TouchIT Fusion Manuale utente
TouchIT Fusion
Manual
TouchIT Technologies, Inc
IMPORTANT SAFETY INSTRUCTIONS
1. Please read these instructions carefully before using the product and keep them
safe for later reference.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet (power socket) before cleaning. Clean
the product with a damp soft cloth. Do not use liquid or aerosol cleaners as it may
cause permanent damage to the screen.
4. Caution of use varies from model to model; please observe appropriate
operation as per model in use.
5. Do not place this product on an unstable cart, stand, or surface which may
cause damage or harm to the product or individual.
6. Slots and openings on the cabinet, in the back cover or in the bottom, are for
ventilation; to ensure reliable operation and to prevent from overheating, these
openings must not be blocked or covered at any time. The openings should never
be placed near or over a radiator, heat source, or placed in a built-in installation
unless proper ventilation space (min. 2 inches/5cm of gap) is provided.
Section 1
IMPORTANT SAFETY INSTRUCTIONS
Please read these instructions carefully before
using the product and keep them safe for
future reference.
Safety Instructions
2
7. This product should be operated from the type of power
indicated on the marking label. If you are not sure of the type of
power available, consult your dealer or local service company.
8. This product is equipped with a 3-wire grounding type power
plug, a plug having a third (grounding) pin. This plug will only fit
into a grounding-type power outlet. This is a safety feature. If you
do not have proper outlet to insert the plug, contact your
electrician to replace your obsolete outlet. Do not break the
ground pin and circumvent the grounding.
9. Do not allow anything to rest, or persons to walk on the power
cord.
10. If an extension cord is used with this product, make sure that
the total ampere rating plugged into the extension cord does not
exceed the maximum ampere rating of the extension cord.
11. Never insert any object/tool of any kind through housing slots
of this product as they may touch dangerous voltage points or
short out components that could result in risk of fire or electric
shock. Never spill liquid of any kind on the product (except IP-
rated models).
12. Do not attempt to service this product yourself, always refer
to qualified or authorized person for the servicing of this product.
13. Unplug this product from the wall outlet and contact a
qualified service provider in the following circumstances:
When the power cord or plug is damaged, frayed or broken.
In the event that liquid has been spilled into the product (except
IP-rated models).
3
2-1!About the Product
The TouchIT Fusion is made of TFT LCD panel and microprocessor-controlled
main board. It is designed to meet the demanding performance requirements of
education/schools, public premises, corporate, and industrial applications.
2-2!Notice
1.!Do not use any sharp object on the original LCD panel surface if the model is
supplied without protective glass.
2.!Do not use corrosive or abrasive detergents, waxes or solvents for cleaning.
Use only a dry or damp cloth and use with clean water when cleaning.
3.!Use qualified and safety-approved AC power cord only.
2-3!Check List
When opening the carton, please make sure that all the items listed below are
present:
Section 2
CHAPTER CONTENTS
2-1!About the Product
2-2!Notice
2-3!Check List
Introduction
4
1.!TouchIT Fusion ×1
2.!TouchIT Fusion Stand ×1
3.!Screw M6*L10mm ×6
4.!Audio cable×1(already plugged in TouchIT Fusion)
5.!DVI cable×1(already plugged in TouchIT Fusion)
6.!VGA cable (male-to-male) ×1
7.!Power cord(male-to-female) ×1(already plugged in TouchIT
Fusion)
8.!Power cord ×1
9.!USB cable ×1 (already plugged in TouchIT Fusion)
10. Remote control ×1, battery included
If any items are missing or damaged, please contact your dealer
immediately.
The following items are optional:
1.!VGA cable (male-to-female) (optional) for VGA out
application
2.!RS232 to RS485 adapter (optional)
3.!HDMI-to-DVI adapter (optional)
5
3-1 Installing the TouchIT Fusion
The TouchIT Fusion comes with the Operating System, and the software pre-
installed. The LCD Monitor needs to be attached to the motorized trolley. This is a
simple and straight forward process.
3-1-1. Lock the wheels in place by pressing down on the break.
Section 3
POWER AND SIGNAL CONNECTIONS
3-1-1. Lock the wheels in place
3-1-2. Connecting the power cord to the AC
inlet.
3-1-3. Attaching the LCD Monitor
3-1-4. Securing the LCD Monitor in position.
3-1-5. Connecting the TouchIT Fusion to an
AC Outlet
Installing the TouchIT Fusion
6
3-1-2. Connecting the power cord to the AC inlet.
7
3-1-3. Slowly lower the LCD Monitor onto the hanging brackets that are on the motorized trolley. See diagram below.
8
3-1-4. Secure the LCD in position with the 6 fastening bolts (M6*L10mm), see hole locations on the diagram below.
9
Indice
