Toshiba D-R1SU Manuale utente
DVD VIDEO RECORDER
SERVICE MANUAL
FILE NO. 810-200334
D-R1SU
D-R1SC
DIGITAL VIDEO
DOCUMENT CREATED IN JAPAN, Oct., 2003
LASER BEAM CAUTION LABEL
When the power supply is being turned on, you may not remove this laser beam caution label. If it removes, radiation of a
laser may be received.
PREPARATION OF SERVICING
Pickup Head consists of a laser diode that is very susceptible to external static electricity.
Although it operates properly after replacement, if it was subject to electrostatic discharge during replacement,
its life might be shortened. When replacing, use a conductive mat, soldering iron with ground wire, etc. to
protect the laser diode from damage by static electricity.
And also, the SI and IC are same as above.
1M
W
Ground conductive
wrist strap for body.
Soldering iron
with ground wire
or ceramic type
Conductive mat The ground resistance
between the ground line
and the ground is less than 10
W
.
SAFETY NOTICE
SAFETY PRECAUTIONS
LEAKAGE CURRENT CHECK
Plug the AC line cord directly into a 120V AC outlet (do
not use an isolation transformer for this check). Use an
AC voltmeter, having 5000 Ωper volt or more sensitivity.
Connect a 1500 Ω10 W resistor, paralleled by a 0.15 µF
150V AC capacitor between a known good earth ground
(water pipe, conduit, etc.) and all exposed metal parts of
cabinet (antennas, handle bracket, metal cabinet
screwheads, metal overlays, control shafts, etc.).
Measure the AC voltage across the 1500 Ωresistor.
The test must be conducted with the AC switch on and
then repeated with the AC switch off. The AC voltage
indicated by the meter may not exceed 0.3 V. A reading
exceeding 0.3 V indicates that a dangerous potential
exists, the fault must be located and corrected.
Repeat the above test with the DVD VIDEO RECORDER
power plug reversed.
NEVER RETURN A DVD VIDEO RECORDER TO THE
CUSTOMER WITHOUT TAKING NECESSARY
CORRECTIVE ACTION.
READING SHOULD NOT EXCEED 0.3V
DVD VIDEO RECORDER
AC OUTLET
AC VOLTMETER
(5000 Ωper volt
or more sensitivity)
Good earth ground
such as a water pipe,
conduit, etc.
Test all exposed metal.
Voltmeter Hook-up for Leakage Current Check
0.15 µF 150V AC
1500 Ω
10 W
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
SECTION 2
PART REPLACEMENT AND ADJUSTMENT PROCEDURES
SECTION 3
SERVICING DIAGRAMS
1. CIRCUIT SYMBOLS AND
SUPPLEMENTARY EXPLANATION
1-1. Circuit Symbols
1-2. Precautions for Part Replacement
2. PRINTED WIRING BOARD AND
SCHEMATIC DIAGRAM
3. BLOCK DIAGRAMS
3-1. Overall Block Diagram
4. CIRCUIT DIAGRAMS
4-1. Power Supply Circuit Diagram
4-2. Front Circuit Diagram
4-2-1. Front (Jack) Circuit Diagram
4-2-2. Front (L) Circuit Diagram
4-2-3. Front (R) Circuit Diagram
4-3. Digital Circuit Diagram
4-3-1. Digital 1 Circuit Diagram
4-3-2. Digital 2 Circuit Diagram
4-4. Mother Circuit Diagram
4-4-1. Tuner Circuit Diagram
4-4-2. Timer Circuit Diagram
4-4-3. Audio Circuit Diagram
4-4-4. Video Circuit Diagram
5. PC BOARDS
5-1. Front (L) PC Board
5-2. Front (R) PC Board
5-3. Front (Jack) PC Board
5-4. Digital PC Board
5-5. Mother PC Board
CONTENTS
SECTION 1
GENERAL DESCRIPTIONS
1. OPERATING INSTRUCTIONS
1. REPLACEMENT OF MECHANICAL PARTS
1-1. Cabinet Replacement
1-1-1. Top Cover
1-1-2. Front Panel
1-1-3. Tray Door
1-1-4. RAM Drive
1-1-5. Fan
1-1-6. Rear Panel
1-2. PC Board Replacement
1-2-1. Digital PC Board
1-2-2. Mother PC Board
1-2-3. Power PC Board
1-2-4. Front (R), Front (L) and Jack PC Board
2. LOCATION OF MAIN PARTS
2-1. Location of Main Parts
2-2. Location of PC Boards
SECTION 4
PARTS LIST
SAFETY PRECAUTION
NOTICE
ABBREVIATIONS
1. Integrated Circuit (IC)
2. Capacitor (Cap)
3. Resistor (Res)
4. EXPLODED VIEWS
4-1. Packing Assembly
4-2. Chassis Assembly
5. PARTS LIST
SECTION 1
GENERAL DESCRIPTIONS
1. OPERATING INSTRUCTIONS
Please refer to the owner's manual about the contents.
SECTION 1
GENERAL DESCRIPTIONS
2. LOCATION OF MAIN PARTS
2-1. Location of Main Parts
Fig. 1-2-1
2-2. Location of PC Boards
Fig. 1-2-2
ZG45 FAN
RAM1 RAM DRIVE
EU05 Mother PC board
EU01 Digital PC board
EU02 Power PC board
EU03A Front (R) PC board
EU03B Front (L) PC board
EU55 Jack PC board
SECTION 2
PART REPLACEMENT AND
ADJUSTMENT PROCEDURES
SECTION 2
PART REPLACEMENT AND
ADJUSTMENT PROCEDURES
CAUTIONS BEFORE STARTING PART REPLACEMENT
Electronic parts are susceptible to static electricity and may be easily damaged, so do not forget to ground as required.
Many screws are used inside the unit. To prevent the screws from missing or dropping, etc. always use a magnetized
screwdriver in servicing. Several kinds of screws are used and some of them need special cautions. That is, take care of
the tapping screws securing molded parts and fine pitch screws used to secure metal parts. If they are used improperly,
the screw holes will be easily damaged and the parts can not be fixed.
1. REPLACEMENT OF MECHANICAL PARTS
1-1. Cabinet Replacement
1-1-1. Top Cover
(1) Remove seven screws (1), and then remove the top cover (2).
Fig. 2-1-1
Screws (1)
Screws (1)
Screws (1)
Top cover (2)
1-1-2. Front Panel
(1) Remove the top cover. (Refer to item 1-1-1.)
(2) Disconnect the flexible cable (1).
(3) Disconnect the flexible cable (2) and two connectors (3).
(4) Remove two screws (4) and two ground wires (5) and (6).
(5) Release four claws and remove two screws (7).
(6) Remove the front panel (8).
Fig. 2-1-2
1-1-3. Tray Door
(1) Remove the front panel. (Refer to item 1-1-2.)
(2) Remove the Front (R) PC board. (Refer to item 1-2-4 (2) to (4).)
(3) Remove the spring (1).
(4) Remove the tray door (2) while slightly bending it.
Fig. 2-1-3
Screw (4)
Screw (4)
Connector (3)
Connector (3)
Claw
Claw
Claws
Screws (7) Front panel (8)
Ground
wire (5)
Ground wire (6)
Flexible cable (1)
Flexible cable (2)
Tray door (2)
Spring (1)
1-1-4. RAM Drive
(1) Remove the top cover. (Refer to item 1-1-1.)
(2) Remove the front panel. (Refer to item 1-1-2.)
(3) Disconnect the flexible cable (1).
(4) Remove the piece of tape (2).
(5) Disconnect the connector (3).
(6) Remove two pieces of tape (4).
(7) Remove three screws (5), and then remove the acrylic board (6).
(8) Remove the screw (7) and the ground wire (8).
(9) Remove four screws (9), and then remove the RAM drive (10).
(Note)
After replacing, tape on three points of (2) and (4) as they were.
Fig. 2-1-4
Screw (7)
Connector (3)
Screws (9)
Screws (5)
Tape (4)
Tape (2)
Acrylic board (6)
RAM drive (10)
Ground wire (8)
Flexible cable (1)
1-1-5. Fan
(1) Remove the two pieces of tape (1).
(2) Cut off the binding band (2).
(3) Disconnect the connector (3).
(4) Remove four screws (4), and then remove the fan (5).
(Note)
• After replacing, tape on two points (1) as they were.
• Pass the wire (6) underneath the folded part of the acrylic board.
Fig. 2-1-5
1-1-6. Rear Panel
(1) Remove the fan. (Refer to 1-1-5.)
(2) Remove ten screws (1) and the rear panel (2).
Fig. 2-1-6
Connector (3)
Screws (4)
Tape (1)
Lead wire (6)
Pass the lead (6)
underneath the
folded porton
Binding band (2)
Tape (1)
Fan (5)
Fan (6)
Acrylic board
Screws (1)
Screws (1)
Rear panel (2)
Altri manuali per D-R1SU
2
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Toshiba Registratore digitale
Toshiba
Toshiba RD-XS34S Manuale utente
Toshiba
Toshiba RD-XS27KE Manuale utente
Toshiba
Toshiba SD-100X Manuale utente
Toshiba
Toshiba RD-87DTKF Manuale utente
Toshiba
Toshiba RD-XS54SU Manuale utente
Toshiba
Toshiba RD-XS32SB Manuale utente
Toshiba
Toshiba Surveillix EAV16-480 Manuale utente
Toshiba
Toshiba RD-XS52SU Manuale utente
Toshiba
Toshiba RD-97DTKB Manuale utente
Toshiba
Toshiba KV-HD01A Manuale utente
Toshiba
Toshiba NVSe Manuale utente
Toshiba
Toshiba RD-XS30B Manuale utente
Toshiba
Toshiba D-RW2SU Manuale utente
Toshiba
Toshiba RD-X2 Manuale utente
Toshiba
Toshiba SD-1600 Manuale utente
Toshiba
Toshiba D-R4SU Manuale utente
Toshiba
Toshiba IPR16-X Manuale utente
Toshiba
Toshiba RD-XS30B Manuale utente
Toshiba
Toshiba D-VR41KF Manuale utente
Toshiba
Toshiba D-VR3SU Manuale utente
