Totally Wicked Arc Sigma Manuale utente
USER MANUAL
2 3
Tank
connection
Power
button
UP
adjustment
button
DOWN
adjustment
button
Mouthpiece
Glass section
Airow
control ring
Atomizer head
Tank base
LED
screen
USB
charging
port
YOUR ARC SIGMA
4 5
REMOVING THE
ATOMIZER HEAD
PRIME THE
ATOMIZER HEAD
Wait 5 minutes before vaping
a new atomizer head.
x2
6 7
FILL THE TANKREATTACH THE TANK BASE
ADJUST AIRFLOW
8 9
TURN POWER ON
x5
On/O
Press the UP and DOWN
buttons to adjust the power
SET WATTAGE
10 11
CHARGE THE BATTERYVAPING
Press and hold
to vape.
12 13
PRIMING THE ATOMIZER HEAD
It is important to “prime” a new atomizer head
before rst use. Failure to do so can damage
the atomizer head.
Remove the tank from the arc Sigma battery
by unscrewing at the tank base. Turn the tank
upside down, then unscrew the tank base
from the glass section of the tank. Remove
the atomizer head by pulling straight out, drip
a few drops of e-liquid onto the cotton wick
through the openings on the sides of the
atomizer head, and push back into the tank.
Screw the base back onto the tank and ret
to the battery.
ATOMIZER HEAD LIFESPAN
Atomizer heads do not last forever and
need to be replaced periodically. Lifespan is
generally from a few days to several weeks,
depending on power used, vaping style,
avour and type of e-liquid. A slight burnt
taste, general loss of vapour production,
or a reduction in avour intensity can all be
indicators that the atomizer head requires
replacement.
FILLING THE TANK
Unscrew the top section of the GT Air Slim tank
and ll the tank through one of the apertures
either side of the central air hole. Do not allow
liquid to enter the central air hole. Ret the top
section of the tank.
Note: To avoid leaking, ensure an air gap of
2mm remains above the e-liquid after lling.
After priming a new atomizer head and lling
the tank, it is recommended to wait 5 minutes
to ensure the atomizer head is fully saturated.
POWERING ON AND OFF
Press the power button 5 times in quick
succession to turn the arc Sigma on. To turn
the device o again, press the power button 5
times quickly.
SETTING THE CORRECT WATTAGE
The arc Sigma has adjustable wattage that
can be set from 1 - 40W. Use the adjustment
buttons on the battery to increase or decrease
the wattage. We recommend a wattage of 11W
with the supplied atomizer head but feel free to
experiment to nd your favourite setting.
Tip: Press and hold down either of the
adjustment buttons to make speedy changes
to the wattage.
USING YOUR ARC SIGMA
14 15
VAPING
Press and hold the power button as you inhale
the vapour, the screen will display a vape timer
while the power button is held down.
ADJUSTING THE AIRFLOW
To adjust the airow to your personal
preference, rotate the airow control ring
located at the bottom of the tank. The more
area exposed behind the slots in the airow
ring, the more open the air draw will be.
E-LIQUID LEVEL
To prevent the atomizer head from becoming
dry and burning prematurely, ensure the
e-liquid level does not drop below the cotton
inlets on the atomizer head, visible through
the glass section of the tank.
CHARGING THE BATTERY
To charge the battery, connect the charge
port on the battery to a USB port or suitable
wall adaptor with the supplied charging cable.
The screen will display an animated battery
icon while charging, once the battery is fully
charged the screen will switch o completely.
REPLACING THE ATOMIZER HEAD
Remove the tank from the arc Sigma battery
by unscrewing at the tank base. Invert the tank
and unscrew the base. Remove the atomizer
head from the tank by pulling, and insert a new
atomizer head. Before tting a new atomizer
head, remember that it will need priming
as described in the section “Priming the
Atomizer Head”.
Reminder: After priming a new atomizer head
it is recommended to wait 5 minutes before
vaping to ensure the atomizer head is fully
saturated.
STEALTH MODE
If stealth mode is enabled, the display will not
activate when pressing the power button to
vape. The display will still activate whenever
the adjustment buttons are pressed to make
changes to wattage. To enable stealth mode,
ensure the arc Sigma is switched on, then
press and hold down the power and down
adjustment buttons at the same time, the
screen will display “Stealth ON” when enabled.
Repeat the process to disable stealth mode,
the screen will display “Stealth OFF” when
disabled.
USING YOUR ARC SIGMA
16 17
KEY LOCK MODE
Key lock mode prevents accidental changes
to the wattage. If key lock mode is enabled,
the screen will display “Lock” if the adjustment
buttons are pressed. Adjustments to wattage
cannot be made until key lock has been
disabled. To enable key lock mode, ensure the
arc Sigma is switched on, then press and hold
down both adjustment buttons at the same
time, then screen will display “Lock” when
enabled. Repeat the process to disable key
lock mode, the screen will display “Unlock”
when disabled.
ROTATING THE DISPLAY
Switch the arc Sigma o, then press and hold
down both adjustment buttons at the same
time to rotate the display 180°. Then switch
the arc Sigma back on.
PUFF & VAPE DURATION
If the pu counter and vape duration display is
enabled, the arc Sigma will display the number
of the times the power button has been
pressed to vape and total time spent vaping in
seconds. To enable the counter, quickly press
the power button 4 times while the arc Sigma
is switched on. Pu counter is displayed on
the rst row while vape duration is displayed
on the second row. To reset the number of
recorded pus to zero, press and hold down
the power and up adjustment buttons at the
same time. To reset the vape duration to zero,
press and hold down the power and down
adjustment buttons at the same time. Quickly
pressing the power button 4 times switches
the arc Sigma back to wattage display mode.
USING YOUR ARC SIGMA
18 19
ATOMIZER HEAD PROTECTION
If the power button is held down for longer
than 10 seconds while vaping, the screen
will display “Over 10s” and the arc Sigma
will refuse to power or produce any vapour.
Releasing the power button will allow normal
operation to resume.
LOW VOLTAGE PROTECTION
If battery voltage drops to 3.3V, “Lock” will
be displayed onscreen and the arc Sigma
will refuse to power or produce any vapour.
Charge the battery using the steps outlined
in “Charging the Battery” to unlock the arc
Sigma allowing normal operation to resume.
LOW BATTERY ALERT
If battery drops to 10% charge, the power
symbol on screen will ash continuously. This
is a reminder the battery will need charging
soon.
SHORT CIRCUIT PROTECTION
If an atomizer short circuit occurs, the screen
will display “Atomizer short” and the arc Sigma
will refuse to power or produce any vapour.
Replacing the atomizer head should allow
normal operation to resume. To replace the
atomizer head follow the steps outlined in
“Replacing the Atomizer Head”.
NO ATOMIZER DETECTED PROTECTION
If no atomizer head is detected, the screen will
display “No atomizer” and the arc Sigma will
refuse to power or produce any vapour. Ensure
the atomizer head is fully pushed into the
tank and the tank base is correctly screwed
onto the tank, then t the tank back onto
the battery. If the “No atomizer” message
continues, replacing the atomizer head should
allow normal operation to resume. To replace
the atomizer head follow the steps outlined in
“Replacing the Atomizer Head”.
TEMPERATURE ALERT
If the temperature of the arc Sigma exceeds
the maximum safe operating temperature,
the screen will display “Device Too Hot” and
the arc Sigma will refuse to power or produce
any vapour. Stop vaping and allow the arc
Sigma to cool down for normal operation to
resume.
PROTECTIONS
Indice
Altri manuali Totally Wicked Vaporizzatore
Totally Wicked
Totally Wicked Otium Vape-Pen Manuale utente
Totally Wicked
Totally Wicked TORNADO EX EDGE Manuale utente
Totally Wicked
Totally Wicked intu PLUS Manuale utente
Totally Wicked
Totally Wicked INTU PRO Manuale utente
Totally Wicked
Totally Wicked TORNADO GTL Manuale utente
Totally Wicked
Totally Wicked INTU PRO MINI Manuale utente
