Toshiba 29A3DE Guida rapida

SCHEMATIC DIAGRAM MODEL : 29A3DE / 29A3E / 29A3SH

WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY

PRECAUTION" AND "PRODUCT SAFETY NOTICE" ON THE MANUAL FOR THIS MODEL.

CAUTION: The international hazard symbols "*" in the schematic diagram and the parts list designate components

which have special characteristics important for safety and should be replaced only with types identical to those in the

original circuit or specified in the parts list. The mounting position of replacements is to be identical with originals.

Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE on the MANUAL for this

model. Do not degrade the safety of the receiver through improper servicing.

4. Voltages read with DIGITAL MULTI-METER from point indicated to chassing ground, using a color bar signal with all

controls at normal, line voltage 220 volts.

5. Waveforms are taken receiving color bar signal with enough sensitivity.

6. Voltage reading shown are nominal values and may vary ±20% except H.V.

NOTE:

1. RESISTOR Resistance is shown in ohm [K = 1.000, M = 1.000.000]. All resistors are 1/6W and 5%

tolerance carbon resistor, unless otherwise noted as the following marks.

1/2R = Metal or Metal oxide of 1/2 watt 1/2S = Carbon compsistion of 1/2 watt

1RF = Fuse resistor of 1 watt 10W = Cement of 10 watt

K = ±10% G = ±2% F = ±1%

2. CAPACITOR Unless otherwise noted in schematic, all capacitor values less than 1 are expressed in

?F, and the values more than 1 in pF.

All capacitors are ceramic 50V, unless otherwise noted as the following marks.

Electolytic capacitor Mylar capacitor

3. The parts indicated with " *" have special characteristics, and should be replaced with identical parts only.

–6 –

GENERAL ADJUSTMENTS

SPECIFIC INFORMATIONS

SERVICE MODE

1. ENTERING TO SERVICE MODE

(Service mode display)

Item

Data

3) While pressing the obutton,

press MENU button on TV set.

2) Press obutton again to

keep pressing.

2. DISPLAYING THE ADJUSTMENT MENU

1) Press MENU button on TV.

3. KEY FUNCTION IN THE SERVICE MODE

The following key entry during display of adjustment menu provides special functions.

A single horizontal line ON/OFF: - / - - button (on Remote) or abutton (on TV)

Test signal selection : abutton (on Remote)

Selection of the adjustment items : Channel s/t(on TV or Remote)

Change of the data value : Volume ;+/–(on TV or Remote)

Adjustment menu mode ON/OFF : MENU button (on TV)

Initialization of the memory (QA02) : CALL + Channel button on TV (s)

Reset the count of operating protect

circuit to “00”: CALL + Channel button on TV (t)

“RCUT”selection : 1 button

“GCUT”selection : 2 button

“BCUT”selection : 3 button

“CNTX”(or “SCNT”) selection : 4 button

“COLC”selection : 5 button

“TNTC”selection : 6 button

Test audio signal ON/OFF (1kHz) : 8 button

Self diagnostic display ON/OFF : 9 button

1) Press obutton once on

Remote Control.

Adjustment mode

Press

Service mode

Item

Data

Color thickness correction

note: Displayed differently as shown below, de-

pending on the setting of the receiving color

system.

COLP (PAL)

COLC (NTSC)

COLS (SECAM)

CAUTION : Never try to perform initialization unless you have changed the memory IC.

* The key function marked with are not usable to control in the Test signal for some model.

–7 –

GENERAL ADJUSTMENTS

SPECIFIC INFORMATIONS

4. SELECTING THE ADJUSTING ITEMS

1)Every pressing of CHANNEL sbutton in the service mode changes the adjustment items in the order of table-2.

(tbutton for reverse order)

Refer to table-2 for preset data of adjustment mode.

(See SETTING & ADJUSTING DATA on page 15)

5. ADJUSTING THE DATA

1) Pressing of VOLUME ;+/–button will change the value of data in the range from 00H to FFH. The variable range

depends on the adjusting item.

6. EXIT FROM SERVICE MODE

1) Pressing POWER button to turn off the TV once.

■INITIALIZATION OF MEMORY DATA OF QA02

After replacing QA02, the following initialization is required.

1. Enter the service mode, then select any register item.

2. Press and hold the CALL button on the Remote, then press the CHANNEL sbutton on the TV. The initialization of QA02 has

been complated.

3. Check the picture carefully. If necessary, adjust any adjustment item above.

Perform “Auto search Memory”on the owner’s manual.

CAUTION: Never attempt to initialize the data unless QA02 has been replaced.

7. TEST SIGNAL SELECTION

1) Every pressing of abutton on the Remote Control changes the built-in test patterns on screen as described below

in SERVICE MODE.

Signals Picture

•Red raster

•Green raster

•Blue raster

•All Black

•All White

•Black & White

•Black cross-hatch

•White cross-hatch

•Black cross-dot

•White cross-dot

•Black cross-bar

•White cross-bar

•Black cross-bar

on green raster

•H signal (white)

•H signal (black)

* The signals marked with are not usable to display in the Test signal for some model.

Signal off NTSC signals (14 patterns)

PAL signals (14 patterns)

–8 –

GENERAL ADJUSTMENTS

SPECIFIC INFORMATIONS

8. SELF DIAGNOSTIC FUNCTION

1) Press “9”button on Remote Control during display of adjustment menu in the service mode.

The diagnosis will begin to check if interface among IC’s are executed properly.

2) During diagnosis, the following displays are shown.

23******

POWER : 00

BUS LINE : OK

BUS CONT : OK

BLOCK : UV V1 V2

QV01

Part number of microcomputer (QA01)

Operation number of protecting circuit ----“00”is nor-

mal.

When indication is other than “00”, overcurrent apts to

flow, and circuit parts may possibly be damaged.

BUS LINE CHECK ----“OK”is normal.

“SDA1-GND”------------- SDA-GND short circuit.

“SCL1-GND”-------------- SCL-GND short circuit.

“SCL1-SDA1”------------- SCL-SDA short circuit.

BUS CONT ----“OK”is normal.

When indication shows “Q uuu NG”, the device with

the number may possibly be damaged.

BLOCK

UV : TV reception mode

V1 : VIDEO 1 input mode (a1)

V2 : VIDEO 2 input mode (a2)

Indicated color of mode now selected : Green and Red

Indicated color of other modes : White

Green : Normal

Red : The microcomputer operates to provide judgement

of no video signal. The red color is still indicated

though the signal is input, failure may exist in input

signal line including QV01.

QV01 : In case of indication green ---Normal

In case of indication red with input signal----

Failure may exist in output line including QV01.

NOTE: Component which controls character display on

screen is QT01 (TELETEXT IC.). If this display

function fails to operate due to damage in QT01,

self diagnosis procedure is as follows.

(1) In case that power indicator is blinking with

interval of 0.5 seconds; it means protecting cir-

cuit (Current limiter) is operating, and circuit

components may possibly be damaged. Check

related components.

(2) In case that power indicator is blinking with

interval of 1 second; Protecting circuit does

not operate, but a part of Bus line does not

operate normally. Check Bus line.











* The items marked with are not usable to display in the SELF DIAGNOSTIC FUNCTION for some model.

–9 –

GENERAL ADJUSTMENTS

SPECIFIC INFORMATIONS

DESIGN MODE

1. ENTERING TO DESIGN MODE

ITEM

DATA

S D Press

(Design mode) (Adjustment mode)

Press

3) Press MENU button on TV.

2) While pressing o(or CALL) button on

Remote and press MENU button on TV.

1) Select the Service mode.

2. SELECTING THE ADJUSTING ITEMS

Every pressing of CHANNEL tbutton in the design mode changes the adjustment items in the order of table-3.

(sbutton for reverse order)

Refer to table-3 for data of design mode.

(See SETTING & ADJUSTING DATA on page 15)

3. ADJUSTING THE DATA

Pressing of VOLUME sor tbutton will change the value of data.

When QA02 is initialized, items “OPT0”and “OPT1”of DESIGN MODE are set to the data of the representative model of this

chassis family.

Therefore, because ON-SCREEN specification remains in the state of the representative of model. This model is required to

reset the data of items “OPT0”and “OPT1”.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Toshiba TV

Toshiba

Toshiba MW27FN1/R Manuale utente

Toshiba

Toshiba 46RV525U - 46" LCD TV Manuale utente

Toshiba

Toshiba CF32G40 Manuale utente

Toshiba

Toshiba 27AFX55 Manuale utente

Toshiba

Toshiba CX35F70 Manuale utente

Toshiba

Toshiba 2837DD Manuale utente

Toshiba

Toshiba 32XV566D Manuale utente

Toshiba

Toshiba 24L4200U Istruzioni per il montaggio

Toshiba

Toshiba 42WH18B, 50WH18B Manuale utente

Toshiba

Toshiba CX32H60 Manuale utente

Toshiba

Toshiba TheaterWide 23HL84 Manuale utente

Toshiba

Toshiba PW33 Series Manuale utente

Toshiba

Toshiba 24D3753DB Manuale utente

Toshiba

Toshiba Stasia 23WL46 Manuale utente

Toshiba

Toshiba 55U7653DB Manuale utente

Toshiba

Toshiba TheaterWide 23HL85 Manuale utente

Toshiba

Toshiba 14R01B Manuale utente

Toshiba

Toshiba 24 WN3D Series Manuale utente

Toshiba

Toshiba CX36F67 Manuale utente

Toshiba

Toshiba 32Z17B Manuale utente

Toshiba

Toshiba 32HL84 - TheaterWide HD - 32" LCD TV Manuale di servizio

Toshiba

Toshiba 28Z13B Manuale utente

Toshiba

Toshiba 40XF350P Manuale utente

Toshiba

Toshiba 20AS24 Manuale utente

Manuali TV popolari di altre marche

Philips

Philips Colour Television Manuale utente

Philips

Philips 42PF9630A/37 Manuale utente

Hitachi

Hitachi 32FX48B Manuale utente

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Manuale utente

Changhong Electric

Changhong Electric uhd55b6000is Manuale utente

Philips

Philips Matchline 21CE7551 Manuale utente

Panasonic

Panasonic Genus TX-G10 Manuale utente

Philips

Philips 25PT4523-16 Manuale utente

Sony

Sony XBR-100Z9D Manuale utente

Philips

Philips PR0930X3 Manuale utente

Philips

Philips Brilliance 231P4QPY Manuale utente

Samsung

Samsung 55S9 B Series Manuale utente

Philips

Philips 32HF9385D Guida alla risoluzione dei problemi

Sharp

Sharp LC-40FI5012E Manuale utente

Loewe

Loewe Table Stand Reference 55 Manuale utente

Philips

Philips 32PFH5300 Manuale utente

Sylvania

Sylvania 6427FB Manuale utente

Sanyo

Sanyo CE19LD90N-B Manuale utente