Toro Flex-Force Power System 51833T Manuale utente
Form No. 3461-1 15 Rev A
Flex-Force Power System™ 60V Stick Edger
51833 , 51833T
Cortabordes Flex-Force Power System™ 60 V
51833 , 51833T
Coupe-bordures à manche Flex-Force Power
System™ de 60 V
51833 , 51833T
www .T oro.com.
*3461-115*
Form No. 3461-1 12 Rev A
Flex-Force Power System
™
60V
Stick Edger
Model No. 51833 —Serial No. 323000001 and Up
Model No. 51833T —Serial No. 323000001 and Up
Register at www .T oro.com.
Original Instructions (EN)
*3461-112*
For assistance, please see
www .T oro.com/support
for instructional videos
or contact 1-888-384-9939
before returning this
product.
W ARNING
CALIFORNIA
Proposition 65 W arning
The power cord on this product contains
lead, a chemical known to the State
of California to cause birth defects
or other reproductive harm. W ash
hands after handling.
Use of this product may cause exposure
to chemicals known to the State of
California to cause cancer , birth defects,
or other reproductive harm.
Introduction
This edger is intended to be used by residential
homeowners to trim grass around the edge of
driveways, sidewalks, and more as needed outdoors.
It is designed to use T oro 60V lithium-ion battery
packs. These battery packs are designed to be
charged only by T oro 60V lithium-ion battery chargers.
Using this product for purposes other than its intended
use could prove dangerous to you and bystanders.
Model 51833T does not include a battery or a
charger .
Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. Y ou are responsible for
operating the product properly and safely .
V isit www .T oro.com for product safety and operation
training materials, accessory information, help nding
a dealer , or to register your product.
Whenever you need service, genuine the
manufacturer parts, or additional information, contact
an Authorized Service Dealer or the manufacturer
Customer Service and have the model and serial
numbers of your product ready . Figure 1 identies
the location of the model and serial numbers on the
product. W rite the numbers in the space provided.
Important: W ith your mobile device, you can
scan the QR code on the serial number decal (if
equipped) to access warranty , parts, and other
product information.
g428616
Figure 1
1. Model and serial number location
Model No.
Serial No.
© 2023—The T oro® Company
81 1 1 L yndale A venue South
Bloomington, MN 55420
2
Contact us at www .T oro.com.
Printed in China
All Rights Reserved
Safety-Alert Symbol
The safety-alert symbol ( Figure 2 ) shown in this
manual and on the machine identies important safety
messages that you must follow to prevent accidents.
g000502
Figure 2
Safety-alert symbol
The safety-alert symbol appears above information
that alerts you to unsafe actions or situations and
is followed by the word DANGER ,W ARNING , or
CAUTION .
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious
injury .
W ARNING indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury .
CAUTION indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury .
This manual uses two other words to highlight
information. Important calls attention to special
mechanical information and Note emphasizes general
information worthy of special attention.
Safety
IMPORT ANT SAFETY
INSTRUCTIONS
W ARNING
When using electric gardening tools, always
read and follow basic safety warnings and
instructions to reduce the risk of re, electric
shock, and personal injury , including the
following:
Read All Instructions
I. T raining
1. The operator of the tool is responsible for any
accidents or hazards occurring to others or their
property .
2. Do not allow children to use or play with the
tool, battery pack, or the battery charger; local
regulations may restrict the age of the operator .
3. Do not allow children or untrained people to
operate or service this device. Allow only people
who are responsible, trained, familiar with the
instructions, and physically capable to operate
or service the device.
4. Before using the tool, battery pack, and battery
charger , read all the instructions and cautionary
markings on these products.
5. Become familiar with the controls and proper use
of the tool, battery pack, and battery charger .
II. Preparation
1. Keep bystanders and children away from the
operating area.
2. Use only the battery pack specied by T oro.
Using other accessories and attachments may
increase the risk of injury and re.
3. Plugging the battery charger into an outlet that is
not 120 V can cause a re or electric shock. Do
not plug the battery charger into an outlet other
than 120 V . For a dif ferent style of connection,
use an attachment plug adapter of the proper
conguration for the power outlet if needed.
4. Do not use a damaged or modied battery
pack or battery charger , which may exhibit
unpredictable behavior that results in re,
explosion, or risk of injury .
5. If the supply cord to the battery charger is
damaged, contact an Authorized Service Dealer
to replace it.
6. Charge the battery pack with only the battery
charger specied by T oro. A charger suitable for
3
1 type of battery pack may create a risk of re
when used with another battery pack.
7. Charge the battery pack in a well-ventilated area
only .
8. Follow all charging instructions and do
not charge the battery pack outside of the
temperature range specied in the instructions.
Otherwise, you may damage the battery pack
and increase the risk of re.
9. Do not operate the tool without all guards and
other safety protective devices in place and
functioning properly on the tool.
10. Dress properly—W ear appropriate clothing,
including eye protection; long pants; substantial,
slip-resistant footwear; rubber gloves; and
hearing protection. T ie back long hair and do
not wear loose clothing or loose jewelry that can
get caught in moving parts. W ear a dust mask in
dusty operating conditions.
III. Operation
1. A void dangerous environments—Do not use the
tool in rain or in damp or wet locations.
2. Use the proper tool for your application—Using
the tool for purposes other an its intended use
could prove dangerous to you and bystanders.
3. Prevent unintentional starting—Ensure that the
switch is in the O FF position before connecting
to the battery pack and handling the tool. Do
not carry the tool with your nger on the switch
or energize the tool with the switch in the O N
position.
4. Operate the tool only in daylight or good articial
light.
5. If the tool strikes an object or starts to vibrate,
immediately shut of f the tool, wait for all moving
parts to stop, and disconnect the battery before
examining the tool for damage. Make all
necessary repairs before resuming operation
6. Remove the battery pack from the tool before
adjusting it or changing accessories.
7. Keep your hands and feet away from the cutting
area and all moving parts.
8. Shut of f the tool, remove the battery pack from
the tool, and wait for all movement to stop before
adjusting, servicing, cleaning, or storing the tool.
9. Remove the battery pack from the tool whenever
you leave it unattended.
10. Do not force the tool—Allow the tool to do the
job better and safer at the rate for which it was
designed.
1 1. Do not overreach—Keep proper footing and
balance at all times, especially on slopes. W alk,
never run with the tool.
12. Stay alert—W atch what you are doing and use
common sense when operating the tool. Do not
use the tool while ill, tired, or under the inuence
of alcohol or drugs.
13. Ensure that the ventilation openings are kept
clear of debris.
14. Under abusive conditions, the battery pack may
eject liquid; avoid contact. If you accidently
come into contact with the liquid, ush with
water . If the liquid contacts your eyes, seek
medical help. Liquid ejected from the battery
pack may cause irritation or burns.
15. Do not expose a battery pack or tool to re or
excessive temperature. Exposure to re or
temperature above 130°C (265°F) may cause
explosion.
16. CAUTION—A mistreated battery pack may
present a risk of re, explosion, or chemical
burn.
•Do not disassemble the battery pack.
•Replace the battery pack with a genuine
T oro battery pack only; using another type of
battery pack may cause a re or risk of injury .
•Keep battery packs out of the reach of
children and in the original packaging until
you are ready to use them.
IV . Maintenance and Storage
1. Maintain the tool with care—Keep it clean and
in good repair for best performance and to
reduce the risk of injury . Follow the instructions
for lubricating and changing accessories. Keep
handles dry , clean, and free from oil and grease.
2. When the battery pack is not in use, keep it
away from metal objects such as paper clips,
coins, keys, nails, and screws that can make a
connection from 1 terminal to another . Shorting
the battery terminals may cause burns or a re.
3. Keep your hands and feet away from moving
parts.
4. Shut of f the tool, remove the battery pack from
the tool, and wait for all movement to stop before
adjusting, servicing, cleaning, or storing the tool.
5. Check the tool for damaged parts—If there
are damaged guards or other parts, determine
whether it will operate properly . Check for
misaligned and binding moving parts, broken
parts, mounting, and any other condition that
may af fect its operation. Unless indicated in the
instructions, have an Authorized Service Dealer
repair or replace a damaged guard or part.
6. If the blade becomes worn, bent, or damaged,
replace it; contact an authorized T oro distributor .
4
7. Do not attempt to service or repair the tool,
battery pack, or battery charger except as
indicated in the instructions. Have an Authorized
Service Dealer perform service using identical
replacement parts to ensure that the product is
safely maintained.
8. Store an idle tool indoors in a place that is dry ,
secure, and out of the reach of children.
9. Do not dispose of the battery in a re. The
cell may explode. Check with local codes for
possible special disposal instructions.
SA VE THESE
INSTRUCTIONS
5
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger . Replace any decal that is damaged or missing.
decal144-3098
144-3098
decal144-3096
144-3096
decal144-3094
144-3094
1. The battery pack is
charging.
3. The battery pack is over
or under the appropriate
temperature range.
2. The battery pack is fully
charged.
4. Battery pack charging fault
decal140-8475
140-8475
1. Read the Operator ’ s
Manual .
3. Keep away from open re
or ames.
2. Call2Recycle® battery
recycling program
4. Do not expose to rain.
6
decal137-9461
137-9461
1. Battery charge status
decal139-5210
139-5210
1. W arning—read the Operator ’ s Manual ; stay away from
moving parts; keep all guards in place; wear eye protection;
do not operate in wet conditions.
decal139-5346
139-5346
7
Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure Description
Qty .
Use
1
Allen wrench 1
Unfold the handle.
Auxiliary handle assembly 12
Edger adjustment tool 1
Install the auxiliary handle.
Important: The battery pack is not fully charged when you purchase it. Before using the tool for the
rst time, refer to Charging the Battery Pack ( page 14 ) .
1
Unfolding the Handle
Parts needed for this procedure:
1 Allen wrench
Procedure
1. Unfold the handle (A of Figure 3 ).
2. Align the locking button on the lower shaft with the slotted hole on the upper shaft and slide the 2 shafts
together (B and C of Figure 3 ).
Note: The locking button clicks into the slotted hole when the shafts are secured (D of Figure 3 ).
3. Using the provided Allen wrench, tighten the screw on the shaft connector until it is secure (E of Figure 3 ).
8
Altri manuali per Flex-Force Power System 51833T
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Lingue:
Altri manuali Toro Bordatore
