TrailFX DHS010B Manuale utente

Page 1 of 5

TrailFX Drop Down Step

Part No. DHS010B / DHS011B

Fits: F-150 SuperCrew 2015-2019; F-250 / 350 SuperCrew

2017-2019 F-150 SuperCab 2015-2019; F-250 / 350 Super-

Cab 2017-2019

Product image

TO AVOID BEING SCRATCHED, PLEASE PROTECT THE SURFACE OF

THE TAILGATE VENT COVER CAREFULLY.

REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.

PARTS LIST:

Item Qty Part Description Tools Needed

11Step Bar Driver Side 13 MM SOCKET & WRENCH

21Step Bar Passenger Side 14 MM SOCKET & WRENCH

32Front Mounting Bracket 15 MM SOCKET & WRENCH

44/2 Center and Rear Mounting Bracket RATCHET

56/4 Support Bracket TORQUE WRENCH

618/12 M8 Plastic Retainer

724/16 M8 Nut

824/16 M8 Lock Washer

924/16 M8 Flat Washer

10 6/4 M8 Square Neck Bolt

11 12/8 M10 Flange Bolt

12 12/8 M10 Flange Nut

SMALLER QUANTITIES FOR SUPERCAB APPLICATIONS

ALIGN THE STEP BARS AS DESIRED AND TIGHTEN ALL M10 FASTEN-

ERS TO 30 ft. - lbs., AND THE M8 FASTENERS TO 15 ft.-lbs.

READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.

60 min Drilling Not

Required

Cutting Not Re-

quired

Mounting Kit Images

ITEM 3 ITEM 4

ITEM 5

Page 2 of 5

4. Grab a support bracket and loosely install to mount bracket with (1) M8

Square Neck Bolt, (1) M8 Flat Washer, (1) M8 Lock Washer, (1) M8 Hex

Nut. See Figure 3.

5. Repeat for the other 5 brackets.

1. Start at the front driver side of vehicle and locate the factory studs. Grab

(3) Plastic retainers and thread on to the factory studs. See Figure 1 & 2.

2. Repeat for center and rear locations.

3. Repeat for passenger side

INSTALLATION PROCEDURE

Factory studs

shown

Front Driver

side shown

987

FIGURE

FRONT

Item 4Item 4 Item 3

DRIVER SIDE SHOWN

Page 3 of 5

INSTALLATION PROCEDURE

9. Grab Driver Side Bar and loosely install to mount brackets with (6) M10

Flange bolts and (6) Serrated Flange Nuts. See Figure 5.

10. Repeat for passenger side.

6. Start at the front driver side of vehicle and grab Front Mount Bracket. Use

(3) M8 flat washer, and (3) M8 lock washer, and (3) M8 hex nuts to

loosely mount bracket to the rocker panel. See Figure 4.

7. Repeat for center and rear locations.

8. Repeat for passenger side

FIGURE

11 12

798

FIGURE

Page 4 of 5

COMPLETE INSTALLATION

Page 5 of 5

Keystone Automotive Operations Inc. (KAO) warrants this product to be free of defects in material and workmanship at the time of pur-

chase by the original retail consumer. KAO disclaims any other warranties, express or implied, including the warranty of fitness for a

particular purpose or an intended use. If the product is found to be defective, KAO may replace or repair the product at our option,

when the product is returned prepaid, with proof of purchase. Alteration to, improper installation, or misuse of this product voids the

warranty. KAO’s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for any

incidental or consequential loss or damage.

Check out these other TrailFX Products!!

PRODUCT CARE

FAQ’s

1. Mounting bracket are not getting Installed properly.

In some cases Illustration images shown in Installation manual may not be the exactly same as per actual vehicle images ,also if Driver / Passenger side

mounting brackets are very identical in the design, suggest referring Parts Identification guide to avoid fitment issue.

2. Products are thumping / rattling after installation.

Please ensure that all required mounting brackets / hardware’s are installed & tighten correctly. Suggest using white lithium / regular grease between the

metal to metal contact surfaces.

3. Missing / Excess Hardware.

Recheck hardware count as per the part list.

4. Product not installing properly.

Ensure make model year, cab length and bed size of your vehicle is listed in the application. All installation steps are followed correctly.

Learn more about running boards on our website.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali TrailFX Accessori per automobili