TRAP-IT ABDLR-30 Manuale utente
Caution: Always Wear Laser Protective Eyewear
OPERATION MANUAL
LR
TRAP-IT® LR BEAM DUMPS TRAP-IT® LR BEAM DUMPS
23
DESCRIPTION
TRAP-IT™ Low Reectance beam dumps are safety devices
that dissipate incoming laser power. The surface nish pro-
vides < 3.5% reectance from 190-10,600nm. Place beam
dumps in a position along the optical beam path to provide
a nal beam stop. For applications that range outside product
specications, we recommend users expand the beam size
with a negative lens to lower the power density level.
2 .
1.
REFLECTANCE GRAPH
TRAP-IT® LR BEAM DUMPS TRAP-IT® LR BEAM DUMPS
23
LASER SAFETY
Depending on the operating parameters of the laser source
and the potential to exceed MPE (Maximum Permissible
Exposure) limits, there may be a signicant risk of eye injury.
Under such conditions, we recommend using appropriate
laser protective eyewear. Laser protective eyewear must be
evaluated in accordance with ANSI Z136.1 Standard for the
Safe Use of Lasers.
3 .
TRAP-IT® LR BEAM DUMPS TRAP-IT® LR BEAM DUMPS
45
INSTRUCTIONS
1. Calculate your laser beam average power and maximum
power density.
2. Never place the product in a location above the maximum
suggested power density, as damage could occur to the
product nish.
3. Position the laser beam centerline within the TRAP-IT™ LR
target.
4. If this product is used as a control measure, make sure it
is fastened to the table to prevent it from being moved or
knocked over.
4 .
TRAP-IT® LR BEAM DUMPS TRAP-IT® LR BEAM DUMPS
45
PREVENTIVE MAINTENANCE
Depending on the frequency of use and the number of
personnel that have access to the laser application, we
recommend you inspect the product daily or weekly.
• Verify the product is in the correct orientation to the
incoming laser beam.
• Verify that the absorbing target surface hasn’t been
damaged by the laser.
• Clean with methanol alcohol or acetone, use very light
pressure as coating is sensitive to physical damage.
COMPLIANCE
This product line is RoHS, REACH, ISO 9001:2015, AS9100
compliant.
6 .
5 .
Part Number Target Aperture Spectral Sensitivity Max. Average Power Damage Threshold Thermal Management
ABDLR-30 1.18 inch [30mm] 190-10,600nm 50 watts 20 watts/cm2Convection Cooled
ABDLR-30NP 1.18 inch [30mm] 190-10,600nm 50 watts 20 watts/cm Convection Cooled
ABDLR-51 2.00 inch [50.8mm] 190-10,600nm 50 watts 20 watts/cm Convection Cooled
ABDLR-51NP 2.00 inch [50.8mm] 190-10,600nm 50 watts 20 watts/cm Convection Cooled
ABDLRT-90 3.54 x 3.54 inch [90 x 90mm] 190-10,600nm 50 watts 20 watts/cm Convection Cooled
ABDLRT-90NP 3.54 x 3.54 inch [90 x 90mm] 190-10,600nm 50 watts 20 watts/cm Convection Cooled
ABDLRT-50 2.00 inch [50.8mm] 190-10,600nm 20 watts 20 watts/cm Convection Cooled
STAND-ITM Optical Stand with M6 Thread
LR
TRAP-IT® LR BEAM DUMPS TRAP-IT® LR BEAM DUMPS
67
kenteklaserstore.com
©Kentek Corporation. All rights reserved.
Rev. 04/23
Questo manuale è adatto per i seguenti modelli
7
Indice
