Toyota Supra 1997 Istruzioni operative
Manual Name Pub. No.
7M−GE Engine Repair Manual
TOYOTA SUPRA Chassis and Body
Repair Manual
TOYOTA SUPRA Chassis and Body
Repair Manual Supplement
TOYOTA SUPRA Electrical Wiring
Diagram Manual
TOYOTA SUPRA Repair Manual
(USA and Canada)
TOYOTA SUPRA Electrical Wiring
Diagram Manual (USA and Canada)
Fundamental Body Repair Procedures
Fundamental Painting Procedures
BRM002E
36438E
M/Y Version
M/Y Version
EWD013E
RM036E
RM029E
RM027E
FOREWORD
This repair manual has been prepared to provide information on
the repair methods (including cutting and welding operations,
but excluding painting) recommended by TOYOTA for collision−
damaged body components of the TOYOTA SUPRA.
Applicable models: MA70 series
This manual consists of body repair methods, exploded dia-
grams and illustrations of the body components and other infor-
mation relating to body panel replacement such as handling pre-
cautions, tools, equipment, etc. However, it should be noted that
the front fenders of all TOYOTA models are bolted on and re-
quire no welding.
Body construction will sometimes differ depending on specifica-
tions and country of destination. Therefore, please keep in mind
that the information contained herein is based on vehicles for
general destinations.
For the service of specifications and repair procedures other
than collision−damaged body components of the TOYOTA
SUPRA, refer to the following repair manuals.
All information contained in this manual is the most up−to−date
at the time of publication. However, specifications and proce-
dures are subject to change without prior notice.
TOYOTA MOTOR CORPORATION
1
mm in.
87 3.15
200 7.87
QUARTER PANEL
Cut and Join Location
HOW TO USE THIS MANUAL
Each repair method description provided in Section RE of this manual comprises two pages, divided into
2 blocks (REMOVAL AND INSTALLATION) and includes illustrations to facilitate body repair.
RE−26 BODY PANEL REPLACEMENT−Rear Body Components
QUARTER PANEL (CUT)
REMOVAL
Cut and Join Location
200 mm
80 mm
[Cut and Join Location]
Front
Braze
Rear
1. Cut and join the quarter panel as shown above.
REPLACEMENT PART AND METHOD
(CUT)
Replacement method
(ASSY) Assembly replacement. . . . .
(CUT) Major cutting (less than 1/2 of part used). . . . . .
(CUT−H) Half cutting (about 1/2 of part used). . . .
(CUT−P) Partial cutting (most of part used). . . .
Replacement part
BODY VARIATIONS AND PART LOCATION
Body variations: Non All models. . . .
REMOVAL DIAGRAM
Describes in detail removal of the damaged part involving repair by cutting.
REMOVAL GUIDE
Provides additional information to more efficiently help you perform the removal.
INTRODUCTION
IN-2
mm in.
50.20
1. Before temporarily installing the new part, apply
body sealer to the wheel arch portion.
NOTE:
1) Apply sealer approx. 5 mm (0.20 in.) from the
flange, avoiding any oozing.
2) Apply evenly, approx. 3 −4 mm (0.12 −0.16 in.)
in diameter.
3) For other sealing points, refer to section SU.
BODY PANEL REPLACEMENT−Rear Body Components RE−27
INSTALLATION
Butt Weld
Butt Weld
Body Sealer
Braze
Body Sealer
About 5 mm
2. Temporarily installing the new part and check the fit of
the front door, luggage compartment door and rear
combination lamp.
INSTALLATION DIAGRAM
Describes in detail installation of the new part involving repair by welding and/or cutting, but exclud-
ing painting.
INSTALLATION GUIDE
Provides additional information to more efficiently help you perform the installation.
SYMBOLS
See page IN−4.
ILLUSTRATION OF WELD POINT
Weld method and panel position symbols.
See page IN−5.
INTRODUCTION IN-3
SYMBOLS MEANING ILLUSTRATION
SAW CUT OR
ROUGH CUT
REMOVE BRAZE
(See page IN−5)
SPOT WELD OR
MIG PLUG WELD
WELD POINTS
BRAZE
CONTINUOUS MIG
WELD (BUTT WELD
OR TACK WELD)
BODY SEALER
SYMBOLS
The following symbols are used in the welding Diagrams in Section RE of this manual to indicate cutting
areas and the types of weld required.
INTRODUCTION
IN-4
Remove weld point and panel position
Weld points
REMOVAL
Weld method and panel position
Weld points
INSTALLATION
SYMBOL MEANING ILLUSTRATION SYMBOL
Spot Weld
MEANING ILLUSTRATION
Remove
Weld
Points
(Outside)
Mig Plug
Weld
(Middle)
(Inside)
Spot MIG
Weld
HINT: Panel position syrnbols are as seen from the
working posture.
Illustration of Weld Point Symbols
EXAMPLE:
INTRODUCTION IN-5
GENERAL REPAIR INSTRUCTIONS
Work Precautions
SAFETY
1. Before performing repair work, check
for fuel leaks. If a leak is found, be sure
to close the opening totally.
2. If it is necessary to use a frame in the
area of the fuel tank, first remove the
tank and plug the fuel line.
SAFETY
Never stand in direct
line with the chain when
using a puller an the
body or frame, and be
sure to attach a safety
cable.
VEHICLE PROTECTION
When welding, protect the
painted surfaces, windows,
seats and carpet with heat−
resistant, fire−proof covers.
WRONG
Glass Cover
Safety Cable
Seat Cover
WRONG
SAFETY
Before performing repair work,
disconnect the battery cables.
SAFETY WORK CLOTHES
In addition to the usual mechanic wear, cap and Safety shoes,
the necessary gloves, head protector, glasses, ear plugs, face
protector, dust−prevention mask, etc. should be worn as the
situation demands.
Welder’s
Glasses Body
Mechanic
Stand
Dust−
Prevention
Mask
Face
Protector Ear
Plugs
Head
Protector Welder’s
Gloves
HAND TOOLS
Keeping your hand tools
in neat order will have
an effect on your work
efficiency.
Safety
Shoes
Cotton
Gloves
INTRODUCTION
IN-6
REMOVAL OF ADJACENT
PARTS
When removing adjacent parts
by avoid accidental marring,
etc., wrapping the tools used
and surrounding body parts in
protective tape.
NOTE:
1) Take particular care not
to damage any screw or
clip holes.
2) If you do scratch a
painted surface, retouch
immediatly after. Even a
small scratch will result
in rust and corrosion.
Proper and Efficient Work Procedures
REMOVAL
REMOVAL. OF ADJACENT COMPONENTS
When removing adjacent components, apply
protective tape to the surrounding body and
your tools to prevent damage.
CAUTION:
1. Be especially careful not to damage
screw or clip holes.
2. If the paint is accidently scratched, ap-
ply touch−up paint immediately. Even
the slightest scratch may result in cor-
rosion or appearance of rust.
NO. OF SPOT WELDS
Make a note of the
number of spot welds
for later reference.
NOTE: The number
of spot welds may
vary depending on
the vehicle.
PRE−REMOVAL MEASURING
Before removal or cutting opera-
tions, take measurements in ac-
cordance with the dimension dia-
gram. Always use a puller to
straighten a damaged body or
frame.
CUTTING AREA
Always cut in a straight
line and avoid reinforced
areas.
PRECAUTIONS FOR DRILLING OR
CUTTING
Check behind any area to be drilled or
cut to insure that there are no hoses,
wires, etc., that may be damaged.
Cutting Okay
Corners
Reinforcement
WRONG
INTRODUCTION IN-7
INSTALLATION
WELDING PRECAUTIONS
1. The number of welding spots
should be as follows.
Spot weld: 1.3 x No. of
manufacturer’s spots.
Plug weld: More than No. of
manufacturer’s plugs.
POST−WELDING REFINISH-
ING
1. Always check the welded
spots to insure they are
secure.
2. When smoothing out the
weld spots with a disc
grinder, be careful not to
grind off too much as this
would weaken the weld.
PRE−WELDING MEASUREMENTS
Always take measurements before
installing underbody or engine com-
ponents to insure correct assembly.
After installation, confirm proper fit.
WRONGOKAY
Seal
OKAY WRONG
2. Plug welding should be done
with a MIG (Metal Inert Gas)
welder. Do not gas weld or
braze panels at areas other
than specified.
Safety Glass
Body
Measurement
Diagrams
SPOT WELDING PRECAUTIONS
1. The shape of the welding
tip point has an effect on
the strength of the weld.
2. Always insure that the
seams and welding tip are
free of paint.
SPOT WELD LOCATIONS
Try to avoid welding over
previous spots.
Old
Spot
Locations
New Spot
Locations
Tip Cutter
INTRODUCTION
IN-8
Thickness of
welded portion Size of plug hole
1.0 (0.04) under 5 (0.20) φover
1.0 (0.04) over 6.5 (0.26) φover
REFERENCE: mm (in.)
PREPARATION FOR INSTALLATION
SPOT WELD POINTS APPLICATION OF WELD−THROUGH PRIMER
Less than
3 mm
When welding panels with a
combined thickness of over 3
mm (0.12 in.), use a MIG
(Metal Inert Gas) welder for
plug welding.
NOTE: Spot welding will
not provide sufficient dura-
bility for panels over 3 mm
(0.12 in.) thick.
For treatment
against corrosion,
remove the paint
from the portion of
the new part and
body to be welded,
and apply weld−
through primer.
Air Saw
WRONG
20 −30 mm Puncher
Overlap
ROUGH CUTTING OF JOINTS
For joint areas, rough
cut the new part, leaving
20 −30 mm (0.79 −1.18 in.)
overlap.
MAKING HOLES FOR PLUG WELDING
For areas where a spot welder cannot
he used, use a puncher or drill to make
holes for plug welding.
INTRODUCTION IN-9
ANTI−CORROSIVE TREATMENT
When replacing body panels, always apply body sealer, anti−rust treatment or undercoating according to
the requirements of your country.
CHASSIS RUST−PROOFING
Anti−rust treatment for weld-
ing spots or inside brazed
areas (torque box).
BODY SEALER
Apply body sealer to the
required areas.
Nozzle
Tube
Type Air Gun
Cartridge
Type
UNDERCOATING
Anti−rust treatment for underbody welding
spots and wheel housings.
Spray Gun
Undercoating
(Water base)
Undercoating
(Oil base)
INTRODUCTION
IN-10
Altri manuali per Supra 1997
4
Indice
Altri manuali Toyota Automobile
Toyota
Toyota Highlander 2008 Manuale utente
Toyota
Toyota Camry Hybrid 2020 Manuale utente
Toyota
Toyota RAV4 2002 Manuale utente
Toyota
Toyota SEQUOIA 2019 Manuale utente
Toyota
Toyota RAV4 2003 Manuale utente
Toyota
Toyota Corolla 1997 Manuale utente
Toyota
Toyota 2009 Highlander Hybrid Manuale utente
Toyota
Toyota Avalon 2004 Manuale utente
Toyota
Toyota Sienna 2004 Manuale utente
Toyota
Toyota 2011 HILUX VSS 3 Manuale utente
Toyota
Toyota Yaris 2014 Manuale utente
Toyota
Toyota FJ Cruiser 2014 Manuale utente
Toyota
Toyota Prius 2020 Manuale utente
Toyota
Toyota PRIUS 50 2020 Series Manuale utente
Toyota
Toyota 2009 Sequoia Manuale utente
Toyota
Toyota Prius HSD 2006 Manuale utente
Toyota
Toyota Prius+ Manuale utente
Toyota
Toyota 2013 Tacoma Manuale utente
Toyota
Toyota PRIUS 2009 Manuale utente
Toyota
Toyota Corolla 2020 Manuale utente
