Toro TouchNet 89-9150 Manuale utente

Introduction

The Interface Cable Kit includes a special serial cable and a HayesTM AccuraTM 336 Fax Modem and power supply.

Installation of the modem with the TouchNet central enables system communication via telephone line with compatibly-

equipped Network LTC Plus satellite controllers.

Note: While not a requirement for operation, a dedicated telephone line is recommended for this application.

Procedure

1. Place the On/Off switch of the TouchNet Central and data/fax modem in the Off position.

2. Connect the TouchNet to the modem using the interface serial cable supplied as shown in Figure 1.

3. Referring to Figure 1 and the instructions provided with the Hayes modem, install the remaining connections as shown.

Note: Setup software included with the modem is not required for installation or operation with the TouchNet Central.

System Set Up and Test

1. Switch on the TouchNet Central and modem

2. Ensure COMMERCIAL mode is selected in the System Type

screen.

Note: The telephone communications option is not enabled

when the Golf system type is selected.

3. Ensure the modem-equipped Network LTC Plus satellite is

operational.

3. On the TouchNet Central, select SATELLITES from the Menu

screen.

4. Scroll to the address number of the telephone modem-

equipped satellite.

Note: Ensure the satellite is enabled for operation (represented by an “X” in the box adjacent to the satellite number). If

an “X” is not displayed, simply touch the box area to enable the satellite.

5. Select telephone communications for the satellite by touching the TELEPH box. A telephone number string (zeros) will

appear. See Figure 2.

6. Touch the telephone number string. A pop-up keypad will appear enabling the satellite modem telephone number to be

entered.

7. After entering the telephone number (a minimum of seven digits), return to the Menu screen and select UTILITIES.

8. On the utilities screen, touch “TELEPHONE”under Communications Setup. The Telephone setup screen will be dis-

played with the default setup parameters. You may find it necessary to change the default settings for your application.

Note: The default settings should be sufficient for most applications. For additional information regarding telephone

setup parameters, refer to telephone communications setup within the “Special Features”section of the TouchNet for

LTC Plus User’s Guide.

TouchNetTM Central for Network LTCTM Plus

Telephone Modem Kit, Model No. 89-9150

Installation Instructions

TouchNet Central

(Back View)

Hayes Modem

On/Off

Switch

On/Off

Switch

Interface Cable

P/N 363-3612

Telephone Line

To Telephone

(Optional)

To Modem

Power Supply

Figure 1

Figure 2

Touch screen here to

enter satellite modem

telephone number.

9. To test Telephone communications operation, perform the following system checks:

•Verify that the satellite is operational.

•Verify that the satellite is appropriately designated for telephone communications in the TouchNet Satellite

screen.

•From the Menu screen, select the SAT MONITOR screen. The TouchNet will automatically initiate communica-

tions with the field satellites.

Note: Connect time may require up to one minute when establishing communications between the TouchNet

central and the satellite.

•From the Satellite Monitor screen, select the telephone modem-equipped satellite address number, then select

the CHECK 1 screen. Satellite Status information will be displayed within 10 to 25 seconds.

•If a communication error occurs, refer to the troubleshooting information below for possible solutions.

Printing Date

March 1998 Rev. A Form Number

371-0048

Irrigation Division

An ISO 9001-Certified Facility

P.O. Box 489 Riverside, CA 92504

Troubleshooting The Telephone-Link System

Problem

“No Response”

“No Dial Tone”

“Telephone Busy”

“No Answer”

“No Carrier”

Solution

Verify the following:

•The central modem connections are correct, its power

supply is plugged in and the On/Off switch is in the ON

position.

•The telephone line is functioning properly.

•The telephone modem-equipped satellite is operating

properly and its telephone modem is On.

Note: If a satellite-related problem has been confirmed

and corrected, reset the system by switching the central

and satellite modems Off and On.

The modem has not sensed a dial tone on the tele-

phone line. Verify that the telephone line is properly

connected and functional.

The central modem has sensed the satellite modem is

busy. The TouchNet will automatically redial three times.

If necessary, increase the redial value on the Telephone

Set Up screen.

The modem has sensed the satellite modem is not

answering. Verify that the satellite telephone modem

connections are correct, power is on and the phone line

is functional.

The central and satellite modems have connected but

cannot communicate due to an improper or non-exis-

tent carrier signal. Reset the system by switching the

central and satellite modems Off and On. Verify that the

telephone line is functional.

Indice

Altri manuali Toro Modem

Toro

Toro 118-6161SK Manuale utente

Manuali Modem popolari di altre marche

Davicom

Davicom DM562AP Manuale utente

EpiValley

EpiValley TATA indicom SXC-1080 Manuale utente

Zte

Zte WiMAX Manuale utente

Intelimax

Intelimax MA-2060 Manuale utente

SMC Networks

SMC Networks D3CM1604V Manuale per l'uso e la cura

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manuale utente

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manuale utente

Samsung

Samsung AceLink SAM-335A Manuale utente

Enfora

Enfora Enabler-G Guida rapida alla configurazione

iRZ

iRZ ATM2-232 Manuale utente

Zhone

Zhone 6310 Manuale utente

Paradyne

Paradyne Hotwire 7976 Manuale utente

US Robotics

US Robotics 3453C Manuale utente

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manuale utente

Zte

Zte MF823 Manuale utente

Four-Faith

Four-Faith F1403 Manuale utente

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manuale utente

Gemtek

Gemtek WiMAX WIXFBR-103 Manuale utente