Toro 08860 Manuale utente
1
All Rights Reserved
Printed in the USA
W2008 by The Toro Company
8111 Lyndale Avenue South
Bloomington, MN 55420-1196
Discharge Chute Kit
For Sand Pro, Grounds Pro and Groundsmaster Debris
Blowers
Model No. 08860
Form No. 3324–993 Rev. A
Installation Instructions
Note: If front discharge is desired, an optional Chute,
Toro Part No. 104–0329–01, is available.
1. Remove screws and washers securing deflector to
blower discharge opening (Fig. 1). Remove deflector
and retain for future installation.
Sand Pro Debris Blower Shown
1
2
Figure 1
1. Discharge opening
deflector
2. Deflector mounting screws
2. Mount pivot assembly to top of chute assembly with
(5) 3/8116 x 7/8” lg. carriage bolts, .406 x .813 flat
washers and 3/8–16 locknuts (Fig. 2).
Note: Chute assembly can be rotated 180 degrees for right
or left discharge on debris blower.
1
2
Figure 2
1. Pivot assembly 2. Chute assembly
3. Using (2) 3/8–16 x 7/8” carriage bolts, .406 x .813 flat
washers and 3/8–16 locknuts, mount a cover plate and
spring mount bracket to slot in front of blower
discharge chute (Fig. 3).
4. Using (2) 3/8–16 x 7/8” carriage bolts, .406 x .813 flat
washers and 3/8–16 locknuts, mount a cover plate to
slot in rear of blower discharge chute (Fig. 3).
12
Back
1
Front
Figure 3
1. Cover plate 2. Spring mount bracket
5. Mount a eye bolt to side of chute assembly with (2)
washers and jam nuts. Position eye bolt as shown in
(Fig. 4).
1
Figure 4
1. Eye bolt
6. Mount the deflector to chute assembly with screws and
washers previously removed (Fig. 5).
2
1
Figure 5
1. Deflector
7. Mount chute assembly to discharge opening with a
pivot rod, (2) flat washers and cotter pins. Position
components as shown in figure 6.
1
Figure 6
1. Pivot rod
8. Hook spring onto eye bolt and spring mount bracket
(Fig. 3 & 4).
9. Measure, mark and cut off handle tube to required
length for specific blower application.
Amount to cut off handle tube:
SandPro – 20 to 24 inches
Groundsmaster 200 Blower – 10 to 12 inches
Groundsmaster 300 Blower – 10 to 12 inches
GroundsPro 2000 Blower – None
Cut to length
1
Figure 7
1. Handle
10. Slide handle tube into handle support and loosely
secure with (2) U–bolts, washers and nut (Fig. 8).
1
2
Figure 8
1. Handle tube 2. Handle support
11. Mount handle assembly to blower mounting tabs with
a washer and cotter pin (Fig. 9).
1
2
Figure 9
1. Handle assembly 2. Linkage rod
12. Mount linkage rod to handle assembly with a washer
and cotter pin (Fig. 9).
13. Mount linkage rod to deflector assembly with a washer
and cotter pin (Fig. 10).
1
Figure 10
1. Linkage rod
Altri manuali Toro Soffiatore
Toro
Toro Flex-Force Power System 51820T Manuale utente
Toro
Toro 51557 Manuale utente
Toro
Toro 51821 Manuale utente
Toro
Toro 319000001 Manuale utente
Toro
Toro Flex-Force Power System 51822 Manuale utente
Toro
Toro Pro Force 44554 Manuale utente
Toro
Toro ProForce 44538 Manuale utente
Toro
Toro Air Rake 51551 Manuale utente
Toro
Toro 51581 Manuale utente
Toro
Toro PowerPlex 40V MAX Manuale utente
Toro
Toro 51593 Manuale utente
Toro
Toro 3200 Manuale utente
Toro
Toro Versa Vac Manuale utente
Toro
Toro Pro Force Manuale utente
Toro
Toro 51576 Manuale utente
Toro
Toro 51549-79000001 Manuale utente
Toro
Toro 51619 Manuale utente
Toro
Toro Air Rake Manuale utente
Toro
Toro Power Sweep 51586 Manuale utente
Toro
Toro 51702A Manuale utente
