Touch Revolution K32A Series Manuale utente
K32A Series
Touch Screen LCD Monitors
USER’s GUIDE
Rev.A
The information contained in this document is subject to change without notice.
This document contains proprietary information that is protected by copyright. All rights
are reserved. No part of this document may be reproduced,translated to another language
or stored in a retrieval system, or transmitted by any means, electronic, mechanical,
photocopying, recording, or otherwise, without prior written permission. Windows is a registered
trademark of Microsoft, Inc. Other brand or product names are trademarks of their respective
holders.
The test results show that this device meets the FCC rules. Those limits are set to protect
residential areas from the devices with harmful emission. This device will produce, use and
radiate radio frequency energy. In addition, failure to follow the user’s manual to install or use
this device might produce harmful interference with radio communication. Not withstanding
the foregoing, it does not guarantee that this type of harmful interference does not occur in
some special installations. The interference caused by this device to the reception of radio
or television signals may be verified by turning it on and off. Any changes or modifications to
this TFT LCD would void the user’s authority to operate this device.
Important Recycle Instructions:
LCD lamps inside this product may contain mercury. This product may contain
other electronic waste that can be hazardous if not disposed of properly. Recycle or
dispose in accordance with local, state, or federal Laws. For more information, contact
the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp specific disposal information
check WWW.LAMPRECYCLE.ORG.
Table of Contents
Usage Notice
Precautions............................................................................................................................. 1
Introduction
About K32A Series ................................................................................................................. 2
Touch Screen for K32A Series ............................................................................................... 2
Package Overview ...................................................................................................... 3
Installation
Product Overview ........................................................................................................ 4
Front View .............................................................................................................. 4
Bottom View ........................................................................................................... 4
VESA Mount for Your Monitor ...................................................................................... 5
Connecting the Display (Figure 7.1)............................................................................. 6
(Figure 7.1) ............................................................................................................. 7
User Controls
Rear Panel Controls .................................................................................................... 8
How to Use the OSD Menus ........................................................................................ 9
On-Screen Display Menus ..........................................................................................10
Appendix
Troubleshooting..........................................................................................................11
Warning Signal ...........................................................................................................12
No Signal ...............................................................................................................12
Going to Sleep........................................................................................................12
Out of Range..........................................................................................................12
Product Dimensions ...................................................................................................13
Bezel Free .............................................................................................................13
Compatibility Modes ...................................................................................................14
Touch Screen Driver Installation .................................................................................15
K32A Optional Calibration Tool Install .....................................................................15
Usage Notice
! Warnin
g
- To prevent the risk o
f
fi
re or shock hazards, do not expose
this product to rain or moisture.
! Warnin
g
- Please do not open or disassemble the product as this ma
y
cause
e
l
ec
tri
c
s
h
oc
k.
Precautions
Follow all warnings, precautions and maintenance as recommended in this user’s manual to
maximize the life of your unit.
Do:
• Turn off the product before cleaning.
• Touch screen surface may be cleaned using a soft clean cloth moistened with mild
window glass commercial cleaners or 50/50 mixture of water and isopropyl alcohol.
• Use a soft cloth moistened with mild detergent to clean the display housing.
Don’t:
• Do not touch the LCD Display screen surface with sharp or hard objects.
• Do not use abrasive cleaners.
• Do not operate the product under the following conditions:
- Extremely hot, cold or humid environment.
- Areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
- In direct sunlight.
1
Introduction
About K32A Series
The K32A Series is a 31.5" flat panel screen with an active matrix, thin-film transistor (TFT)
liquid crystal display (LCD).
Features include:
• Direct Analog signal input
• Direct Digital signal input
• Active matrix TFT LCD technology
• 1920 x 1080 resolution
• 31.5" viewable display area - 16:9 aspect ratio
• 31.47 ~ 67.5 KHz horizontal scan
• 47 ~ 63 Hz high refresh rate
• 0.36375mm x 0.36375mm pixel pitch
• Auto adjustment function
• Multilingual OSD user control
• 400mm x 200mm VESA mount
• K32A Series - Projected Capactive touch screen with USB controller
• Audio - 8W x 2
Touch Screen for K32A Series
• Project Capacitive touch screen for finger input only
• Surface: Clear glass
• Interface: USB controller
• HID Multi-Touch: Windows 7
2
Package Overview
3
LCD Display Power Cord
USB Cable (A to B) Audio-in Cable
Quick Start Guide
VGA Signal Cable
DVI-D Cable
Handle Screw Caps
4
Installation
Product Overview
• Front View
• Bottom View
AC IN
AUDIO OUT
Remote Key
COM OUT
VGA IN
DVI IN
AUDIO IN
USB
COM IN
VESA Mount for Your Monitor
This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface
standard which defines a physical mounting interface for flat panel monitors, and
corresponding with the standards of flat panel monitor mounting devices, such as wall and
table arms. The VESA mounting interface is located on the back of your monitor.
To mount the monitor on a UL certified swing arm or other mounting fixture, follow the
instructions included with the mounting fixture to be used.
M6
400.0mm
200.0mm144.2mm
! Warning!
Please select the proper screws!
The distance between the back cover surface and the bottom of the screw hole
is 8 mm. Please use four M6 screws diameter with proper length to mount your
monitor.
Please note: the mounting stand must be able to support at least 44.1 lbs (20Kg).
5
6
Connecting the Display (Figure 7.1)
To setup this display, please refer to the following figure and procedures.
1. Be sure all equipment is turned off.
2. Connect the AC power cord to the power connector on the monitor and the other end
into an electrical outlet (7.1).
3. Connect the D-SUB or DVI cable from the display’s VGA input connector to the D-SUB
or DVI connector of your host computer and tighten the screws (7.1).
4. Connect the Audio-In cable from the audio input port of your display to the Audio-out port
of your computer (7.1).
5. Connect the USB cable from USB port of your display to USB port of your computer (7.1).
6. Once the touch screen is configured, the monitor is ready for use.
! Notice!
To ensure the LCD display works well with your computer, please configure the
display mode of your graphics card to make it less than or equal to 1920 x 1080
resolution and make sure the timing of the display mode is compatible with the LCD
display.
We have listed the compatible “Video Modes” of your LCD display in the appendix
(on page 14) for your reference.
7
(Figure 7.1)
Indice
Altri manuali Touch Revolution Monitor
