TP-Link TL-R402M Manuale

Altri manuali per TL-R402M

1

Indice

Altri manuali TP-Link Router di rete

TP-Link

TP-Link TD-W9980B Manuale utente

TP-Link

TP-Link AC2300 Manuale utente

TP-Link

TP-Link TL-WR945N Manuale utente

TP-Link

TP-Link td-w8970 Manuale utente

TP-Link

TP-Link AC2100 Manuale utente

TP-Link

TP-Link tl-wr845n Manuale utente

TP-Link

TP-Link TL-WR1043ND Manuale utente

TP-Link

TP-Link Archer C2 Manuale utente

TP-Link

TP-Link TL-MR3020 Manuale utente

TP-Link

TP-Link Deco X20-4g Manuale utente

TP-Link

TP-Link Deco WE10800 Manuale utente

TP-Link

TP-Link TL-PA7020P Manuale utente

TP-Link

TP-Link TL-MR3020 Manuale utente

TP-Link

TP-Link Archer C6 Manuale utente

TP-Link

TP-Link TD-W8968 Manuale utente

TP-Link

TP-Link Archer VR600v Manuale utente

TP-Link

TP-Link SafeStream TL-R480T+ Manuale utente

TP-Link

TP-Link TL-ER6020 Manuale utente

TP-Link

TP-Link ARCHER C3150 Manuale utente

TP-Link

TP-Link Archer C20 Manuale utente

TP-Link

TP-Link TL-WR703N Manuale utente

TP-Link

TP-Link SafeStream TL-ER6120 Manuale utente

TP-Link

TP-Link TL-WR802N Manuale utente

TP-Link

TP-Link TL-WR850N Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza

LevelOne

LevelOne FBR-1416 Manuale utente

Rev. 1.3 – 01/07/2009

TP Link Router Basic Setup

Introduction

The TP-Link #TL-R402M Cable/DSL Router is a broadband router. Detailed information is on

the vendor’s web site at http://www.tp-link.com.

A router assigns Dynamic Host Configuration Protocol (DHCP). This means the router

assigns Internet Protocol (IP) addresses to all connected equipment configured to request on.

The two basic rules for DHCP:

•Only one router can be active in the same group of connected equipment.

•Each equipment item must have a unique IP address. If two devices get the same IP,

erratic behavior will result – most often the duplicate IP will fail to communicate.

By default, DHCP is on in this router.

Package Contents:

•TP-Link TL-R402M Router

•Power Adapter

•Quick Installation Guide

•Resource CD

You must own or purchase 1 network cable; the most common is a 6 foot

length. While sold under various names, make sure it is Cat5E type, with the

RJ-45 connectors.

Installation Planning

Consult the TP-Link Quick Installation Guide for an overview. The TP-Link TL-R402M unit is a

broadband router, so it must work with your cable or dsl modem. Your existing Cable or DSL

modem must also have one Ethernet port, which is probably connected to your PC.

Double-check that your internet works with the existing Cable or DSL modem before

you try to add the router. If you don’t have functioning internet before proceeding,

contact your Internet Service Provider (ISP).

Rev. 1.3 – 01/07/2009

Home Installation of the TP-Link Router

1. Power down all existing equipment (computer, cable/dsl modem, etc.).

2. Locate a suitable location for the TP-Link router.

3. On your cable or dsl modem, find the Ethernet port

and follow the (network) cable from the port of the

modem to the network card on the PC.

4. Unplug the PC end of the cable, and plug it into the WAN port on the TP-Link router.

[Note: you use the WAN port if you will leave DHCP on and use this device as a router.]

5. Now take the extra Ethernet cable (from page 1), and plug one end into the network port

on the PC (where you just removed your modem’s cable in step 4 above).

6. Plug the other end of the extra cable into any open LAN port on the TP-Link router (see

picture in step #4). Tip: It can keep you organized to use port #1, but this isn’t strictly

necessary.

7. Connect the A/C adapter to the router, and it will power on.

8. Power on the primary PC and the cable/dsl modem.

9. Recheck that your basic internet still works on the PC.

10. Proceed to the Weather Direct gateway installation, if that is your goal

(www.weatherdirect.com).

Note: If you have internet service problems at this point, the two most common errors are:

a) a mistake in the cabling, so check the connections in steps 1-9 again or

b) missing that DHCP is enabled on either the cable/dsl modem or some other routing

device. Only one device can serve DHCP, so competing devices need DHCP disabled.

If you have any additional needs, you will need to consult the TP-Link Users Guide on the CD

that came with the router or our Router Trouble-Shooting handout.

LAN

ports