Totem LADYBUG Manuale utente
It is a good idea to
start every step in-
serting nuts into
beams (if the step
requires).
Use the back of the
screwdriver to push
in the nuts.
After entering the
fi rst slot, nuts tend
to tilt. Use your
thumb to push it
back straight, and
then again use the
screwdriver to in-
sert the nut all the
way in.
Push Nylon
Standoff with your
thumb while tight-
ening it with the
wrench.
Some of the nuts
are missing threads.
This is a manufac-
turing issue and we
are working on it. In
the mean time, we
add few extra nuts.
We apologize for
the inconvenience.
Use Beam/Bolt
ruler to determine
the length of beams
and bolts.
For more tips, please visit the link below:
https://totemmaker.net/blog/totem-mechanics-for-beginners/
STARTING TIPS
Inserting nuts (1) Inserting nuts (2) Faulty threads Tightening
standoff s
Ruler
PART LIST
1x Board 30x100 10x Beam 90 mm 4x Bolt M1.6x3 34x Bolt M3x6 4x Bolt M3x8 8x Bolt M3x12 2x Bolt M3x16
4x Bolt M3x20 2x Bolt M3x25 8x 2-Hole Simple
Bracket
2x L-Twisted
Bracket
2x L-Twisted Mirror
Bracket
6x Strip Bracket
60 mm (12 Holes) 2x Zip Tie
14x Lock Nut M3 4x Nut M3 5.5x5.5 42x Nut M3 6x10 4x Nylon Nut M3 4x Nylon Standoff
M3x8 mm
10x Nylon Spacer
4 mm
2x Nylon Spacer
8 mm
1x Rechargeable
Battery 2x N20 Motor 1x Mini Control
Board
2x Mini DC Motor
Bracket 2x N20 Motor Hub 2x Googly Eye 1x Ladybug Head
1x Ladybug Shell 6x Moon Boot 4x Ladybug Dot 1x Totem
Screwdriver 1x Totem Wrench 1x Mini
Screwdriver 1x Battery Charger
1
2x Beam 90 mm 4x Bolt M3x6
4x 2-Hole Simple
Bracket 12x Nut M3 6x10
Repeat this step twice.
2x
2x L-Twisted Bracket 2x L-Twisted Bracket
4x Bolt M3x20 4x Bolt M3x6
2x Step 1 Assembly
2
Repeat this step twice.
2x
4x Bolt M3x6 2x Step 2 Assembly
2x Step 3 Assembly
2x Beam 90 mm 4x Bolt M3x6
4x 2-Hole Simple
Bracket 8x Nut M3 6x10
Repeat this step twice.
Repeat this step twice.
2x
2x
3
4
Repeat this step twice.
2x
5
Use Mini Screwdriver
for this step.
4x Nut M3 6x10 4x Bolt M3x8
2x Step 4 Assembly 2x Step 5 Assembly
6
4x Bolt M1.6x3 2x N20 Motor
2x N20 Motor Bracket
Repeat this step twice.
2x
Make sure motor
cables go on top
7
2x Nut M3 6x10 2x N20 Motor Hub
2x Bolt M3x25
Repeat this step twice.
2x
Tighten the
bolt fi rmly.
8
2x Nylon Spacer 4 mm 4x Bolt M3x6
2x Step 6 Assembly 2x Step 7 Assembly
Repeat this step twice.
2x
Prepare N20 Motor Hub:
screw bolts half way in
before placing hub on the
shaft of motor.
One of the bolts must hit
the at side of the shaft.
Tighten both bolts evenly
to keep the hub straight.
9
4x Beam 90 mm 4x Nut M3 6x10
4x Lock Nut M3 4x Bolt M3x12
2x Step 8 Assembly 4x Nylon Spacer 4 mm
Repeat this step twice.
2x
Use Totem Wrench
for Lock Nuts.
Do not over-tighten Lock
Nuts. Legs have to move
freely, but not to wobble.
#8
#8
#4
#4
# indicates number
of circular slot.
indicates counting
direction.
Indice
Altri manuali Totem Robotica
Totem
Totem LIFT MOBILE Manuale utente
Totem
Totem Mini Lab Scheda informativa del prodotto
Totem
Totem MINI SPIDER Manuale utente
Totem
Totem Mini Trooper Manuale utente
Totem
Totem Gripper Bot Manuale utente
Totem
Totem T.R.U.C.K. Manuale utente
Totem
Totem MINI SHOOTER Manuale utente
Totem
Totem LarvaMobile Manuale utente
Totem
Totem Lucas the Robot Manuale utente
Totem
Totem Motor-Wheel Platform Manuale utente
