TP-Link Kasa Smart Manuale utente
1. Only cut the exceeded length along the cutting lines of
the light strip after unplugging the light strip.
2. Avoid any sharp corners or turns behind the LED beads.
To avoid damaging your light strip, note the following tips.
CONNECT HARDWARE
STEP 2
Connect all the parts. When connecting the light strip to the
controller, make sure the arrows point at each other.
SET UP
STEP 3
©2021 TP-Link 7106509375 REV1.0.0
*Images may dier from actual products.
Get the Kasa Smart app from the App Store or Google Play.
DOWNLOAD APP
STEP 1
OR
Quick Start Guide
Kasa Smart Light Strip,
Multicolor
Set Up Your Light Strip Installation Tips
≥90° LED
Button Explanations
Control Button
• Press once to turn on / o your light strip
• Press twice to switch preset lighting eects
• Press and hold for 5s, then release to reset only Wi-Fi settings
• Press and hold for 10s to restore factory settings
Tap the button in the app, tap Device > Smart Lights, and
select your model. Follow the instructions in the Kasa Smart
app to complete the setup.
1. Choose a location that avoids static and eases away from
splashing water. Find a clean, dry and smooth surface,
then wipe o the dust.
2. Slowly peel away the 3M adhesive backing and take it out
bit by bit.
3. Stick the light strip and press it down for 10-15 seconds.
Secure the controller with the adhesive pads. Do not move it
to other place after it is attached.
• NOT FOR EMERGENCY LIGHTING
• Not intended for recessed installation in ceilings, or sots.
• Only use the control provided with or specied by these
instructions to control this device.
• To prevent re danger, do not run cord behind walls, ceilings,
sots, or cabinets where it may be inaccessible for examination.
• Use only insulated staples or plastic ties to secure cords.
• The maximum distance to the receptacle is determined by the
length of adapter cord.
• Keep the device away from water, re, humidity or hot
environments.
• Do not attempt to disassemble, repair, or modify the device. If you
need service, please contact us.
• Do not use the device where wireless devices are not allowed.
• Do not use damaged charger or USB cable to charge the device.
• Do not use any other chargers than those recommended.
• Adapter shall be installed near the equipment and shall be easily
accessible.
4. Plug in the power adapter to power on your light strip.
Safety Notice
• Route and secure cords so that they will not be pinched or
damaged when the cabinet is pushed to the wall;
• Position the portable cabinet light with respect to the cabinet
so the lamp replacement markings are able to be read during
replacing;
• The National Electrical Code (NEC) does not permit cords to be
concealed where damage to insulation may go unnoticed. To
prevent re danger, do not run cord behind walls, ceilings,
sots, or cabinets where it may be inaccessible for
examination. Cords should be visually examined periodically
and immediately replaced when any damage is noted.
Support
For technical support, the user guide and other information,
please visit https://www.tp-link.com/support/.
Install Your Light Strip
Altri manuali per Kasa Smart
3
Altri manuali TP-Link Apparecchio di illuminazione
Manuali Apparecchio di illuminazione popolari di altre marche
Emos
Emos CLASSIC ZY1431T Manuale utente
Westinghouse
Westinghouse Outdoor Lighting Fixture Manuale utente
Hedler
Hedler C 12 silent Manuale utente
Blizzard Lighting
Blizzard Lighting Puck: CSI Manuale utente
Energetic Lighting
Energetic Lighting ELYSL-5004 Series Manuale utente
Lightmaxx
Lightmaxx Shaft 5R Manuale utente
Cooper Lighting
Cooper Lighting Halo L3232E Manuale utente
Stageline
Stageline ODW-2410RGBW Manuale utente
Light Sky
Light Sky Tornado Series Manuale utente
Lightolier
Lightolier Paralyte 2424 PLA2G9LS26U Manuale utente
Lightolier
Lightolier Lytespan 83ED17S Manuale utente
Lightolier
Lightolier Calculite CS8226 Manuale utente