M)

60' (18 M)

19' (5.76 M)

24' (7.2 M)

32' (9.6 M)

48' (14.4 M)

80' (24 M)

100' (30 M)

133' (40 M)

200' (60 M)

Version 1.1

PRECAUTIONS / Heat Consideration

Xenon lamps produce heat and will cause damage if they come in direct contact with persons or combustible

materials. In accordance with NEC/NFPA 70 Article 410.11, combustible materials next to xtures must not be

subjected to temperatures in excess of 90º C (194º F). In order to conform to this standard, xtures need to be

installed according to the minimum space requirements shown below.

Step 1: Mounting Fixtures

Option 1 - Direct Screw Mounting (Part# AV-MS)

Each LED or lamp socket, has four mounting holes designed to accept

screws. For secure mounting, use two screws in opposing holes. Sockets

must be rmly attached to support the weight of the xture.

Option 2A - Channel Clamps (Part# AV-CL)

These clamps are for use with our AV-MC Mounting Channel. Screw the

clamps securely in place, then snap in the channel. Attach clamps every 8".

Option 2 - Mounting Channel (Part# AV-MC)

An optional mounting channel may have been provided with your

materials. Screw the channel securely in place, then snap each socket

into the channel. Attach screws every 8".

End Caps - Part# ECD-WH (White) / Part# ECD-BK (Black)

Ends caps are attached to the end of each Advantage lighting xture. If the

xture needs to be trimmed, a new end cap needs to be attached to the end

of the xture after trimming.

3", 4" and 6" socket spacing

Seamless Light

Advantage xtures are exible enough to turn

corners without the use of special hardware,

eliminating dark spots at corner locations.

2.4" socket spacing

Channel Clamp

Mounting Channel

conforms to a 24" inside

or outside radius.

With Reector 2.4" O.C.

Watts d1 d2 D

.75"

1.25"

1.5"

Basic System 2.4" O.C.

Watts d1 d2 D

1.5"

.75"

1.75"

2.5"

Basic System 2.4" O.C.

Watts d D

1.5"

Basic System 2.4" O.C.

Watts d D

.75"

1.5"

Attach screws

every 8"

End Cap

Advantage Instructions Page 2

Installing Clear Lens - Part# AV-LNS

Your xture may have been provided with clear lens

covers. Push the lens directly over the top of the socket.

When properly seated between the two catches on the side

of the socket, the lens will be securely fastened and not

move from side to side.

WIRE

END VIEW SIDE VIEW

WIRE

FOR SHIELD

Clear Lens

Catches secure

Clear Lens in place.

End View

Step 2: Installing Reectors/LEDs/Lamps

Your xture may have been provided with optional reectors.

Symmetrical reectors (#AVWH/BK-REF-S) must be

attached before lamps are installed. Push the plastic reector

base directly over the socket until it is rmly seated in place.

Asymmetrical reectors (#AVWH/BK-REF-A) may be

attached after lamps or LEDs have been installed.

Silver Reector

Plastic Reector Base

Advantage Socket

Installing Reflectors - Part # AVWH-REF-S (White) / Part #: AVBK-REF-S (Black)

Part# AVWH-REF-A (White) / Part# AVBK-REF-A (Black)

Installing LEDs or Lamps

1. Push LED or Lamp into one

side of socket at an angle.

2. Push other side of LED or Lamp

straight down. Do Not Twist.

SOCKET

WIRE

24/5

LAMP

SOCKET

WIRE

24/5

LAMP

WIRE

Lamp Replacement

1. Remove lamps from socket by pulling directly out (Do Not Twist).

2. Replace lamps only with the same or lower wattage lamp.

Advantage Instructions Page 3

Live conductor must be within connector housing

PRECAUTIONS

When attaching wire to terminals, make certain the insulation is stripped and the connection is made so

no live conductors are exposed.

Step 3: Secondary Wiring

Mini Junction Box Connectors - Part# AV-JBOX

If installation involves running wire through a building structure, conduit may be required to feed the xture. A

miniature junction box is available with a 1/2"Ø knockout for use with conduit ttings. The terminal block inside the

junction box accepts 14-8 AWG wire.

All secondary circuit wiring must conform to the National Electrical Code and all applicable codes.

Terminal Block Connectors - Part# AV-CONN

Advantage Series xtures may have been provided with terminal block connectors. One end of this connector screws

directly to the Advantage xture, and the other end accepts 14-8 AWG wire. A screw hole is provided in the center of

the connector for secure mounting.

AV-CONN Terminal Block

T-Connector

T-Connection System - Part# AV-TCON

Our T-Connection system can feed multiple xtures from a

single wiring harness. Female connectors are attached to the

main harness at any interval and the mating male connectors

attach to each end of the xture.

Screw AV-JBOX

rmly in place

Remove AV-JBOX Cover

AV-CONN inside AV-JBOX

Install

Strain-Relief

Maximum 480 Watts (20 Amps) per connection

Advantage Instructions Page 4

PRECAUTIONS

Transformers should be installed in an accessible location. Magnetic transformers generate heat and must be

installed in locations where there is free-air circulation. Electronic transformers require less space to dissipate

heat, but they too should be installed in accessible locations with free-air circulation.

For additional information, please refer to the instruction manual provided with your transformer.

Secondary Circuit Protection

Transformers are provided with circuit breakers to protect secondary circuits. The maximum size circuit breaker on a

transformer is 25 amps, but the circuit wired to the breaker MUST NOT EXCEED 20 AMPS.

There are several transformer sizes available, and different size breakers installed in them. Below is a selection of trans-

formers with their respective circuit limitations.

Larger capacity transformers with multiple out-

puts can be centrally located and feed xtures

in either direction.

Input Voltage

Transformer

Do not exceed maximum xture length

Do not exceed transformer output rating

Transformer Location

The maximum recommended distance between the xture and the transformer varies, based upon the load of each x-

ture and the size of secondary wire feeding the xture. It is impossible to give a denitive distance without considering

all the variables. Electrical engineers and contractors can calculate these distances. Should you need guidance, consult

the factory.

Step 4: Transformer Instructions

25 A

500 Watt

Transformer

Max. Load 20 Amps

480 Watts Max.

15 A

300 Watt

Transformer

Max. Load 12.5 Amps

300 Watts @ 24 VAC

250 Watt

Transformer 15 A Max. Load 10.4 Amps

250 Watts @ 24 VAC

7 A

100 Watt

Transformer

Max. Load 4.1 Amps

100 Watts @ 24 VAC

25 A

1000 Watt

Transformer Max. Load 20 Amps

480 Watts @ 24 VAC

Max. Load 20 Amps

480 Watts @ 24 VAC 960 Watts Max.

25 A

750 Watt

Transformer Max. Load 20 Amps

480 Watts @ 24 VAC

Max. Load 20 Amps

480 Watts @ 24 VAC 750 Watts Max.

Advantage Instructions Page 5

Version 1.1

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Luce da lavoro popolari di altre marche

ANSMANN

ANSMANN POWERLIGHT 5.1 Manuale utente

RTRMAX

RTRMAX RTX1868 Manuale utente

FeinTech

FeinTech LAL00220 Manuale utente

Bunker Hill Security

Bunker Hill Security 64735 Manuale utente

Goobay

Goobay 30450 Manuale utente

REV Ritter

REV Ritter SPOT Manuale utente

Ignition

Ignition Stagepix Line 100 IP Manuale utente

SCANGRIP

SCANGRIP DUO CONNECT Manuale utente

Bosch

Bosch GLI 18 V Manuale utente

Bayco

Bayco SL-1514 Manuale utente

EUFAB

EUFAB SMD LED 8+1 Manuale utente

DeWalt

DeWalt DCL510 Manuale utente

PowerSmith

PowerSmith PWLD080T Manuale utente

MaxLite

MaxLite 73683 Manuale utente

Heitronic

Heitronic Trend 27867 Manuale utente

Monzana

Monzana Gore MZCL10 Manuale utente

EINHELL

EINHELL TE-CL 18/2000 LiAC Manuale utente

Bayco

Bayco NIGHTSTICK Dual-Light Xtreme Lumens... Manuale utente