TreadReader HANDHELD Manuale utente
TREADREADERTM
HANDHELD 3D SCANNER
QUICK GUIDE
01 Warnings
02 CE marking and declaration of conformity
03 Disclaimer
04 Safe use of a laser product
05 Label and label position
06 Specications
07 Contents
08 Scanner keypad and leds
09 Switching the scanner on and off
10 How to connect to the smartphone/tablet
11 Login/upload to TREADMANAGERTM in the app
12 Entering vehicle registration
13 Scanning a tyre
14 Charging
15 Maintenance and cleaning
16 Calibration check
17 Factory reset
18 Further information
02
03
03
04
05
06
06
07
07
08
10
12
12
15
15
16
18
18
Redening tire measurement
CONTENT
4
TREADREADERTM HANDHELD • QUICK GUIDE
Avoid shock and vibration to this product. Use the wrist lanyard provided to avoid
droppage. Avoid continuous exposure to dust and liquid spray. Avoid direct exposure
to aggressive substances, e.g. reactive chemicals, cleaning agents.
Do not view the laser directly with an unprotected eye or optical instrument. Lasers
are potentially hazardous to the eye. This product contains a Li-Ion battery. Do not
heat or burn. Do not charge at temperatures below 0ºC (32ºF) or over 45ºC (113ºF).
Charge using manufacturer supplied charger only.
This product contains a laser that could be damaged during unauthorised repair
or disassembly, which could result in hazardous exposure to laser radiation. This
equipment should only be serviced by an authorised service provider. Do not attempt
to open this product as any warranty will be voided.
Use of this product other than as specied in the user manual may result in hazardous
radiation exposure. The user manual can be found at treadreader.com/library.
This product conforms to:
EU directive 2014/30/EU – Electromagnetic conformity
EU directive 2012/19/EU – Waste electrical and electronic equipment
Snap-on Equipment S.r.l. Via Prov. Carpi, 33 2015 Correggio (RE) Italy
01 • WARNINGS
02 • CE MARKING AND
DECLARATION OF CONFORMITY
5
TREADREADERTM recommends only those applications of TREADREADERTM tyre
measurement products as specied within TreadReader product literature, technical
information, and warranty statements.
TREADREADERTM accepts no liability for use of its products in applications other
than those for which they are designed. It is the responsibility of the driver, or vehicle
owner, or operator, to ensure tyres have sufcient tread depth, are defect free and
are in a roadworthy condition.
03 • DISCLAIMER
04 • SAFE USE OF A LASER
PRODUCT
IEC 60825-1:2014 Safety of laser products was created to prevent accident by a
laser product and to protect users. This regulation classies laser products according
to the level of hazard and provides safety measures for the respective classes.
This product is classied Class 1 Laser product per IEC 60825-1:2014.
This product complies with FDA radiation performance standards 21 CFR Subchapter J.
CLASS
Class 1
Class 1M
Class 2M
Class 3B
Class 2
Class 3R
Class 4
DESCRIPTION OF HAZARD
Safe under normal conditions of operation
Safe under normal conditions of operation except for diverging or large area beams
when collecting optics are used. Hazardous when collecting optics used.
Visible beam, low power. Blink response of eye affords protection. Hazardous when
collecting optics used.
Direct intra beam viewing is hazardous.
Visible beam, low power. Blink response of eye affords protection.
Direct intra beam viewing is hazardous, but the risk is lower than Class 3B.
High power. Capable of producing hazardous diffuse reections. Capable of
producing skin burns and re hazardous.
6
TREADREADERTM HANDHELD • QUICK GUIDE
The following label is afxed to this product in accordance with the relevant EU
directives.
05 • LABEL AND POSITION
06 • SPECIFICATIONS
DESCRIPTION
Dimensions (LxWxH)
Weight
Environmental rating
Laser
Scan zone
SPECIFICATION
186mm x 96mm x 84mm (7.3” x 3.8” x 3.3”)
< 650g
IP54
Android version 5.1 or laterMobile device software
requirement
Class 1, 660nm, visible laser, max power output is less < 0.1mW
50mm x 26mm (2”x1”)
< 0.2mm (0.008”)
0°C to 50°C (32°F to 122°F)
5V DC rechargeable Li-Ion battery
Measurement accuracy
Operating temperature
Power
7
07 • CONTENTS
08 • SCANNER KEYPAID AND LEDS
This product comprises:
1 x TREADREADERTM 3D hand held scanner
1 x Mobile device, software license (TREADREADERTM hand held scanner app is
downloaded from App Store)
1 x Rigid plastic carry case
1 x Calibration check piece
1 x USB 3 charging cable and power adaptor
12 month calibration certicate
There are three buttons on the scanner. The LEDs indicate power (on/off),
wi- connectivity, battery level and scanner status.
Power (On/Off) Battery level/
scanner status
Transmitting data 67 - 100%
Ready to scan
Wi-Fi mode 34 - 66%
Processing data
Wi-Fi on/off 0 - 33%
Fault
8
TREADREADERTM HANDHELD • QUICK GUIDE
To switch the hand held scanner on or off, hold down the power (on/off) button for 3
seconds.
09 • SWITCHING THE SCANNER
ON AND OFF
10 • CONNECTING TO THE
SMARTPHONE/TABLET
TREADREADERTM provides the mobile software application (app), TREADREADERTM
HandHeld Scanner which can be downloaded from the app store, for phones or
tablets to control the scanner.
Switch on the hand held scanner. Launch the app on your phone or tablet.
The app home screen gives an option of direct mode or network mode.
Select either direct mode or network mode. If prompted for the wi- password, the
default password is 12345678.
9
Direct mode: Allows for a one-to-one connection between the phone or tablet and
the scanner. Once the direct mode has been selected a number of networks will
appear on the app screen. Select the desired scanner (serial number located on rear
of hand held). The phone or tablet and scanner will be paired when both the bottom
and middle left LEDs light up blue and the device buzzes.
Network mode: Allows the scanner to connect to an external wi- network (stand
alone router). The phone or tablet will access the scanner in the same way that any
other device is accessed on a wi-fi network, such as a printer.
To enable Network Mode:
1. Connect the scanner in the direct mode
2. Hide keyboard to access settings menu, using the
Android back button.
3. In the settings menu (see below), select network
4. Select the relevant network/stand alone router
5. Enter the password for the network/router
6. Wait for the scanner to connect to the chosen
network
7. Once the top and bottom left LED light up, press
return on screen
8. The app will return to the home screen (as shown
on page 8)
9. Select option to connect to the scanner in network
mode.
10. You will be asked to choose your desired network / stand alone router)
11. Press and hold the scanner wi-fi button to broadcast the IP address of the
scanner, at which point all three blue LEDs will light up. The scanner will buzz
at which point, press discover in the app. Keep pressing the button (for up to 15
seconds) until the scanner reboots.
12. Note: this is required for rst time connection in network mode only
10
TREADREADERTM HANDHELD • QUICK GUIDE
HandHeld app releases after 11.53.1.0 include the ability to upload scans to
TreadManager. Android 6.0 or later is required for this option to be available.
1. When starting the app, the landing page will have a login to TREADREADERTM
button below the direct mode/network mode option.
2. Ensure the Android device is connected to the internet when pressing the login
button.
3. For rst time use, enter the email and password, then press the large cloud icon to
login. If successful, it will take the user to the initial landing page.
4. The landing page should now conrm the user has logged in.
11 • LOGIN/UPLOAD TO
TREADMANAGERTM IN THE APP
13. Once the top and bottom left LED lights up, press connect on screen. Do NOT
release the wi-fi button
14. The app will display the network you have chosen in the top left of the screen
15. You will be asked to choose your desired network / stand alone router)
16. Press and hold the scanner wi-fi button to broadcast the IP address of the
scanner, at which point all three blue LEDs will light up. The scanner will buzz
at which point, press discover in the app. Keep pressing the button (for up to 15
seconds) until the scanner reboots.
17. Note: this is required for rst time connection in network mode only
18. Once the top and bottom left LED lights up, press connect on screen. Do NOT
release the wi-fi button
19. The app will display the network you have chosen in the top left of the screen
Altri manuali per HANDHELD
2
Indice
Altri manuali TreadReader Scanner
