Trader ARCTIC OWL OWPIROD Manuale utente

OWPIROD

Outdoor Infrared Sensor

Specifications

Supply Voltage 220-240V AC 50Hz

Maximum Incandescent Lighting Load 10A 2400W

Maximum Induction Load 5A 1200W

Sensor Power Consumption 0.7W

Detection Method Passive Infrared

Weatherproof Rating IP66

Time Delay 5 to 10 seconds

Warm up to 30 seconds

Detection Angle Up to 110°

Detection Distance Up to 18m

Safety Information

The OWPIROD is a mains connected device and is intended for installation in a fixed location

by a Licensed Electrical Contractor in accordance to applicable Australian wiring rules. The

product must be installed and used in conjunction with detail provided in the enclosed

instructions, failure to do so may cause serious injury. The product contains no user servicable

parts and must be returned to GSM Electrical (Australia) Pty Ltd (GSME) if the product is

damaged and requires repair.

Installation

Before installing your new Arctic Owl (OWPIROD) Outdoor PIR Sensor, it is most important that

you read and follow these instructions, even if you feel you are quite familiar with this type of

product. Keep this document handy for future reference. (If you are the electrical contractor,

please leave the instructions with the client after installation for their future reference).

When operating with standard lighting loads, ensure the lights are pointing away from the

sensor head. Light from the lamps may cause false re-triggering and heat from globes may

harm the sensor unit if too close. The base of the Arctic Owl can be installed in a vertical

manner; such as walls, fascias, or alternatively it may be installed on horizontal surfaces such as

ceilings and under eaves.

When installing onto porous, rough or uneven surfaces (such as brick walls), care should be

taken to ensure that water and dust will not gain ingress into the base of the unit through the

use of a silicon or similar sealant compound. A foam sealing gasket is provided for all other

installation types. It may also be necessary to install the base onto a conduit box or surface

mounting block depending on location.

FIG 1 AB

Steps for Installation:

1. Switch power OFF at meter box.

2. Refer to FIG 1. Use the holes (A) on the Mounting Base (B) to mark the position of the

fixing screws on the selected mounting surface once the mounting position has been

established.

3. If wall pugs are to be used for securing the base of the unit, drill to a depth of

approximately 40mm, and fit the supplied plastic wall plugs as appropriate. Take care not

to drill into concealed electrical wiring or other services. Wall plugs must be pushed in

until flush.

4. Drill suitable sized hole for cabling in mounting surface between the other two mounting

holes for electrical connections (C).

5. Ensure gasket is positioned over wiring before connecting (D).

6. Pull through electrical wiring in preparation for connection to the sensor.

7. Connect the Active incoming supply connection to the terminal block connection marked

“L’’, as per FIG 2.

8. Wire the incoming supply Neutral and the load Neutral connection to the terminal block

connection marked “N’’, as per FIG 2.

9. Wire the load active connection to the switched Active output connection on the terminal

block marked “S”, as per FIG 2.

NOTE: Installation must be carried out according to Australian Wiring Rules (AS/NZS 3000).

Please refer to the wiring diagram in FIG 3.

10. Remove protective backing from self-adhesive foam gasket (D) as per FIG 1.

11. Attach the self-adhesive foam gasket to the mounting surface or rear of base, aligning

holes in the gasket (E) to the wall plugs as per FIG 1.

12. Fit the sensor mounting base (B) to the wall using screws provided and ensure tightly

secured to maintain IP rating and also tighten adjusting nuts to seal the cable and lock the

head in place.

13. Ensuring that associated lighting loads are correctly installed according to Australian

Wiring Rules.

14. Reconnect power.

FIG 2 FIG 3Removable terminal block

Set Up & Operation

The Arctic Owl OWPIROD Outdoor Sensor is equipped with a highly sensitive PIR (Passive

Infrared) motion detector. A multi-cell technology fresnel lens is used to divide the sensors

basic detection range into multiple separate segments or zones. The sensor automatically

scans for movement between zones, and then will activate connected devices (such as security

lighting) as a result.

The OWPIROD Outdoor Sensor will provide optimal performance and range when installed

in a vertical position approximately 2.5m above the ground; as is shown in the diagrams in

FIG 4 below. The sensor head can be adjusted to allow optimal coverage for the zone of the

detection area by adjusting the head. The horizontal coverage zone can reach up to 18m with

an angle of 110° from the lens.

110°

approx

18m

5°

tilt

4m 8m 18m

2.5m

FIG 4

To adjust sensor head (refer to FIG 5):

Simply loosen the two ball joint locking nuts (A), located at either end of the sensor arm (B),

adjust sensor head (C) and tighten nuts (A).

NOTE: Always loosen locking nuts on sensor before adjusting. Failure to do so can damage the

sensor or crack the lock nut.

Time Duration: The length of time the sensor will activate a light or other load after detection

can be adjusted from 5 seconds to 10 minutes. Rotating the time knob (marked with the clock)

anti-clockwise will reduce the duration time.

LUX Level: The sensor has a built in photoelectric cell that automatically detects daylight

and darkness levels. Rotating the lux control knob anti-clockewise (marked with the day/

night image), will ensure that the sensor only works at night. By rotating the lux control knob

clockwise, the sensor will work in both daylight and at night depending on the application -

this setting is primarily used for testing the sensor after installation.

Sensitivity: The sensitivity control (marked with the sensor symbol) allows you to adjust the

sensitivity of the Infrared detector. This adjustment is useful to adjust the sensitivity of the PIR

to prevent false triggering and to adjust the detection range. Unless required, the sensitivity

adjustment should be operated with the knob turned fully clockwise.

FIG 5

Time Duration

Lux Level

Sensitivity

Walking the Zone to Commission Installation

1. Rotate the lux knob fully clockwise for daylight operation, set the time control to min

(Anti-clockwise) and the sensitivity to maximum (clockwise).

2. Turn on the power at the isolating switch. The load device should turn on for a short

period of time.

3. Wait 30 seconds for the circuit to stabilise.

4. If not already adjusted, direct the sensor toward the desired area, adjusting the elbow

joint on the sensor arm. Loosen all nuts on sensor before adjusting.

5. Have another person move across the centre of the detection area and slowly adjust the

angle of the sensor arm until the light is switched on. Your sensor is now aimed at your

selected area.

6. Adjust the time control to the desired level.

7. Adjust the sensitivity (if required) to limit detection range. This can be tested via walk

testing.

8. Adjust the lux control by rotating anti-clockwise to revert to night time operation. If the

lights are required to switch on earlier, e.g. dusk; wait for the desired light level, and

slowly turn the lux knob clockwise while someone walks across the centre of the detection

area. When the lights switch on, release the lux control knob.

Manual Override Feature

When the power is initially turned ON, the fitting operates in AUTO mode. In this mode, the

sensor turns the light ON and OFF automatically.

The manual override function means that the fitting can be put permanently “ON”. In this

mode the PIR sensor is disabled.

Resetting the Fitting into “Manual Mode”

9. To bypass the “auto mode” and set the fitting into “manual mode”, turn the wall switch

“OFF” and “ON” once within 3 seconds.

Wall switch action: OFF ON

10. Wait for 3 seconds and the light will turn “ON” permanently and the fitting will be in the

“manual mode”.

Note: If the wall switch action is done more than twice, the fitting may not enter into “manual mode”.

Setting the Fitting into “Auto Mode”

1. To change back to “auto mode”, turn the power “OFF” and wait for about 10 seconds,

then turn it back “ON” again turning the switch “ON” once only.

Wall switch action: OFF, wait 10 seconds ON

2. The PIR sensor will enter into the “Warm-up” mode and the lights will stay “ON” for 10

seconds, then will turn “OFF”.

3. Now wait for about 10 seconds for the circuit to stabilise and the fitting will operate now

in “auto mode”.

Warning: The manual override is linked with the lux setting, and switching on the manual

override will only function at night if the sensor settings are set to functioning in the dark.

It will only work during the day if the lux level is set to daylight.

After Installation & Set Up

To ensure the installation is functioning properly and meets the security/lighting needs, further

adjustments may be required to maintain ideal light level and sensitivity settings.

To ensure a continued high level of performance, ensure the sensor head lens area is regularly

cleaned (3 monthly intervals) from spider webs and dust using a damp cloth.

Troubleshooting

Problem Reason Solution

Unit will not

operate during

daylight.

Sensor not

in daylight

operation mode.

Rotate lux control fully clockwise.

Sensor false

triggering.

Unit may be

suffering from

false activation.

1. Cover sensor unit with a black cloth for a period

of 5 min to check that the light does not trigger.

Occasionally, winds and drafts may activate the sensor.

Sometimes passages between buildings etc. can cause a

“wind tunnel’’ effect.

2. Ensure the unit is not positioned so as to allow

detection of cars/people using public thoroughfares

adjacent to the property. Adjust the sensitivity control

accordingly to decrease range of sensor or adjust

direction of sensor head.

Sensor not

turning off.

Sensor re-

triggering during

operation.

Stand well out of the detection range and wait (the

warm-up period should never exceed 1 minute). Then

check for any extra sources of heat or movement within

the detection area such as animals, trees, light globes

etc. and adjust sensor head and controls accordingly.

PIR will not

operate at

night.

Too much

ambient light.

The level of ambient light in the area may be too bright

to allow operation. Adjust lux level control accordingly

and remove any other sources of ambient light.

PIR sensor will

not operate

at all.

No power.

Check that the power is switched ON at the circuit-

breaker or internal wall switch. Ensure that connections

are not loose.

Unit activates

during the

daytime.

Low level of

ambient light or

lux level control

set incorrectly.

The level of ambient light in the area may be too dark

to allow operation in night time only mode. Re-adjust

the lux control accordingly.

5 Year Manufacturer’s Warranty

This product has been manufactured to the highest quality standards.

This product is warranted to the original purchaser and is not transferable.

The product is guaranteed to be free from defects in workmanship and parts for a period of 5

Years from the date of purchase. Defects that occur within this warranty period, under normal

use and care will be repaired, replaced or refunded. The benefits conferred by this warranty

are in addition to all other rights and remedies of the consumer under Commonwealth,

State and Territory laws in relation to the goods or services to which this warranty relates

and Australian Consumer Law. Risk in regard to the product to be repaired shall at all times

remain with the Purchaser. The warranty is given on the condition that the product to which it

applies is used for the purpose and in the manner intended by its construction and for no other

purposes whatsoever. GSM Electrical (Australia) Pty Ltd shall not be responsible for damage

of any kind, caused by accidents, power surges, electrical storm damage, incorrect power

current, infestation (vermin or insect), incorrect installation, incorrect electricity or plumbing

installation, improper use of controls or failure to use the product in accordance with the

operating instructions, general misuse or abuse or from normal wear and tear. Any attempt by

an unauthorised person to repair or tamper with the equipment shall render the warranty null

and void.

GSM Electrical (Australia) Pty Ltd’s liability under this warranty is limited to the replacement

and/or repair of the defective parts within the warranty period and does not extend to

installation or removal of the product. Acceptance of liability by GSM Electrical (Australia) Pty

Ltd contained herein is to the exclusion of any other remedy whatsoever and howsoever arising

in respect of any equipment to which it applies.

GSM Electrical (Australia) Pty Ltd

Level 2 142-144 Fullarton Road

Rose Park SA 5067

www.gsme.com.au

Phone: 1300 301 838

Fax: 1300 301 778

Indice

Altri manuali Trader Sensore di sicurezza

Trader

Trader SCORPION SCSPSENSORBK Manuale utente

Trader

Trader ARCTIC OWL OWPIR360 Manuale utente

Trader

Trader ARCTIC OWL OWPIROD 180 Manuale utente

Manuali Sensore di sicurezza popolari di altre marche

THORLABS

THORLABS PDA10JT Manuale utente

Waeco

Waeco UV-DETECT Manuale utente

Intermatic

Intermatic IOS-DSIMF Manuale utente

urmet domus

urmet domus 1083 Manuale utente

Siemens

Siemens AZL66 Series Manuale utente

BTI

BTI Profiline Multi Finder Manuale utente

Challenger

Challenger SL01 Manuale utente

DMP Electronics

DMP Electronics 1122INT Manuale utente

Rielta

Rielta Ladoga MK-RK Manuale utente

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuale utente

Bosch

Bosch DS835 Manuale utente

DBI SALA

DBI SALA EZ Stop Manuale dell'operatore

Lamptime

Lamptime ST05C Manuale utente

Ubiquiti

Ubiquiti MFI-MSC Manuale utente

Subsite

Subsite 910R Istruzioni per l'installazione

Satel

Satel OPAL Pro Manuale utente

Aleph

Aleph XC-1XTEU Manuale utente

Pima

Pima LARIS QUAD Manuale utente