Toro 145-3530 Manuale utente

Form No. 3463-130 Rev A

T rimmer Rack

GrandStand

Revolution

Mower

Model No. 145-3530

Installation Instructions

Installation

Loose Parts

Use the chart below to verify that all parts have been shipped.

Procedure Description

Qty .

Use

No parts required

–

Prepare the machine for installation.

Upper mount bracket 1

Screw (5/16 inch)

Slot bracket

Carriage bolt (1/4 x 3/4 inch)

Nut (1/4 inch)

Large st clamp

Large backer plate 1

Hex-head ange screw (1/4 x 1-1/2

inches)

Install the upper bracket assembly .

Lower mount bracket 1

Screw (5/16 inch)

Adjustment plate 1

Carriage bolt (1/4 x 3/4 inch)

Nut (1/4 inch)

Small st clamp

Small backer plate

Hex-head ange screw (1/4 x 1-1/2

inches)

Install the lower mount bracket.

No parts required

–

Complete the installation.

81 1 1 L yndale A venue South

Bloomington, MN 55420

Original Instructions (EN)

Printed in the USA

*3463-130*

Preparing the Machine

No Parts Required

Procedure

1. Park the machine on a level surface.

2. Disengage the drives and the power take-of f.

3. Shut of f the machine and remove the key .

4. W ait for all moving parts to stop.

5. T urn the battery-disconnect switch to the O FF

position.

6. Lower the platform.

7. Loosen the twist knobs on each side of the

machine.

g375719

Figure 1

1. T wist knob

2. Cushion

8. Lower the cushion to the platform.

9. Remove the rear access cover .

g377627

Figure 2

Installing the Upper Bracket

Assembly

Parts needed for this procedure:

1 Upper mount bracket

Screw (5/16 inch)

Slot bracket

Carriage bolt (1/4 x 3/4 inch)

Nut (1/4 inch)

Large st clamp

1 Large backer plate

Hex-head ange screw (1/4 x 1-1/2 inches)

Procedure

1. On the left side of the machine, measure and

mark the 3 holes as shown below .

g443616

Figure 3

1. 17.6 cm (6.93 inches) 4. 6.4 cm (2.52 inches)

2. 4.6 cm (1.82 inches) 5. 1 1.4 cm (4.5 inches)

3. 4.1 cm (1.61 inches) 6. 14.5 cm (5.71 inches)

W ARNING

Using a drill without proper eye

protection may allow debris to enter the

eye, causing injury .

When drilling, always wear eye

protection.

2. Use a drill bit (9/32 inch) to drill through the 3

marked hole locations.

Note: When drilling, avoid pushing the drill bit

too far beyond the plate.

3. Use compressed air to remove the metal

shavings from drilling.

4. Use 3 screws (5/16 inch) to secure the upper

mount bracket to the machine.

g441540

Figure 4

1. Screw (5/16 inch)

2. Upper mount bracket

5. Use 2 carriage bolts (1/4 x 3/4 inch) and 2 nuts

(1/4 inch) to secure the slot bracket to the upper

mount bracket.

g441543

Figure 5

1. Slot bracket 3. Nut (1/4 inch)

2. Carriage bolt (1/4 x 3/4

inch)

4. Upper mount bracket

6. Use 2 hex-head ange screws (1/4 x 1-1/2

inches) and 2 nuts (1/4 inch) to secure the large

st clamp and large backer plate to the slot

bracket.

g441545

Figure 6

1. Large st clamp 3. Nut (1/4 inch)

2. Large backer plate

4. Hex-head ange screw

(1/4 x 1-1/2 inches)

Installing the Lower Mount

Bracket

Parts needed for this procedure:

1 Lower mount bracket

Screw (5/16 inch)

1 Adjustment plate

Carriage bolt (1/4 x 3/4 inch)

Nut (1/4 inch)

Small st clamp

Small backer plate

Hex-head ange screw (1/4 x 1-1/2 inches)

Procedure

1. Using the lower mount bracket as a template,

mark the 2 holes as shown below .

g443617

Figure 7

1. 2.54 cm (1 inch) 3. 17.6 cm (6.93 inches)

2. 2.54 cm (1 inch)

W ARNING

Using a drill without proper eye

protection may allow debris to enter the

eye, causing injury .

When drilling, always wear eye

protection.

2. Use a 9/32 inch drill bit to drill through the 2

marked hole locations.

Note: Do not push the drill bit too far past the

plate when drilling.

3. Use 2 screws (5/16 inch) to secure the lower

mount bracket to the machine.

g441547

Figure 8

1. Lower mount bracket

2. Screw (5/16 inch)

4. Use compressed air to remove the metal

shavings from drilling.

5. Use 2 carriage bolts (1/4 x 3/4 inch) and 2 nuts

(1/4 inch) to secure the adjustment plate to the

lower mount bracket.

g441563

Figure 9

1. Lower mount bracket 3. Adjustment plate

2. Carriage bolt (1/4 x 3/4

inch)

4. Nut (1/4 inch)

6. Use 2 hex-head ange screws (1/4 x 1-1/2

inches) and 2 nuts (1/4 inch) to secure the

small backer plate and small st clamp to the

adjustment plate.

g441614

Figure 10

1. Small st clamp 3. Nut (1/4 inch)

2. Small backer plate 4. Hex-head ange screw

(1/4 x 1-1/2 inches)

Completing the Installation

No Parts Required

Procedure

1. Install the rear access cover .

g377627

Figure 1 1

2. Raise the cushion to the platform.

3. T ighten the twist knobs on each side of the

machine.

g375719

Figure 12

1. T wist knob

2. Cushion

4. Adjust the upper and lower plates to t your

trimmer as needed.

5. T urn the battery-disconnect switch to the O N

position.

Figure 13 illustrates the correct position of the

trimmer on the rack.

Note: Position the upper trimmer handle so that

is held in place by the upper clamp.

g442743

Figure 13

Notes:

Indice

Altri manuali Toro Accessori per tosaerba

Manuali Accessori per tosaerba popolari di altre marche

Ariens

Ariens 891008 Manuale utente

Rover

Rover 108 - 109 Manuale utente

Snapper

Snapper 1690047 Manuale utente

Scag Power Equipment

Scag Power Equipment GC-F4 Manuale utente

RHINO

RHINO 800 Manuale utente

Exmark

Exmark Quest 126-7506 Manuale utente

Snapper

Snapper 1685167 Manuale utente

Cub Cadet

Cub Cadet 19B70029100 Manuale utente

Stihl

Stihl AMK 043.1 Manuale utente

MTD

MTD 753-0873 Manuale

Bush Hog

Bush Hog RG60 Manuale utente

Land Pride

Land Pride RCF2760 Manuale utente

Simplicity

Simplicity 211 Manuale utente

Exmark

Exmark ULTRAVAC QUICK DUMP SYSTEM Manuale utente

Excel

Excel Two Bag Catcher Manuale utente

Textron

Textron Jacobsen Pro12 DFS Manuale utente

Ryobi

Ryobi AC018130 Manuale utente

Snapper

Snapper 4544 Guida all'installazione